Search Documents

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

Validation and Simulation of Optimised Compressive Crushing Ores and aggregates are used in countless applications all around in the society. The frequent and escalating usage of these natural resources requires efforts aimed at not only making do with what is available, but also undertaking actions to improve the production yield and the processes involved. This strive to improve the performance and efficiency of existing crushers and crushing processes has brought about research concerning optimisation of crushing plants as well as theoretical optimisation of crushing. Previous work shows that different applications and different materials require different compressive crushing in order to accomplish a theoretically optimal size distribution. These optimisation results, obtained by genetic evolutionary algorithms and evaluated with so called fitness functions, convey the theoretically optimal number of compressions and their corresponding compression ratios. Presented in this paper are thus some laboratory crushing tests, which are conducted in order to validate a set of previously optimised crushing sequences. More specifically, interparticle crushing sequences are carried out in a Piston-die testing equipment, where samples are sieved between each compression. The subsequent analysis of these results shows good correlation with model predictions, which combined with a comparative study between presented optimisation results and measured data from a real crusher indicate a significant potential for improvement. However, before redesigning crushers according to what is theoretically optimal, the resulting impact as well as the effects on the outcome of a crushing plant must be examined. Crushing plant simulations using the software PlantDesigner« are consequently performed. Models of existing crushers are altered, resulting in changed particle size distributions from some of the crushers in a crushing plant. Thence, it is concluded that significant gains can be made in terms of capacity, process yield and energy consumption.

Sep 13, 2010

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By E. Hardwick, K. C. Sole, Y. Jurrius

"The Luilu cobalt plant at Kolwezi, Democratic Republic of Congo, has been operating since the late 1950s, using a conventional precipitation flowsheet for removal of impurities from the cobalt process stream. Most impurities are, however, incompletely removed using this technology. Copper and zinc, both of which quantitatively deposit at the cathode in the cobalt electrowinning process, are two of the main impurities contaminating the cobalt metal product. Ion exchange offers a modern approach to removing these impurities from the cobalt advance electrolyte.Following a laboratory testwork programme to identify a suitable ion-exchange system, an on-site pilot-plant trial, treating 1500 to 3000 L/d of electrolyte, was operated for a period of six weeks to optimise the operating conditions and to determine full-scale design criteria. Copper removal was carried out using a fixed-bed lead-polish configuration with the Lanxess iminodiacetic acid resin, TP 207. Zinc removal was subsequently carried out in a similar configuration using the Lanxess aminophosphonic acid resin, TP 260. The optimised system proved capable of removing both copper and zinc from 20 to 30 mg/L to <1 mg/L from plant electrolyte containing ~20 g/L Co. Selective elution allows co-loaded cobalt to be returned to the main circuit and value to be obtained for the copper impurity. The process shows operational and economic advantages over the traditional flowsheet. Full-scale implementation of the developed process is in progress and some design considerations are discussed."

Jan 1, 2014

By Rubén J. Sánchez Rodriguez, Carlos M. Fontes Vieira, Carlos E. Gomes Ribeiro

Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

Jan 1, 2015

By A. B. Kinzel

THE year 1936 has been an eventful one in the iron and steel industry. Renewed industrial activity has brought with it many new problems. These problems have generally involved the question of increasing capacity without sacrifice of economies and quality developed in the less active previous years. The nature of the iron ore used and the effect of its porosity and other physical characteristics on the capacity of the blast furnace has been reviewed by the U. S. Bureau of Mines. The whole question of handling raw materials and methods of charging furnaces has been intensively studied, with the result that capacity has been in- creased without affecting the quality of

Jan 1, 1937

By Rossiter W. Raymond

The manufacture of ferromanganese in the blast furnace having been the subject of considerable attention in the Institute, I beg to put on record a contribution to the discussion from a quarter hitherto not directly represented, namely, the St. Louis furnaces, near Marseilles in France, belonging to a company of which M. Jordan, a member of the Institute, is Managing Director. These furnaces commenced in 1862 to manufacture specular pig (fontes facettes) containing from three to six per cent. of manganese. In 1864 the regular production of spiegeleisen (fontes miroitantes), containing seven to ten per cent. of manganese, was inaugurated. At that time the Rhine was the only locality of this manufacture, and the Bessemer works of England and France obtained from Gernlany all their spiegel. From 1864 to the present time, the St. Louis furnaces have been advancing steadily the percentage of manganese in their product. From ferromanganese of thirty per cent. they had arrived, about two years ago, at a product containing seventy to seventy-five per cent., and for some time past they have been turning out what, as M. Jordan remarks, may fairly be Termed fonte de manganese, or manganese pig, instead of iron, since the percentage of iron it contains is not more than 8.5, while the percentage of manganese is 85, or ten times as great. This very high grade material has a peculiar appearance, entirely different from that of ordinary cast iron or spiegel. It is granular, and steely gray in color. The following analyses, communicated to the Sociètè des Ingenieurs Civils, by M. Jordan, show the composition of various products of the St. Louis furnaces:

