Search Documents

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

[This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative Agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of tines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935.-36.3/ The present report cover brands of gasoline represented by 1,490 samples plus thus: from the Pacific Coat, which ;sere averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, Whereas in other areas only one Company reported on a brand. Thus, it can be seen that soma of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Severe changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas any western Tennessee. The Rocky Mountain area, have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and. Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico , and El Paso, Tex., have been combined to represent the South Rock Mountain district. The Cleveland district has been expanded to include Ohio ant. Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippee, and northern Florida.]

Jan 1, 1938

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

I HAVE previously demonstrated to you as well as I knew how in what way ores are treated and then how the separated metals are brought to their pure and ultimate limit of perfection by means of smelting and other artificial fires; all except gold, which remained incorporated in the silver. Because the method used for the others does not serve for this, and if indeed it did serve it would be a great labor and could not be done without a great loss of the thing, it is therefore necessary to proceed with the practice of another art if you wish finally to extract gold from the bonds of the intrinsic substance of silver, for it exists bound and scattered in this like the soul in the body of living creatures. In this, unlike the other works where you make direct use of the vigor of the fire, you use a substance that is like water, drawn by the force of fire from a very powerful composition of two materials. This is a very marvelous thing to consider as a liquor because of its powerful effects. It is made by artificial distillations and it has an acid property and the power of corroding and reducing into itself silver and any other metal placed in it, with the exception of gold. Nothing is apparent in it except a pure water. It is indeed a very ingenious thing for which we must be greatly indebted to that philosopher, alchemist, or whoever else was its discoverer. The silver that contains gold is put in this water, and from its former quiet state you will see it change as if forced to combat and breathlessly devour and consume that silver in itself and change it into water. This happens in a very short time and with very little help from the heat of the fire. All the gold that was united in the silver you will see like sand at the bottom, and when the water is taken off by decantation it will freely give you all the gold without any loss. Nor is it so ill-mannered as to fail to restore the silver to its place if you wish; and though it seems to have consumed and spoiled it as it was before, it returns it to you without loss. Since the process of this art is a very useful thing for anyone who knows

Jan 1, 1942

By G. Rajesh

Mathematical modeling of bioremediation has gained importance as it is used as an optimization tool for the remediation process involved in contaminated sites. The bioremediation of Cr(VI) has been studied taking into consideration the initial Cr(VI) concentration Cr(VI)ini, bacterial growth substrate concentration (S), maximum growth rate (µmax), yield coefficient (Y), half saturation constant (Ks), and inhibition constant (KI). As the enzymatic reaction is also affected by initial substrate concentration (Sini) and Ks, different ratios of (Ks/Sini) are analyzed. As the inhibition constant (KI) is not constant for all the enzyme reactions and it varies with Cr(VI)ini, the correlation between (KI) and Cr(VI)ini is developed. A set of differential equations pertaining to bioremediation of Cr(VI) has been solved using FORTRAN 90 program adopting the model developed. The results are verified with the experimental data from the literature and a good correlation has been obtained between the experimental data and the model predictions. Keywords: bioremediation, hexavalent chromium, mathematical model, inhibition kinetics

Sep 1, 2012

"Injection technology has been an important subject from the early days of ladle metallurgy until the present. During the last decade, there have not been many publications in the area of injection technology. It is the author's opinion that with the challenge to find new solutions especially to environmental and energy related problems as well as better understanding of phenomenas from computer modelling, a new era of inventive injection technology developments is at hand. This is illustrated in the article with examples from six different areas where MEFOS is or have recently carried out R&D work related to issues from the injection technology field. IntroductionThe boom in injection technologies came with the introduction of ladle metallurgy treatment during the '70s and '80s. Since then, the theories and principles have been thoroughly laid down by a number of scientists and also published at several early SCANINJECT conferences.Not many new technologies/applications have been presented during the last ten years. This might lead one to believe that everything is known and done. Those, like MEFOS, who are challenged to find technological solutions to a number of environmental problems and energy saving issues in the pyrometallurgical field are, however, continuously faced with the task of developing new injection technologies.Especially, the call for sustainable technologies to solve environmental problems is a challenge for metallurgists all over the world and it will surely induce a revival of injection technologies. So, in order to encourage all injection experts, let us share some new experiences and let us encourage each other's creativity to solve some of the demands of the future society.The following show some examples of technologies under development, or recently tested."

