Search Documents

By G. W. Binkley, R. E. Collins, G. K. Dumbauld

A mathematical analysis has shown that the primary factors affecting the deposition of cement in unfractured perforations during squeeze-cementing operations are: the properties of the cement slurry, the geometry of the perforations, and the filtration time. The validity of the analysis has been substantiated by laboratory investigations. The information presented in this paper makes possible the prediction of the rate of deposition of cement in and about unfractured perforations under given squeeze-cementing conditions, the proper filtration time to control the amount of deposition to any desired value, and the deposition properties needed in cement slurries to restrict to any desired degree the formation of nodes of cement .Solids inside the casing. INTRODUCTION The deposition of solids against a permeable medium by the process of filtration is an important property of a cement slurry. General recognition of the role of filtration in the use of cement in wells is evident in view of the fact that several patents on low-water-loss cements have been issued during the past few years. In the conventional, high-pressure squeeze-cementing technique, a large volume of cement slurry is usually displaced into the area surrounding the perforated interval after the formation has been fractured hydraulically.&apos; Near the end of the job, the pumping rate is slowed or stopped intermittently in an effort to obtain a high pressure in the wellbore. The way in which a high pressure is obtained is not understood thoroughly. but it is be- lieved to be caused by the deposition of a rigid mass of compacted cement particles either in the fractures of the formations or inside the casing opposite the perforated interval. In a method of squeeze-cementing introduced several years ago, a small amount of cement slurry is squeezed into the perforations at a low pressure to avoid fracturing the formation. The filling of the unfractured perforations with cement particles by the process of filtration is important to the success of this technique. Early in the development of this low-pressure squeeze-cementing technique, laboratory and field-size experiments showed that conventional, neat cement slurries were unsatisfactory if the tubing was extended into or through the perforated section of the casing. The extremely high filtration rate of neat cement slurries caused the deposition of a compacted mass of cement inside the casing and made it impossible to remove excess cement by reverse circulation and difficult to withdraw the tubing. Because the need for cements with a reduced filtration rate was obvioils and urgent, modified cements containing 12 per cent bentonite were used until research was completed on modified cements containing 25 per cent bentonite.< These modified cements were useful in the solution of the immediate problem, but the following questions remained unanswered: (I) what is the optimum filtration rate of cement slurries for this application, (2) how long should the squeeze pressure be applied. and (3) how great are the effects of squeeze pressure and well temperature on the rate of deposition? Furthermore, the relationship of the filtration properties of cement slurries to the dimensions of the perforations and the wellbore was unknown. In order to obtain information relative to these basic considerations, a systematic evaluation of all the factors involved in the deposition of Cement during low-pressure squeeze-cementing operations was initiated. Although the work was directed toward an evaluation of the factors influencing the deposition of Cement in the low-pressure squeeze-

By Hugh D. Olmstead

Typical operations necessary to develop oil and gas reservoirs are reviewed, including exploration, drilling, cementing, completion, work over, sand control, stimulation, enhanced recovery and production. The role of industrial minerals in these operations is described. Some of the opportunities and problems affecting increased use of industrial minerals in drilling and stimulation are discussed.

Jan 1, 1983

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By A. D. Davis

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well defined drainage in a heavily mineralized area of the northern Black Hills. The basin contains numerous inactive and abandoned mines as well as a currently active heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer and thus can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted, and two abandoned mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 1997

By Szwedzicki T

In recent years substantial advances have been made in the field of geomechanics. Staff at the Western Australian School of Mines (WASM) are keen to see that such advances continue and that the mining industry in Australia can take full advantage of such developments in a timely manner. WASM views mining geomechanics in its broadest sense, as being concerned with the characterisation of the physical properties and the behaviour of earth materials (soil, rock and water) and openings as mining proceeds. Aspects such as, soil and rock improvement techniques for difficult site conditions and the rock breaking processes, are also considered to be an integral part of mining geomechanics. This paper indicates the inter-relationships between the various areas within the field of geomechanics and the strong reliance of all of these areas on site specific engineering geology.

Jan 1, 1992

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Dan Wang, Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Hongwei Cheng, Changyuan Lu

The preoxidation of the ore has a profound significance to the concentration, separation and purification of nickel and copper from the lean complex ore. In this paper, the natural Ni-Cu sulfide mineral samples under the elevated temperature condition in air were investigated, as well as under isothermal condition at 600 oC in air. The mineralogical characterization was studied using XRF, ICP and the Rietveld method. The oxidation behavior and the element migration of the Ni-Cu sulfide ore were studied by XRD, SEM-EDS and TG. The XRD Rietveld method was successfully developed in the phase identification and quantification of this complex ore powder sample. The oxidative intermediates (Cu/Ni-ferrite) were detected by XRD, and the process of the element migration was obviously revealed by the line scans using SEM-EDS. It is the preoxidation of this mineral that provides guidance for the extraction of valuable metals from low-grade Ni-Cu sulfide ores in the future.

Jan 1, 2015

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By Navid Bahrani

Introduction ? Today?s economic market is motivating underground mining companies to increase development advance rates and enhance their NPVs. ? For example, block cave mining involves development of kilometers of drifts with multiple pillars. ? The cyclic nature of drill and blast, and its inherent tendency to damage the surrounding excavation rock mass and increase support demand often result in poor advance rates ? This has motivated mining companies to replace the conventional drill-and-blast as the main excavation method with alternative methods such as mechanized excavation. ? There is little experience with mechanized or non-explosive excavation methods in hard rock metalliferous underground mining.

