Search Documents

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By AIME AIME

OUR own Institute of Metals and Iron and Steel divisions cooperated with the Iron and Steel Division of the American Society of Mechanical Engineers, the American Welding Society, and the American Society for Steel Treating in a busy week at Cleveland. The morning sessions were held at the Hotel Cleveland and the afternoon ones at the Auditorium, where the metallurgical exhibition under the auspices of the American Society for Steel Treating not only occupied the arena of the Auditorium but completely filled the huge adjacent Annex. In the intervals of sessions the members thronged the exhibits but in the evenings the local attendance was so great that if the crowds had been any larger it would have been difficult to see the exhibits. With so many firms, both producers of metals and of equipment accessory to their production and use, it would be impossible to mention them -all and unfair to single out a few, since no two individuals' judgment would coincide as to relative interest and importance. In any case an exhibit is a thing to be seen rather than described, and these were well worth seeing.

Jan 1, 1929

By J. Gordon Parr, D. A. Whitaker, G. A. Yorko

High purity alloys of zinc with 25 per cent to 50 per cent aluminum, have been prepared. Mechanical properties of the as-cast and heat-treated alloys have been related to constitution, determined by x-ray diffraction and microscopic methods. Investigations include the effects of aging and of small nickel additions on the properties of the alloys.

Jan 1, 1960

By L. C. Noakes

Despite a long history of mining. Australia had no Commonwealth organization dealing specifically with the mineral industry until 1946, when the Australian Bureau of Mineral Resources, Geology and Geophysics was established. Once formed, this new organization quickly expanded to include a Mineral Economics Section, which was established in 1947. Australia's slowness to develop a Federal bureau for the mineral industry can best be explained in the light of her political history. From a group of British crown colonies, Australia evolved into six sovereign states which had no unified federal government until they formed the present Commonwealth in 1901.

Jan 1, 1970

By R. Scheepers, J. E. Misiewicz, A. C. Fitzgerald

Discussion by A.C. Fitzgerald of the paper, published in Trans. IMM A, vol.104, 1995, p.B121-B135, is presented together with the authors' response. Fitzgerald points out a number of problems with the idea of mineralising fluids leaving no trace in the large volumes of rock traversed before depositing all minerals of value in a particular horizon or rock type with which the required isobaric or isothermic surface also coincides. He suggested that in the case of the Rooiberg tin deposits, the Lebowa Granites may be batholiths that reached the surface and were capped by sheets of their own volcanics. The authors agree that they had considered a possible syngenetic origin for the stratabound deposits, explain that no conclusive evidence for this could be found, discuss the relative ages of the sediments and volcanics of the Rooiberg Fragment and explain the role of its low-intensity deformation and flat dip in the coincidence of an isobaric-isothermic surface with the lithological stratification

Jun 18, 1905

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2 slags that are typically encountered in the production of manganese-containing stainless steels. A gas equilibration-quenching technique was employed in measuring the activities. Activities of Mn in Pt-Mn alloys were redetermined at 1600ºC, which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600ºC. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient regression models were developed to predict the activities and activity coefficients of MnO in slags at 1600ºC. Keywords: activity, MnO, slag