Jan 1, 1996

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree Electrowinning is an attractive method to recover gold from the relatively concentrated aurodicyanide solutions produced by the elution of loaded carbon, provided that the plated gold can be easily removed using high pressure water sprays. In practice, difficulty with the removal of the gold is occasionally experienced and has been correlated with the presence of high concentrations of copper in the eluate. In this work, the influence of copper on the electro-plating of gold was further investigated using a laboratory electrowinning cell with a rotating disc cathode, polarization, and adhesion tests. It was found that the reduction of copper will compete with gold electrowinning at high copper tenors and that the adhesion of the precipitated gold is also increased under these conditions. Keywords: reduction, adhesion, morphology, current efficiency, limiting current.

Jan 1, 2004

By Dave Willis

In ME'S 1994 Powder River Basin (PRB) coal transportation article, the lead author described some destinations pursued by the railroads. As with many destinations, though, they turned out to be merely stops on the way to places that have yet to be reached. Along the way, the railroads discovered that making it better is a continuous process, not just something done in several phases. This was always known but not at the awareness level that exists in 1998 railroad environments. This update of the 1994 article includes railroad companies' plans for the future of rail transportation in the PRB.

Jan 1, 1998

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

By Douglas H. Brown

Cadmium and other 'minor' metals in Canada tend to remain inconspicuous given the prominence of the country's massive production of other minerals. This same reality is reflected in the accuracy and deficiency of quantitative data concerning the sources of supply and demand for these metals. It is the intent of this paper to identify the nature of some of these difficulties and to reconstruct a more accurate description of Canada's production and consumption of cadmium, based on the results of recent surveys undertaken by the Mineral Policy Sector of Energy, Mines and Resources Canada and Noranda Sales Corporation Ltd.

Jan 1, 1978

By R. Darlington, S. Ji

"High pressure die casting is a promising process to make thin-wall components with high dimensional accuracy and excellent surface quality. However, the non-uniformity is one of the important features in castings. The inhomogeneity in tensile properties and microstructural characteristics were studied for the castings with different thicknesses made by high pressure die-cast Al-Mg-Si alloys. For the local mechanical properties in the die-castings, the casting skin provided the highest, whereas the casting centre provided the lowest yield strength, UTS and elongation. The yield strength, UTS and elongation were significantly decreased towards the casting centre. The microstructural inhomogeneity is characterised by the segregation of coarse fragmented dendrites, the reduction of solute concentrations of Mg and Si, and the increase of porosity level from the surface to the centre of castings. The growth velocities of eutectic a-Al phase estimated using the Jackson-Hunt model confirm that the growth variation is larger in the thin castings than that in thick castings.INTRODUCTION Inhomogeneity is an inherent characteristic in as-cast microstructures of a variety of alloys because of their non-uniform chemistry, microstructure, defects, topology and the resultant mechanical properties in the different ranges of localization (Campbell, 2003). Generally, three types of inhomogeneities characterise casting microstructures, which include (a) the casting defects of shrinkage and gas porosity, misruns, cold shuts, inclusions, hot tears and hot spots; (b) the non-uniform microstructure from the surface to the centre of castings; and (c) the non-uniform microstructure from the dendrites grown from primary solidification and the structure formed during the subsequent eutectic solidification in inter-dendritic regions. The chemical composition and the morphology between the primary dendrites and the inter-dendritic eutectics also differ in the as-cast microstructure. Obviously, the inhomogeneity is different in the castings obtained from different casting processes."

Jan 1, 2018

By Jr. Baldwin. William M

WELL known to every metallurgist is the fact that different production schedules will profoundly affect the character of annealed metal strip. Yet the number of conditions [ ] that may be wrought by different combinations of rolling and annealing schedules is so myriad that despite the continual research that is being applied to this subject, the complete picture is not yet known. Copper, like all other metals, during the process of rolling or annealing, develops certain crystallographic configurations which should not be dismissed as being too impractical, for the crystallographic condition existing within the metal is a principal influence upon both the external mechanical properties and the behavior of the material [ ] when it is subjected to such operations as bending, flanging, drawing, and so forth. EFFECT OF ROLLING AND ANNEALING UPON THE CRYSTALLOGRAPHY OF COPPER STRIP The most salient points in the crystallographic reactions of polycrystalline copper to rolling and annealing may be best represented graphically by a "map" such as that given in Fig. I. I. As copper strip is cold-rolled from a randomly oriented structure (pole figure I),

Jan 1, 1942

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006