Search Documents

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By Bryce T. Tripp

Utah's abundant industrial rock-and-mineral resources support a relatively small but important sector of the State's economy. In 1983, six of the top 10 nonfuel mineral commodities (by value) were industrial commodities. Portland cement was ranked fourth, potash fifth, halite sixth, phosphate seventh, construction sand and gravel eighth, and lime tenth. Portland cement was produced by three operators, principally from the Jurassic Twin Creek Limestone. Potash was produced by three companies from Pennsylvanian beds in the Paradox Basin, surface brine of the Great Salt Lake, and subsurface brines of the Great Salt Lake Desert. Halite was produced by eight operators, primarily from surface brine of the Great Salt Lake. Additional production came from salt beds in the Jurassic Arapien Shale, solution mining of the Pennsylvanian Paradox Formation of the Hermosa Group, and subsurface brines of the Paradox Basin. Phosphate was mined by one company from the Permian Meade Peak Phosphatic Shale Member of the Park City Formation. Construction sand and gravel were produced by dozens of operators, primarily from Quaternary Lake Bonneville beach and nearshore deposits. Lime was produced by four operators from Paleozoic formations in the Basin and Range physiographic province of Utah. The future production of these and other industrial commodities, though individually uncertain, is expected to increase gradually as a group. Factors favorable for the future of the industrial commodities industry in Utah include large to almost unlimited resources for the major commodities, a healthy projected population growth, an abundant local supply of relatively inexpensive energy from coal and natural gas, and a favorable corporate tax structure and business climate.

Jan 1, 1987

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

Among underground coal miners, roof bolter operators are generally considered to have some of the highest risks for hazardous respirable dust exposure. This is because bolting requires drilling into roof strata that can often be a source of silica and silicate dust, which are associated with occupational lung diseases. However, little is known about the variability of dust characteristics (e.g., mineralogy constituents, particle size) in the vicinity of the bolter—or when specific dust controls are applied. As part of a prior NIOSH study, respirable dust samples were collected during several different events in standardized locations around an active roof bolter, and personal samples were also collected from the operator during the cleanout of the bolter’s dust collection system when it was equipped with a novel wet dust box versus a traditional dry box. Those samples were made available for follow-up analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDX), as well as direct-on-filter Fourier transform infrared spectroscopy (FTIR). Results showed variability in dust constituents and particle sizes at locations around the roof bolter, and indicated some event-to-event differences in dust sources. Additionally, compared to the dry dust box, the wet dust box appeared to reduce (by 41–82%) the relative silica and silicate content in the respirable dust to which the operator was exposed during cleanout. Furthermore, an inter-laboratory comparison demonstrated the reproducibility of a standardized direct-on-filter FTIR method for estimating quartz mass (i.e., the predominant form of crystalline silica) in respirable coal mine dust samples. However, for constituent analysis by SEM–EDX, differences observed between results from two independent labs indicate that standardization of the analytical protocol is necessary to enable comparability of results.

Jan 5, 2024

By R. E. Wade

The Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. & P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 1, 1914

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By Willard L. Hunter

The smelting of tin slags was undertaken at the Bureau of Mines Albany Metallurgy Research Center (AMRC) to produce crude columbium-tantalum ferro-alloy as a unit operation in the production of pure columbium and tantalum oxides or chlorides. Columbium and tantalum-rich alloy was prepared during short unrelated campaigns over a total period of 12 years. Tin slags from Malaya and the Congo (Geomines) were smelted. These slags were reduced by carbon in a small, single-phase, steel-making furnace} a larger three-phase, steelmaking furnace, and a three-phase, submerged-arc furnace, In all cases depleted slags were fluid and easily tapped from the furnace. However, unless diluted by iron additions, the metal product was a viscous, high-melting, heterogeneous mixture that could be removed from the furnace only by hand rabbling.

Jan 1, 1966

By Ivan C. Machado

Jaguar Mining Inc. is implementing a 1.1 Mtpy, 7-year LOM gold project in the Iron Quadrangle (?Quadrilátero Ferrífero?), Brazil. Construction is on schedule and startup is programmed for Q2 2010. Mill feed grade averages 4.43 g/t and LOM gold production is estimated at 800,000 oz. The project entails two sulfide underground mines and three oxide/transition open pit mines. A state-of-the-art flotation/gravity concentration/CIP Plant has been designed based on testwork carried out by internationally recognized Canadian, U.S., and Brazilian laboratories. The mass recovery of the flotation section is only ca 10%, while its gold recovery is about 90%. Therefore, the CIP-ADR Plant will treat only 10% of the solids mass contained in the mill feed, while 90% will be fully cyanide-free material that will be partially used to feed a Backfill Plant. The leached tailings will be conveyed to a rather small tailings dam, whose 20- m3/h supernatant solution will be treated by a new electrolytic technology. The plant design contemplates a High Density Thickener for the cyanide-free rejects exceeding the backfill demand and a Regrinding Section before the Leaching Circuit. The estimated overall metallurgical recovery sits around 92%. This paper focus on the use of modern technologies to reduce costs, risks, and liabilities.

