Search Documents

By C. Blawert

In spite of various corrosion studies on HPDC AZ91, there is no clear indication which microstructure gives the best corrosion performance. The skin with its fine microstructure is sometimes reported to have the best corrosion resistance, but there is no clear definition of the skin. If the skin is the outermost part of the casting and nothing is removed from it, then it is contaminated and the corrosion resistance is low. If the outermost skin is removed (about 25 µm) then a better corrosion resistance can be obtained. However this does not automatically mean that there is no other region in the bulk of the casting which could have a similar or even better corrosion resistance. Indeed, the corrosion measurements including potentiodynamic polarization and long term electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin about 100 pm thick. The thickness of this region is more or less independent from the thickness of the casting section. The surface region is free from any dendritic grain growth which influences the amount and distribution of the 13-phase and therefore the distribution of the most important alloying element Al. This could explain the different corrosion behavior. Further reason can be found in the enrichment of some impurities such as Fe in the near surface.

Jan 1, 2006

By S. Cotten

The regulations for current coal mine refuge alternative (RAs) require that there be sufficient life support to sustain survival of the maximum number of RA occupants for a minimum of 96 hours. This minimum duration assumes that rescuers can access the RA through the mine within four (4) days of the onset of the mine emergency. But what if mine rescue teams cannot reach the miners within the RA before the RA air supply is severely limited or exhausted? What could be done to extend the duration of the RA life support capability into the 97th hour and beyond? In addition, what might be done to enable more rapid rescue of the miners if they could not be reached through the mine in a timely manner? This paper describes a systems approach to address the potential need to extend the duration of RA life support beyond current design limits. New capabilities that need to be developed in advance of such a dire need include more reliable emergency communications, highly mobile and efficient drilling rigs, enhanced directional drilling techniques, and a standardized RA external life support interface along with RA internal design modifications to accommodate use of an external supply. The following sections describe the need, intent, and technology gaps associated with each of these capabilities. Government agencies and the mining industry should consider initiation of a program to investigate, design, and develop effective means of extending the current 96-hour time restriction on coal mine refuge alternative life support. The development process should begin with a focused study to refine the overall operational concept, investigate the current state-of-the art of critical technologies, identify specific technology development priorities, and make recommendations for a development program to provide in an organized, efficient, and timely manner a solution for extended refuge alternative life support and occupant rescue.

Jan 1, 2011

By John W. Lane

Climax Molybdenum Company, a Division of American Metals Climax, Inc., operated a hydrometallurgical plant* at Climax, Colorado from August 1966 through August 1968 to recover molybdenum from a mixed oxide and sulfide ore. The ore treated for this addition to the existing plant contained sufficient Molybdenite values to be mined for Molybdenite recovery alone, so that the oxidized molybdenum recovery could be regarded as a byproduct operation. Climax is located at an elevation of 11,300 feet. All process equipment, except thickeners, was enclosed in buildings. Annual snowfall is approximately 250 inches per year. Paved highways and rail service to the plant are maintained and kept open all year. Most of the employees live in the town of Leadville, which is approximately twelve miles from the plant site. The sulfide flotation plant handles 40,000 to 45,000 tons per day of ore. The mine is one of the world's largest underground mines.

Jan 1, 1971

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

By J. A. Russell

MR. M. W. Boom: I would like to congratulate Mr. Russell on his fine paper. One very good point which has always appealed to me is the smooth working of a steam hoist as compared with electrical. He does not mention the steam hoist at Springhill which has been working there for a good many years. MR. S. R. NEWTON: I have read with a great deal of interest the paper presented by Mr. Russell on the development of haulage engines in the mines of the Dominion Steel & Coal Corporation. He is to be congratulated on having produced a comprehensive article showing, step by step, the various improvements that have been made over the years in the design of such engines. I am quite in accord with Mr. Russell's statement that the positive tooth clutch can have too many teeth, and also that the method of driving a sliding clutch hub of any design should be by means of a hexagon or octagon on the shaft. Where the clutch hub does not of necessity slide on the shaft it can be pressed on and keyed to the shaft in the normal manner. With regard to the 'Cramp' internal-expanding jaw-type clutch, while it is true there are more moving parts than with the clutch consisting of a ring with internal cut teeth and a driver having a fewer number of teeth as .described by Mr. Russell; there are compensating advantages to the internal expanding jaw-type of clutch. The V shaped profile of the teeth permits of engagement of the clutch with very much less 'jockeying' of the drum. This is particularly the case in vertical-lift mine hoists, where it may be necessary to engage and disengage the clutching mechanism at frequent intervals.

