Search Documents

By M. Imamura

Sumitomo Metal Mining Co., Ltd. has developed a novel hydrometallurgical process for producing not only copper metal but also iron metal from copper concentrates. Because copper concentrates generally contains the same amount of iron as copper, cost-effective rejection of the iron is a key issue for the development of the process. Conventional hydrometallurgical processes produce a large volume of goethite or hematite for disposal and the residues are not environmentally friendly. In the novel Sumitomo hydrometallurgical process, copper is leached effectively from chalcopyrite concentrates using chlorine gas, followed by purification through solvent extraction and electrowinning for copper and iron recovery. This process has many advantages such as the minimization of the volume of solid waste by the recovery of metallic iron and the production of high purity copper. Iron metal with a purity of more than 98% can be recovered from the purified raffinate. This paper presents the results of the batch and continuous tests of the process flowsheet.

Jan 1, 2006

By William J. Coulter

WITHIN the United States the problem of meeting maximum production by our metal mines has been solved by: (1) Conservation of man power by mechanization. (2) Increasing man-power efficiency as expressed in tons per man-shift by the adoption of new and more efficient methods. (3) Production from submarginal properties made possible by some form of government subsidy. (4) Selective mining of high-grade areas. (5) Drawing on broken ore reserves and reducing advanced development work to a minimum. (6) Making maximum use of available equipment. (7) Repairing equipment that normally would be replaced. (8) Working a seven-day week on a three-shift basis to get maximum use of equipment and man power. (9) Adoption of incentive plans to increase maximum efficiency and unit production. (10) Important advancement in metallurgy, resulting in larger recoveries. (11) Improvements in safety, health, and general working and living condi-

Jan 1, 1945

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By AIME AIME

LIFE will not be difficult for those who attend the fall meeting of the Petroleum Division at the Conoco Club, Ponca City, Okla., Sept. 30-Oct. 1. An attractive program to appeal to oil company executives and lawyers, as well as technologists, has been arranged and the Continental Oil Co. has contributed for the occasion the buildings, grounds and facilities of the club. E. 0. Bennett, Continental Oil Co., Ponca City, is chairman of the arrangements committee, and reservations for rooms and trips, requests for information, etc., should be sent to him.

Jan 1, 1932

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By J. Pesl, U. Kemey, F. Sauert

"The CONTOP® smelting cyclone is a water-cooled, upright, high-intensity smelting reactor. The technology for the reactor was initially developed and brought into industrial-scale operation in the area of non-ferrous metallurgy. The two largest smelting cyclones were built with a capacity of 32 tons per hour of copper concentrate mix.The newest industrial CONTOP® plant treats up to five tons per hour of zinc-bearing residues including EAF dust. The highly concentrated zinc-lead oxide produced is sold to the zinc industry. The slag fulfills the leaching criteria and is used in waterway construction. The heat transferred to the cyclone cooling system and the off-gas boiler produces steam from which power is generated in a turbine.V AI has erected a new CONTOP® demonstration plant at MEFOS, Lulea, Sweden. A zinc volatilization rate of 90% was achieved during hot commissioning with Swedish EAF dust.Treatment costs in the range of 85 to 100 EUR per ton were estimated in a feasibility study on the treatment of 73,000 and 57 ,000 tons EAF dust for a group of steelmaking mills in Southern Europe."

Jan 1, 2000

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between, the Coordinating Fuel Research (C.F.R.) Committee of the Coordinating Research Council (C.R.C.) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36.-4/ Further reports have been issued describing motor gasolines sold during the succeeding summers and winters to the summer of 1941 and during the winter of 1942-43 and the summer of 1943 5/ No reports were made on motor gasolines sold during the winter of 1,) 41-42 and during the summer of 1942. The present report presents analytical data for 1,356 samples, representing the products of approximately 103 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium-price, and third-grade gasolines - and each group has been averaged separately. The number of samples, items and brands comprising each group is as follows: Regular-price, 770 samples, 286 items, and 94 brands; premium-price, 537 samples, 236 items, and 72 brands; third-grade, 49 samples, 31 items, and 18 brands. The meanings of these terms as used in the surveys are as follows:"