May 1, 2010

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By Leo Dana

As a part of an investigation conducted by the Cement Section of the Bureau of Standards, at the plant of the Security Cement & Lime Co., Security, Md., the High-temperature Measurements Section was called upon to measure temperatures in a dry-process, coal-burning kiln. Although the measurements were made only under the conditions existing in one plant, the methods employed and the conclusions drawn apply, in a general way, to those existing in most plants. As far as we have been able to learn, no sufficiently thorough methods of making accurate pyrometric measurements in the sintering zone and in the rear end of rotary cement kilns have been described. It is believed that in this investigation, data were obtained that can serve as a foundation for further study of the problems of pyrometry in cement kilns. IMPORTANCE OF TEMPERATURE MEASUREMENTS IN ROTARY CEMENT KILNS The manufacture of Portland cement is today fairly well standardized. The various steps in the manufacture have been developed to such an extent that the process is almost automatic. In spite of these strides the efficiency of utilization of heat in the kiln is very low and an undue proportion is wasted; for example, about 50 per cent; ordinarily goes up the stack. In order to prevent these losses, not only should means be provided to utilize the waste heat but instruments, such as pyrometers, should be installed to study and control the operation with the view of minimizing the losses. At the same time, such control will produce a more uniform product. The saving in-fuel that may be effected by the proper use of pyrometers would be much more than their cost. Where these pyrometers should be installed and what they can show are very briefly indicated in the following paragraphs and discussed in greater detail later.

Jan 9, 1919

By Kirk P. Kinart

The mid to late 1980s saw a modern day global gold rush that largely focused on the mature mining countries of the United States, Canada and Australia. This gold rush led to a large number of new discoveries in these countries and phenomenal growth rates in annual gold production. For a variety of reasons, however, gold exploration and development activity appears to have peaked in these countries. The drive for mineral investment is, instead, growing in lesser explored countries (LEC). LECs, particularly those of Latin America, are currently enjoying greatly increased attention from North American mining companies. They are becoming major consumers of mineral investment capital and are important markets for exploration and mining skills. Through sole ownership, joint ventures and subsidiary companies, Battle Mountain Gold now operates or controls gold mines in the United States, Chile, Bolivia and Australia. And it has been or is an active participant in gold exploration or development projects in seven other countries, six of which classify as LECs. In selecting new country entries and opportunities for mineral investment, there are several factors to be considered and parties to be satisfied - shareholders, corporate management, financial institutions and host country governments. This article, though, focuses on some of the more practical concerns of the exploration unit as a whole and the exploration geologist in particular. The exploration unit's "new country" concerns primarily relate to exploration potential, ownership security, quality and availability of data and the ability to operate efficiently. The following material reviews each of these concerns and how they impact the new country entry decision, exploration strategy, chances of success and human experience.

Jan 1, 1993

By Elear Gómez

La pirometalurgia de los concentrados de plomo se inicia en el siglo XIX y desarrollada con mayor intensidad en el complejo metalúrgico de La Oroya que inició sus operaciones en el año de 1922, con el proceso pirometalúrgico de los concentrados de cobre, en el año de 1928 se inicia el proceso pirometalúrgico de los concentrados de plomo. Los procesos se desarrollan a una altitud de 3,720 m s. n. m. Nuestros conocimientos del tratamiento pirometalúrgico de los concentrados de plomo, nos permite estar en la capacidad de poder refinar todos los concentrados de plomo que se producen en nuestra patria. Esto permitirá generar fuente de trabajo que es lo que necesita nuestro país, en la primera etapa seria producir los metales y en una segunda etapa industrializar el país.

Sep 29, 2023

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By T. T. Chen

The behavior of gold in a conventional copper electrorefinery anode slimes treatment process is expounded on in this study. In the raw anode slimes generated in a copper electrorefinery, gold occurs mainly as tiny particles of metallic gold, which are commonly attached to selenide particles. Some gold is also present in selenide form. Decopperizing the anode slimes retains much of the metallic gold, but also promotes the incorporation of gold in the structure of silver-rich selenide species. A greater fraction of the gold is converted to (Ag,Au)2Se or Ag3AuSe2 when high-Se and high-Ag anode slimes are decopperized at elevated temperatures and pressures. After pelletization and roasting of the slimes, the gold is converted to a (Ag,Au)-alloy and Ag3AuSe2. Smelting of the roaster products eliminates the selenium and converts the gold to a silver-rich (Ag,Au,Pd)-alloy in the dore metal. In the subsequent silver electrorefining process, gold collects as a gold-rich (Au,Ag,Pd)-alloy in the gold mud. Dore smelting rejects many impurities as a silica slag; minor amounts of gold are present as a (Ag,Au,Pd)-alloy in the silica slag. This gold is recovered by flotation and is recycled to the dore furnace. Gold is identified in both the tellurium caustic leach residue and the parting plant wash water mud as tiny particles of metallic gold. These products are also recycled to the dore furnace to recover their gold values.

Jan 1, 2008

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994