Search Documents

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By J. R. McWilliams

THE task of recovering most of the contents of an oil and gas reservoir economically presents many and varied problems. In order to attempt intelligently a solution to these problems, an understanding of fundamental physical laws is essential. As the pertinent facts needed in applying these laws to recovery problems are not readily obtainable, observation must be made and the data tabulated. Here, good judgment must be exercised, for at best the information is meager. The engineer is well fitted to undertake the task of solving this problem. In my opinion, the decision on the part of some production executives to allow the engineer to cope with the oil recovery situation and other problems, is an outstanding example of improvement in production methods. The executive head must make this decision or the qualified engineer will be working under a severe handicap with the present system of supervising the production of oil and gas. A qualified engineer should have not only the required technical training but also enough field experience to enable him to understand the difficulties encountered in producing oil and gas. Such a man tactfully cooperating with the practical oil man can greatly improve present methods of oil recovery. The realization that nature's forces have not been efficiently controlled in past recovery of petroleum deposits has recently brought distinct improvement in production methods. Papers are to be presented at this meeting discussing in detail improved methods of conserving gas in both flowing and pumping wells, and also methods of lifting oil after Nature's supply of gas has proved inadequate. The application of back pressure to producing oil wells has not, to my knowledge, been extensively applied in Oklahoma or Kansas up to the present time. Most of the flowing wells are allowed to flow through the casing until the rock pressure has been dissipated. However, some flowing wells have been tubed before the well stopped flowing through the casing. Recording pressure-gages can be installed to study well performance.

Jan 11, 1926

By Kadri Dagdelen, Lee J. Zamalloa

Truck-shovel dispatch systems based on linear or nonlinear programming algorithms have been in operation since the mid-1980s, with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine. These systems are known for shortcomings related to the logic behind the decision-making of the operational objectives. This makes it necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. To address this issue, the present work discusses the implementation of a methodology based on artificial intelligence (AI) techniques to assist in the decision-making of the best optimization goals arrangement when operating a fleet management system. The focus of the analysis is on the evaluation of variable goal weights in a nonpreemptive, multigoal optimization model for multiple uncertain scenarios based on regions of optimal feasibility.

Apr 1, 2025

By Cameron Dunn, Callum Fryer, Carmen Hu, Craig Sewell, Peter Stakne, Andrew Raine

The Woodsmith Project is located in north-eastern England within the North York Moors National Park. The strata contains the world’s largest known high-grade Polyhalite resource of around 2.66 billion tonnes. The Project was initiated by York Potash Limited (YPL), a subsidiary of Sirius Minerals plc., but in March 2020, a takeover was completed by Anglo American, one of the largest mining companies in the world. Polyhalite is an evaporite mineral and contains essential nutrients required for plant growth. The Polyhalite will be extracted via two deep mine shafts and transported underground from the mine site to a Materials Handling Facility on a Mineral Transport System (MTS), which comprises a high-capacity conveyor belt system located within a 4.9 m ID tunnel. In 2018, STRABAG were awarded with the design and construction of the MTS tunnel and associated infrastructure, including the high-capacity conveyor system. The scope of work consists of 300 m of open cut, 100 m SCL tunnel, 36.5 km TBM drive (originally anticipated as three separate TBM drives) along with a network of underground caverns at the Woodsmith Mine. The construction of two 380 m deep intermediate access shafts was later awarded as Amendments to the Contract. The tunnel is constructed using a Herrenknecht Single Shield TBM. As a result of how the various elements of the project have developed over time, the first TBM drive has been extended to ~29 km making it the worlds longest single heading TBM Tunnel when complete. The option of completing the entire tunnel length with a single heading TBM drive is currently being assessed by Anglo American and STRABAG. This unprecedented tunnel length requires two intermediate shafts to provide essential access and services, the first intermediate shaft is at Lockwood beck (LWB) and the second is at Ladycross (LDX). The LWB shaft has been constructed utilising the innovative Blind Boring technique never used before in the UK. This paper will explain the methodology and technical risk management associated with this technique. The authors believe that the collaborative approach between all contract partners is and continues to be the important contributor for the success of this project.

Jun 13, 2023

By Rolf R. Schillinger

It is established to an increased extent that the basic questions about raw material extractions deal with water, dust, noise and vibrations. If it has not been definitely proven that these points won?t lead to excessive environmental strains, attempts at any explanations will meet with disapproval in advance. In order to answer the basic questions about dust, noise and vibrations quality management becomes most important, particularly with respect partly unavoidable emissions of production processes. The specific questions have to be answered within the context of good blasting practices, latest discoveries of the explosives industry, and by use of a Blasting Works Quality- Management, which includes both production quality and Risk-Management. The paper shows a practical way to work out a Quality-Management Program for companies involved in blasting activities.

Jan 1, 2002

By William Campbell

(Cleveland Meeting, October, 1912.) THE structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, it series of transition-products with distinctive structures, to which have ,been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school ; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-products-all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron-carbon diagram and the structures met with in hard- * Associate Professor of Metallurgy, Columbia University in the City of New York.