Jan 1, 1944

By H. Clare Horwood

"Two structures, a fracture zone and a shear zone, contained the two orebodies that yielded all the ore mined at the Gold Eagle mine. The orebodies are known as the Gold Eagle vein and the No. 1 shear zone. Both structures occur close to contacts between Timiskaming sediments, Algoman diorite, and later Algoman granite-granodiorite. The structures were produced by compressive forces from a south direction acting in the southern part of the McKenzie-Gold Eagle stock and in a cylindrically shaped inclusion of Timiskaming sediments.The mine, which exhausted its ore reserves and ceased operations in September of 1941, is on the east side of Mackenzie island, in the centre of Dome township in the Red Lake area.The Gold Eagle vein was located during the summer of 1933 by a surface exploration programme carried out under the direction of Alex Gillies. Sub-· sequent diamond drilling and underground exploration led to the installation of a mill, which came into production in October of 1937. The No. 1 shear zone was discovered and explored later from a drive on the 500-foot level. The mine produced a total of 40,204 oz. gold and 19,157 oz. silver from 223,628 tons of ore hoisted (180,095 tons milled) during its 4 years of mill operation.GENERAL GEOLOGYThe ore-bearing structures trend S.61°E. across Timiskaming greywacke, Algoman diorite, and later Algoman granite-granodiorite. The greywacke is a large, cylindrically shaped mass that is separated from the mai~ mass by the later intrusives. It is a massive, light-coloured, quartzose variety that has been recrystallized by the enclosing granite. The diorite and the granite-granodiorite are early and late components of the McKenzie-Gold Eagle stock. The diorite, which is a porphyritic rock containing large crystals of andesine-labradorite surrounded by hornblende, was injected early in the Algoman period. It was intruded and in large measure surrounded by the later granite-granodiorite. This rock varies from a granodiorite near the mine to a granite in the centre of the stock. All three intrusions are massive and homogeneous."

Jan 1, 1954

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By Abdulhadi H. M, Soliman S. A

The Western Desert of Egypt is a part of the arid Great Sahara of Africa which extends from the Nile Valley in the east to the Atlantic Ocean in the west. It is covered by a sedimentary sequence of Mezozoic and Teriary rocks. Recently this part of the country (about 65% of its surface area) has attracted an increasing attention in the plan of finding new agricultural and industrial communities outside the crowded Nile Valley. The plan aims to reduce the high population density in the narrow Nile Valley and to cover a considerable part of the increasing food demands in the country of Egypt. Accordingly, the groundwater exploration work in the Western Desert has been remarkably increased in the last decade, however it is still limited compared with the vast area of the Desert. The present work is a part of the groundwater exploration in the 6th October City, a new community located at 40kms west of Cairo. The rock exposures belong to a sedimentary stratigraphic section starting from the Cretaceous in the east to the Pliocene in the west. The Cretaceous outcrops due east are attributed to an almost N-S uplift and forms a thick massive limestone plateau which separates the present area from the Nile Valley. The Teriary section in the west have alternations of different porous formations such as the sands and sandstones which may acquire a good potentiality of groundwater resources. The previous groundwater exploration work included combined geological and geophysical investigations followed by exploration drilling. Although the area lies directly to the west of the Nile Valley, the discovered groundwater is saline and located at deeper reserviores compared with the groundwater in the Nile Valley. This groundwater was described as marine fossile water by the oil companies working in the Western Desert. From the geological point of view, it is believed that the Cretacious massive limestone plateau, in the east, roots to a depth which far exceeds the groundwater levels in the Nile Valley and acts as an impervious barrier between the aquifers in the Nile Valley and the area under investigations.

Jan 1, 1988

By G Solly, S Parsons, P Leevers, S Ni

Hematite ore has been mined in the Southern Middleback Ranges as blast furnace feed for the steelworks at Whyalla, by what was then BHP, since 1991. With the floating of BHP Integrated Steel as OneSteel in 2001 and the subsequent loss of key mining personnel, breakdowns in grade control methods and procedures occurred. These were compounded by changes in orebody characteristics and grade distribution leading to poor reserve recovery and poor grade control, both which resulted in loss of control of ore specification and severe deviation from the mining schedule. As a result, a total review of grade control, mining method and scheduling procedures was undertaken as well as a review of contractor quality assurance. It was found that sampling methods were poor and unrepresentative, grade control blocking processes were outdated and did not reflect the geology of the deposit, the ore mining method was outdated and did not respect the geometry of the orebody, reconciliation methods were being completed globally and were not reflective of individual areas of the deposit, and that deviations from the mine plan were occurring due to access to high-grade areas outside the schedule in order to bring stockpiles back on grade. Based on these findings, updated sample splitter systems were fitted to drill hole rigs, double bench sampling was implemented (2 + 4 m samples as opposed to 1 + 8 m sample) and a three-dimensional cellular grade control system introduced to better reflect the geology and orientation of the deposit. At the same time ore mining was changed from front end loaders mining on 8 m benches to excavator mining on three lifts on 8 m benches; this aided selectivity and respected the geometry of the orebodies aiding cleaner recovery. Reconciliation is now completed on a blast-by-blast basis, which allows for quick and easy identification of poorly performing areas of the resource model that can then be incorporated back into resource model updates. Regular daily and weekly meetings are also held with emphasis on the mining schedule to ensure no deviation from the schedule in the long term. These improvements have resulted in a lift in reserve recovery both globally and locally associated at the same time with improvement in grade.