Jan 1, 2005

By R Burgess-Limerick, D Lynas

A number of standards and guidance materials currently exist to assist equipment designers. The ISO process, however, is a formal process and change often lags behind technology development. In some cases, this may result in weak or ineffective standards that need to be written in general terms to accommodate future technology developments, meaning some standards may only establish minimum requirements and not be overly helpful to equipment designers, in particular when designing for workforce diversity and inclusivity. By contrast, advisory information as issued by various mining regulatory bodies is able to respond more quickly to changes in technology. Standards do however have a safety and productivity focus providing design consistency between equipment manufacturers, a basis for auditing purposes, assistance in mining regulation and compliance, and in the development and application of safety management systems. As an example of challenges facing equipment designers, ISO3411 (2020) provides data approximating the 5th, 50th and 95th percentile of the ‘earth-moving machinery operator population’ for numerous static dimensions relevant to the design of earth-moving equipment. These data are then utilised in ISO6682 (2020) to provide recommendations regarding the location of controls. Attempting to utilise the data provided in ISO3411 (or other sources of static anthropometric data) creates further challenges for equipment designers, in that reference percentiles is problematic for design purposes. There is no ‘5th or 95th percentile operator’ as individuals vary along each dimension (Robinette and Hudson, 2006). Although dimensions have some degrees of correlation, when multiple dimensions are considered, the range of individuals which fall within a given range on all dimensions reduces substantially. For example, only about 82 per cent of individuals in a population will fall within the 5th to 95th percentile ranges for both height and weight. The more dimensions are considered, the smaller the range of people who actually ‘fit’ the description.

Apr 16, 2024

By C. Ernst

The underground operation at Barrick?s Cortez Mine, located near Elko, NV, required the construction of a 12 foot diameter smooth-lined ventilation shaft. Barrick preferred to mechanically excavate from the ground surface without putting people in the excavation and considered blind drilling by Frontier-Kemper Constructors the best option. Design and construction challenges arose throughout both the excavation and lining stages. A large portion of the rock to be drilled was highly fractured. Important risks that were addressed included water loss into the formation, zones of squeezing ground, damage to drilling tools caused by blocky ground and fallout, and potential hazards during cast-in-place concrete lining. Detailed explanations of these challenges and the methods used to overcome them will be described.

Feb 23, 2014

By E. Maltby Shipp

YouR committee's secretary submits the following report, or summary, to the members of the committee, in an endeavor to lay before them a general review of the information so far received and also his own knowledge of the work as carried on at a number of plants, this being done in part to secure further information and suggestions from members and lead to a more effective means of furthering the work of the committee. It is suggested that more detailed data be compiled regarding engineering features involved, and that papers be contributed which will deal with the safeguarding of underground electrical installations. There are few operating companies which have not started a more or less systematic campaign to safeguard their employees from accidental injuries and unhealthful surroundings, but a great deal is to be gained by experience. All may welcome the advice and cooperation of those who have been actively engaged in the work and have demonstrated the results obtainable by organized effort, and it is, therefore, exceedingly gratifying to note the ready assistance and hearty cooperation rendered by the companies that may be truly termed pioneers in the movement. No solution of the safety problem is to be found in a skrict standardization of methods, rules or devices, as the various mining, milling and metallurgical practices present too many conditions differing broadly in general principles, but some standard system embodying principles already proven to be efficient should be created, which may be modified or elaborated to meet specific requirements of each individual company, or to fit working conditions as they exist in the various mining camps throughout the country. An industrial plant is primarily a business undertaking, therefore the economic side of a safety or welfare campaign is of importance. Many small operators have been deterred from undertaking the work by their belief that it involved an expense beyond their means, and one that could not be counterbalanced by greater efficiency or saving along other lines. This idea is generally due to a lack of knowledge of the actual costs of such work, and of the results secured by judicious selection of a method commensurate with the size and nature of the opera-

Jan 1, 1918

By H. N. Egan

Faced with a severe disposal problem of their fines from a coal mine in the heart of the Appalachian Mountains of extreme eastern Kentucky, Eastern Coal Corporation has built a special plant to pelletize the fines into high quality coal pellets meeting the requirements of the metallurgical market. These low-ash, low-sulfur pellets measuring 3/4 x 3/8 in. contain less than 1.5% moisture and have the same stability as raw coal of the same size. Although Eastern Coal is mining 6000 tpd, the company had, until recently, no provision to recover the fine coal which was included with the plant effluent pumped to a 12-acre refuse pond. The pond, impounded behind the coarse refuse dump, rose 15 ft last year and obviously no pond can stand many years at this rate. Limited pond space in this rugged area of steep hills and narrow valleys dictated a revised disposal method.