Jan 1, 1879

By Frederick McNeill, John Harper, Mahmood Khwaja, Shawn Lavoie, Timothy Cloughert, David Polcari

City of Manchester, NH, is implementing a 20-year plan to control and significantly reduce overflow of its sewer system. The long-term control plan had called for large scale box culvert installation through downtown Manchester. The City and the project team evaluated, and eventually selected, tunneling as an alternative to mitigate construction related impacts for open trench approach. This paper provides an overview of the alternative evaluation process; discusses the development of the preliminary design for the 12,000 feet long, 12-ft internal diameter tunnel, including plan and profile selection, subsurface conditions, drop shafts and the anticipated packaging of the separation areas.

Dec 1, 2022

In the estimation of recoverable resources, geostatistical techniques such as Multiple Indicator Kriging require a change of support correction to derive theoretical recoveries based on an assumed level of mining selectivity. The change of support models most widely used in practice entail model based generalized corrections either on a global or local basis. Examples include the affine and indirect lognormal methods. Change of support corrections derived empirically through short-scale conditional simulation realizations often show notable differences compared with theoretical corrections determined using model variogram parameters. The existing changes of support models are reviewed and an alternative method is proposed.

Jan 1, 1999

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Lorraine Kent

Excessive floor and side deformation are major problems in deep coal mine entries in Europe, and in particular in the UK where rockbolt support is used at depths of working of around 3000 ft. This has major economic and safety implications for the industry resulting in the potential for sidewall instability, disruption to mine infrastructure, (belt conveyors, floor mounted transport systems and powered supports), and the requirement to safely manage excavation of large quantities of floor material. European research aimed at improving deformation control is described. The outcomes include innovations in support systems, materials and installation practices, as well as better methods for predicting and monitoring deformation levels. As coal mines get deeper, some entry deformation is inevitable, and methods for mechanised removal of floor lift and repair of sidewalls have been developed to allow production to continue as mining clearances are re-established.

Jan 1, 2014

By C. K. Leith

WE face the postwar problem of the use of minerals as sanctions to control the armament and the re-armament of the Axis powers at the source, minerals being the raw material of armaments. That is the subject of today&apos;s discussion. It is one thing to talk about controlling minerals in the interest of rearmament, and it is another thing to put any such ideas into effect. A provision for min- eral sanctions-not by that name but under broader terms-was contained in Article 16 of the League of Nations, and an attempt was made to apply min- eral sanctions when Italy cut loose in Africa. That was a failure because the plan was badly thought out. They did not have the right minerals included in the list. Also, they did not have the machinery set up at all. Somebody said to the League of Nations: Let&apos;s apply the sanction, and it was assumed that that was all that was necessary. It turned out to be a rather sad perfor- mance. However, that certainly cannot be taken as an example of what will happen if a properly thought-out pro- gram is adopted.

Jan 1, 1944

By Wm. H. Woodhead

Improved methods of mining have accompanied the introduction of mechanical loading, of which there are a great many varieties, but this multiplicity of mining brings new problems and greatly increases the importance of managing over a few years ago. Few mines operating today have been opened with the intention of mechanizing throughout. The problem of mechanization is to change over a mine heretofore operated by hand methods and to select machinery that will fit the old system with the least number of changes, the aim being not to disrupt or to completely change the original plan. The organization of mechanical and electrical forces is a problem in mechanical loading, and each individual mine presents its own problems. Plans which may succeed in one mine may fail in another and upon the management rests the responsibility of deciding the best method in each case.

Jan 1, 1930

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By L. A. Weakly

The Viburnum ore trend is the largest, single known ore body of lead in the world. Four well-known mining companies operate in the trend, which is approximately 64 km (40 miles) long and up to 610 m (2,000 ft) wide, located some 121 km (75 miles) southwest of St. Louis, MO. Total production from the mines for 1979 was 33 kt/d (36,000 tons) of ore or 472 kt/a (520,350 tons) of lead and coproduct metal. The district is the number one producer of lead, providing 90% of the United States&apos; output with its coproducts, zinc ranking second, and copper and silver both ranking sixth in total US output. Mining is done in a stratiform deposit approximately 305 m (1,000 ft) in depth with the host rock principally dolomite. Ore is mined in large open stopes by the method commonly referred to as room-and-pillar mining. Mining methods and equipment are fairly similar, with the mines classified as trackless, all mining equipment operates on rubber tires. This paper will present a description of the different methods and equipment used to move ore from the active heading underground to the ore shaft for hoisting to the surface. Basically, three methods are incorporated: front-end loader and truck haulage combination; front-end loader and truck, with main line track haulage combination; and front-end loader and truck, with conveyor haulage combination. The logistics of each system, such as method of use, equipment specifications, ore handling rate, and those cost figures that could be made public, will be included.

Jan 1, 1983

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016