Jan 1, 2005

By D. J. Turk

Faced with decreasing production from the gold heap leach operation, Robinson implemented a drilling and blasting program on the leach pads in 1993. This program offset some of the negative effects of low ore permeability and short circuiting of leach solution that resulted in lower than optimum recoveries. The drilling and blasting program created new solution flow paths and increased gold recovery. Production and pulp assays at depth intervals, prior to and following drilling and blasting, reveal the degree of short circuiting and benefits of the program.

Jan 1, 1995

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By Katarína Gáborová, Marcela Achimovičová, María Florencia Márquez‑Zavalía, Jaroslav Briančin, Oľga Šestinová, Pavel Škácha

In this paper, the structure, morphology, chemical composition and leaching of naumannite ( Ag2Se) were studied. Mechanical activation of Ag2Se in a planetary ball mill resulted in increasing its specific surface area. The influence of milling time on the particle size was studied by particle size distribution analysis and scanning electron microscopy. The leaching kinetics of non-activated and mechanically activated samples in 3.5–7.9 mol/L HNO3 solutions were examined. Subsequently, the effect of leaching temperature in the range of 25–50°C on the recovery of silver from mechanically activated naumannite was documented. The maximum yield of silver 94% was achieved after 120 min of leaching in 7.9 mol/L HNO3 at 50°C for the sample mechanically activated for 30 min. Based on calculated activation energy values from the Arrhenius equation, a mixed leaching mechanism consisting of diffusion and surface chemical reaction as the rate-controlling steps of the solidliquid reaction was assessed.

Mar 4, 2023

By Joe D. Mitzel

The Indian Head fine has been in existence since 1922. For over 56 years there have been North Dakota people mining coal at this same location. The area affected will fit inside a circle 5 km in diameter, and the coal is lignite. The seam thickness has varied from 2.4 m to 3.65m, and the overburden from 6 m to 30 m in depth. me Lignite coal which is being mined at the Indian Head Mine is from 15.8 x l0 6 to 16.7 x 10 6 J per kg; it has a moisture content of 33 to 38%; an ash content of 5 to 10%; and a sulfur content of from 0.5 to 0.7%. The moisture content and the fact that we crush the coal co a top size of 14 cm x 0, are two of the characteristics or the product which cause it to freeze and remain inside of the railroad cars on the slope sheets. The market for the coal initially was almost entirely local coal sales. That is, coal was sold to people in the area who used the lignite to heat their homes, stores, offices, schools, and churches. Back in the early 1920's, there were no stoker-fed boilers, or pulverized fuel boilers, as we have in today?s marketplace. Basically, all of the coal was sold as lump coal, pieces about 30 to 35 cm square, to be used in furnaces: and nut coal with a top size of about 7.5 cm to 10 cm to be used in the old kitchen cookstove. All of the coal fines, less than 5 cm, were screened out and layed onto a pile. There was no market for the smaller sizes of the lignite coal. It has been our experience that when the coal is in lumps or chunks larger than 7.5 cm to 10 cm, there is a very slight possibility of freezing. That is the chunks themselves freeze, but by their nature, they do not cling to one another or form large masses of frozen material which are difficult to remove from the slope sheers of the railroad cars.

Jan 1, 1980

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

By Benoit Bissonnette

"The need for production of a competent fill was recognized early by the project partners. Consequently, a 4000 Ud paste fill plant was constructed and commissioned in early August 1994.In order to fine tune the process without risk to the underground workings, a closed pumping loop was devised on surface. After two months of this exercise, the first underground slope was filled according to specifications obtained from the pilot plant trials.This paper will focus on the operational problems encountered and the solutions adopted so far, and on a comparison between expected and actual fill production and characteristics.RésuméLa nécessité de produire un remblai de propriétés mécaniques suffisantes a été rapidement reconnue par les partenaires du projet. Conséquemment, une usine de production de remblai en pate, utilisant les residus du concentrateur d'une capacité de 4000 t/j a été construite et l'opération a débuté au mois d'aôut 1994.Dans le but de roder le précedé sans mettre en danger les installations souterraines, l'usine a été testée dans un circuit de surface. Après deux mois d'essais, le premier chantier souterrain a été rempli avec du remblai en pate selon les specifications dérivées de l'usinage pilote.Cet article présente les problemes d'opération rencontrés et leurs solutions, en plus de faire une comparaison entre les résultats prévus et ceux actuellement obtenus sur la production et sur les charactéristiques du remblai."

Jan 1, 1996

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012