Oct 1, 2010

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By Eric Jacobs

"Building and operating tunnels has been a highstakes endeavor in terms of costs, complexity, safety and impact on contractors, owners and the public for a long time. There are many variables that need to be closely monitored and managed to construct a tunnel on-time, on-budget and safely. Once built, there are also many elements that need to be monitored and managed to operate a tunnel safely and efficiently.Fundamentally, the risks to the safe and efficient construction and operation of a tunnel are a function of the degree of harm and the likelihood of the harm occurring. From a cyber security perspective, risk assessments used to inform decision makers and support risk responses are typically based on identification of relevant threats; internal and external vulnerabilities; the impact that may occur given the potential for threats to exploit vulnerabilities and the likelihood that harm will occur. This article focuses on creating awareness of vulnerabilities associated with technology used in tunnel construction and operation and some of the challenges associated with remediation of these vulnerabilities. As we all know, technology has been evolving at an accelerating pace and infiltrating every aspect of our lives in new and often exciting ways. In the world of tunneling, sensors and systems that provide position and time have become accurate, rugged and cost-effective enough to come out of the research labs and into the equipment and systems used every day. There are many opportunities to employ connected computing devices and sensors to costeffectively capture, integrate and analyze key data with minimal latency to manage risk better, improve safety and avoid surprises."

Jun 1, 2019

By J. S. Bays

Industries are challenged to meet increasingly stringent regulations for selenium and metals. Cost-effective treatment is required to minimize the economic impact of environmental compliance. Low-cost biological treatment of selenium can be achieved passively using biochemical reactor cells composed of natural organic media components such as wood chips, sawdust, hay, composted manure, and peat. The reactor cells create an anaerobic microenvironment for biological reduction and sequestration of selenium and other metals. Biochemical reactors can be combined with constructed wetlands for flow equalization and to remove the organic byproducts in reactor cell outflow. Passive treatment reduces capital cost and operational effort compared to more expensive and complex physical and chemical treatment. Recent pilot and full-scale projects by mining companies and by the US Bureau of Reclamation demonstrate that passive treatment can achieve compliance with selenium concentrations over a range of flows and environmental conditions. Case histories of passive selenium treatment systems and their key findings are provided, and prospects for future applications are summarized.

Feb 27, 2013

By Charles H. White

+1HARVARD UNIVERSITY, CAMBRIDGE, MASS. The equipment of a laboratory in which students are to be trained for practical work in metallurgical chemistry presents many difficulties not encountered in the fitting up of a commercial or works laboratory. At an industrial plant the chemical work required usually demands the frequent repetition of a comparatively limited number of methods. In a steel-works laboratory, for instance, by far the larger part of the work consists in making determinations of the usual impurities found in iron and steel; at a smelter the great bulk of the work is confined to the analysis of ores, slags, mattes, and fuels, which involve the frequent application of perhaps not more than a dozen different methods. In a laboratory of this character, therefore, those operations most frequently applied may each have a certain section set apart and fitted permanently with such apparatus as best facilitates the carrying out of this one operation. The work of a commercial or custom laboratory is perhaps more varied than that of a works laboratory, but the couditions are similar in these respects, that there is usually no great need for economy of space, and that a few skilled workmen are employed to carry the determinations through from beginning to end without interruption. On the other hand, the laboratory of a technical school should be planned on such a scale that a comparatively large number of students may work at the same time, and each desk should be equipped for general metallurgical analysis. In most institutions for technical education the student&apos;s program is so arranged that his day is divided among several subjects in the course of study; only a few consecutive hours being devoted to one subject, or spent in one laboratory. Therefore, those appliances should be provided that render possible the safe continuation of such processes as

Jan 1, 1905

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By Mark Van Dyke, Ted Klemetti, Joe Wickline

"The identification and mitigation of adverse geologic conditions are critical to the safety and productivity of underground coal mining operations. To anticipate and mitigate adverse geologic conditions, a formal method to evaluate geotechnical factors must be established. Each mine is unique and has its own separate approach for defining what an adverse geological condition consists of. The collection of geologic data is a first critical step to creating a geological database to map these hazards efficiently and effectively. Many considerations must be taken into account, such as lithology of immediate roof and floor strata, seam height, gas and oil wells, faults, depressions in the mine floor (water) and increases in floor elevation (gas), overburden, streams and horizontal stress directions, amongst many other factors.Once geologic data is collected, it can be refined and integrated into a database that can be used to develop maps showing the trend, orientation, and extent of the adverse geological conditions. This information, delivered in a timely manner, allows mining personnel to be proactive in mine planning and support implementations, ultimately reducing the impacts of these features. This paper covers geologic exploratory methods, data organization, and the value of collecting and interpreting geologic information in coal mines to enhance safety and production.The implementation of the methods described above have been proven effective in predicting and mitigating adverse geologic conditions in underground coal mining. Consistent re-evaluation of data collection methods, geologic interpretations, mapping procedures, and communication techniques ensures continuous improvement in the accuracy of predictions and mitigation of adverse geologic conditions. Providing a concise record of the work previously done to track geologic conditions at a mine will allow for the smoothest transition during employee turnover and transitions. With refinements and standardization of data collection methods, such as those described in this paper, along with improvement in technology, the evaluation of adverse geologic conditions will evolve and continue to improve the safety and productivity of underground coal mining."

Jan 1, 2019