Jan 11, 1967

By P. Yant, R. R. Sayers, R. D. Lieitch

"PURPOSE OF INVESTIGATIONOf more than 300 bituminous mines examined by Crichton 5 and his assistants in connection with litigation in Indian Creek Valley, Payette County, Pa., only four were found to have alkaline water. That work and many observations from of the authors have shown the general prevalence or acid drainage from bituminous coal mines. In connection with investigations pertinent to coal-mine drainage that are being conducted by the United States Bureau of Mines, it was noted with considerable interest therefore, that a mine in the Thick Freeport bed about 20 miles north of Pittsburgh had no acid water in the workings, As it was thought that this condition might be common to all mines,this condition in this bed most of them were visited, samples of the outflow and from different parts of the mine inside were examined, and such general information as was available was gathered.ACKNOWLEDGMENTSThe authors acknowledge with thanks the courteous assistance of mine officials in connection with collecting the data for this paper, and of the analytical and coal laboratories of the Bureau of Mines for analyses."

Nov 1, 1932

By Sunil Bodakunta, Sreenivasa Rao Islavath

The abstract highlights the importance of determining the optimum line of extraction in continuous miner workings for improved safety and productivity. The study investigates three extraction techniques (diagonal, straight line along strike, and straight line along dip-rise) using 3D numerical modeling. The dip-rise extraction technique is found to be optimal due to lower stress and displacement, leading to a higher safety factor. The research also develops a continuous miner stability index (CMSI) to predict working face stability based on mining depth and pillar width-to-height ratio.

Apr 28, 2022

By L. C. Binon

Exploration budgets are commonly determined by rules of thumb, such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve company goals. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1984

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By P. M. Sandgren, H. Al-Dabbagh

Saudi Company for Precious Metals (SCPM) is jointly owned by the Saudi Arabian state organization Petromin (The General Petroleium & Mineral Organization) and Boliden of Sweden. The company operates the Sukhaybarat gold mine in the Saudi Arabian desert and produces some 80,000 ounces of gold per year by agitation and heap leaching. The discovery, development, and operation of this mine is a success story. After the first drill hole intercepted a gold mineralization in 1983, it took the partners only 8 years to delineate the ore reserve, locate water sources, prepare pre-and final feasibility studies, obtain permits, design, and construct the facilities. Sukhaybarat, which is an open pit mine, started off with a carbon-in-leach agitation plant only, but a heap leach facility was added in the beginning of 1995. Since start of operation in the middle of 1991, a total of 300,000 ounces of gold has been produced in the first four years of operation at a very competitive cost.

Jan 1, 1996

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

By David G. Chedgy

The Meadow River No. 1 Preparation Plant, owned by Sewell Coal Company, a subsidiary of the Pittston Company, was commissioned in the spring of 1974. The plant is designed to process 400 TPH of 5" x 0 raw coal. The 5" x 114'l fraction is processed in a Heavy Medium Vessel with the 114 x 28M reporting to Deister Tables for cleaning. The 28M x 0 fraction is cleaned in flotation cells, with the froth going to clean coal vacuum filters and the tailings to a static thickener where the underflow is reclaimed on Refuse Filters prior to disposal. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the noise exposure in that particular environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: [ ]

Jan 1, 1976

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

By Gabsoo Kim, Rulin Yang, Dave Kay

Blast vibration data, such as PPV are usually scattered. In many cases, plots of PPV versus the charge weight scaled distance are so scattered that useful trends from different blast designs cannot be identified. The scattering of the data may be attributed to the inaccuracy of the PPV measurement, the definition of the scaled distance from a multiple-hole production blast, and the measurement of distances and charge weights. The error from vibration measurements is one of the major contributors to the scattering of the plots. If accurate monitoring is conducted, improved design options may be identified. This paper documents two case examples that compare different vibration sensor couplings. The first case shows mounting accelerometers at spots that protrude from the ground, compared with the sensors that were mounted on a flat ground surface. The second case compares data from loose-sand buried geophone with that from sensors coupled to the ground using concrete blocks.

Jan 1, 2014