May 1, 1944

By S Doudle

The Iluka Resources Ltd Jacinth-Ambrosia heavy mineral sand mine (South Australia) is located in an undisturbed semi-arid landscape consisting of sparse trees, shrubs and grasses. The soil interspaces are covered with biocrusts, a living soil cover also found worldwide in arid regions. Biocrusts are composed of lichens, cyanobacteria, algae, mosses, liverworts, fungi and bacteria, and live on and within the first few millimetres of the soil surface. Biocrust organisms bind soil particles, sequester carbon and many fix atmospheric nitrogen making them important structural and functional components of ecosystems. Despite their important role in ecological processes, biocrusts are susceptible to disturbance; nevertheless they can recover provided sufficient inoculum is present. Cyanobacteria are the early colonisers and they capture atmospheric and landscape resources and establish conditions that subsequent successional seres can capitalise on. Research conducted in countries including China, Spain and South Africa has been focused on methods to either encourage rapid regeneration of cyanobacterial remnants or to introduce new material from cultured cyanobacteria. We have been investigating the extent and diversity of biocrusts across the 4500 ha mine lease and their potential to improve mining rehabilitation outcomes. Approximately 46 per cent of the soil surfaces are colonised with biocrusts and 33 taxa have been identified. Laboratory experiments were designed to mimic massive soil disturbance and treated with a range of water qualities. Within 22 days, treatments irrigated with fresh water were colonised by new cyanobacterial filaments with a mean surface coverage of 65 per cent. Secondary tests revealed that differences in the photosynthetic yield of the crust were dependent on the salinity levels of the irrigation water used. In 2011 this program is expanding from the laboratory into field scale trials designed to assess both the potential and practicalities of up scaling these techniques to provide crushed biocrusts and cyanobacterial bio-inoculum for use in mine rehabilitation.

Oct 5, 2011

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By R. L. Ziegfeld

It has often seemed to me that people are too prone to turn to new and untried materials in an effort to solve their problems, without giving sufficient consideration to the old stand-bys, except as a last resort, It?s a little like middle-aged men who are swept off their feet by the fresh beauty of a young girl without first considering the many advantages that a more mature woman has to offer. Maybe it?s because, like the older woman, the older materials have to make a determined effort to keep themselves looking young and attractive. T at?s just about the situation with which the lead industry is laced. We have to make a determined effort to keep lead looking young and attractive to industry. However, there is one difference and it is important, Lead can not only be kept looking young, but it can, in fact, actually be kept young, This results from two things. First, industry and technology are constantly changing. For example, we have known for years that the density of lead makes it ideal to stop gamma rays, but it is only recently that atomic fission as a source of gamma radiation has become an important tool of industry, That makes old knowledge about lead useful in developing a new market for it.

Jan 1, 1958

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

Alumina can be recovered from clay , using 30 percent nitric acid for digestion . Calcined clay is crushed and then digested at 325 ° F and 85 psig pressure with less than stoichiometric nitric acid required to form normal aluminum nitrate . In this way , a solution containing both normal aluminum nitrate , Al ( NO3 ) 3 , and basic aluminum nitrate , assumed to be Al ( OH ) ( NO3 ) 2 , is formed , and in which iron is virtually insoluble . The solution is filtered and then concentrated in vacuum evaporators to crystallize normal aluminum nonahydrate . The crystals are washed with 50 percent nitric acid and then decomposed to alumina and nitrogen oxides . The design that has been developed for this process is based on published work . For a plant producing 1,000 tons of alumina a day , the estimated operating cost is $60.69 per ton of alumina , and the estimated fixed capital cost is $ 76 million using a Marshall and Stevens chemical equipment index basis of 240.0 . This process is not competitive under current economic conditions with the production of alumina from bauxite via the Bayer process . For lowering costs , future research should include study of leaching at lower temperatures under atmospheric pressure and alternate aluminum nitrate decomposition methods .

Jan 1, 1964

By P. H. Mutschler

The Bureau of Mines studied the Chattanooga Shale to determine the quantity and quality of the uranium resources present and to assess specific environmental effects of mining the shale. Geologic data and chemical analyses, mainly concerning a 12-county area of Tennessee, were compiled from previous published and unpublished reports. Uranium resources in the Gassaway Member of the Chattanooga Shale in this 12-county area were estimated to be between 4.2 and 5.1 million tons, contained in 76 to 91 billion tons of shale. These figures represent inground tonnages and do not allow for mining or processing losses. Depending upon efficiency of mining and processing systems, enough uranium could be available to satisfy a large part of the cumulative domestic and world demand through the year 2000. A model was developed which assesses the total tons or acres of shale to be mined if the Gassaway Member were to satisfy 1 percent of the United States demand for uranium in 1991. This partially demonstrates the environmental impact of mining the shale and is easily factorable to any specified demand.

Jan 1, 1976

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By Volker Weiss, George Sachs, AE. P. Klier

PHYSICAL chemistry contributes to the understanding and efficient operation of hydrometal-lurgical processes in many ways, among them by providing quantitative answers to the following questions. 1) Can a given chemical reaction or process be made to operate and. if so, under what conditions? 2) what are the' factors which determine the rate of the reaction and how can this rate be regulated in practice? Thermodynamics attempts to answer the first of these questions and kinetics the second. The answer

Jan 1, 1958

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981