Dec 1, 1912

By Jun Xiao, Xiaodong Li, Chunming He, Daixiong Chen

"Benzohydroxamic acid with double dentate can react with copper to form cyclic hydroxyl oxime acid copper chelate, indicating a good selectivity for copper oxide minerals flotation, especially for malachite. The flotation results of the pure malachite mineral show a strong synergistic collecting effect between hydroximic acid and xanthate at a ratio of 3.5:1, achieving a malachite recovery of 95.5% when certain sodium sulphide is used as a sulphidizing agent in the optimal pH range. Thanks to the synergistic collecting effect, the flotation recovery of malachite of a real refractory ore flotation ,can reach over 92% under the optimum condition, a 12% higher than the recovery achieved with the conventional collectors. In industrial application, the flotation of the copper oxide minerals is improved , leading to a high efficiency utilization of copper oxide resources.INTRODUCTIONBeneficiation of copper oxide ore is one of the recognized challenges in mineral processing industry. Copper oxide ore is a vital component of copper resource in the world, which has abundant reserves. Majority of sulphide deposits has oxidized zone on the top, and some deposits are oxidized to become the large and medium-sized oxide deposits (Willam & Chavez, 2001). Most copper oxide ores have problems in processing such as high slime consumption, poor floatability, complex ore property and low flotation recovery, so it is of great significance in beneficiation of copper oxide ores to develop an efficient collector, especially for malachite (Fu & Gu, 1997; Wen, 2010; Riet, Kier & Elford, 1980). At present, sulphidization-xanthate flotation is the most important method for treating copper oxide ore. In recent years, due to the decreasing ore grade, the utilization of refractory copper oxide ore draws more and more attention (Zhou, 2003), except for sulphidization-xanthate method, chelating flotation method (Lu, 2009), chemical beneficiation method (Lenormed, Salman & Yoon, 1979), microwave radiation flotation method, hydrothermal sulphidization-flotation method (Mao, Wen & Fang, 2014) and ammonia leaching of sulphide precipitation-flotation method (Lekang, Stevik & Bomo, 2003) have occurred."

Jan 1, 2016

By D. C. Hilty

C. E. SIMS*—This is a most interesting and important paper. It is important from two standpoints. First, it has as-spects of being highly accurate and therefore extremely useful to the operating man in showing how far he can go in oxidizing carbon from a steel bath while retaining chromium and the effect of temperature on this limit. Fig 5 is undoubtedly the highlight of the paper, and in checking it against available data, it seems capable of predicting actual results. The other important aspect is the apparently significant fact that reactions within a steel bath, such as between carbon and an oxide, are homogeneous reactions which do not require equilibrium with an external phase. In this case, it seems obvious that the reaction and the equilibrium established were between dissolved carbon (or carbide) and dissolved CrO. The classic reaction which requires equilibrium with solid Cr2O3, did not fit the data. It was recognition of this principle that made Fig 5 possible. G. R. FITTERER*—It might be in assuming the CrO is dissolved in the metal that you are actually approaching the correct factor for activity. If that is true and if the percentages that were used represent an equilibrium constant, this would mean, in effect, that the minimum temperature at which chromium would be reduced by an equivalent percentage of carbon would be about 2400°F from your equation. I believe that is in line with my experience particularly if you deal only with low percentages. J. CHIPMAN†—The author in discussing the equilibrium of the reaction offers two choices of explanation. One postulates an effect of chromium on the activity coefficient of carbon; it would require perhaps more data than are available to us at the present time to test this thoroughly. The other postulate which he offers is a reaction with CrO. This explanation is consistent with physical and chemical principles provided that a solid phase CrO is present, and that is essentially what he is postulating. If that oxide were present one would expect and, I think, almost require the kind of results that he obtained. The weakness of that postulate lies in the lack of confirmatory evidence regarding the presence of solid CrO as such. This should offer an interesting subject for further study. It seems a pity that the theoretical arguments revolving around CrO should have obscured for a moment the very real excellence of this paper. E. CARTER*—I think there is a problem that presents itself in practical application where the metal temperature is from 3200 to 3300 and the temperature desired in pouring is considerably less. B. M. LARSEN†—I get the impression from some of the work that was done earlier that there is probably a localized zone of high temperature at the slag metal interface which effects the removal of the carbon. Without that I wonder if the effect is possible to have a localized superheat and an equilibrium there favorable to low carbon content and

Jan 1, 1950

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By John W. Sweeney

The southeastern phosphate industry is investigated to determine its role in supplying the United States and world phosphate demand. The report shows that the southeastern (Florida, Tennessee, and North Carolina) phosphate industry is the leading domestic and world producer of phosphate rock, The report emphasizes size and organization, production capacity, transportation, and marketing of the southeastern phosphate product, Factors affecting the supply- demand relationship of the southeastern phosphate industry and world phosphate production-consumption relationships are analyzed and related to the southeastern phosphate industry. Past trends are projected and the future role of the southeastern phosphate industry is analyzed to determine its ability to supply the United States and rest-of-the-world phosphate requirements in 1985 and 2000. The projections show that southeastern resources are ample to supply domestic and export requirements at the projected rates of consumption well beyond the year 2000.

Jan 1, 1970

By F. J. Sotillo

Mineral processing requires good classification of particles to attain an adequate separation of minerals. This is of utmost importance in the case of sulfide minerals. An ideal classification is obtained when particles are separated at a given mesh, which is fixed according to the characteristics of each sulfide ore. Under these ideal conditions, particles coarser than the mesh of separation are recovered in the underflow, whereas particles finer than the mesh of separation are recovered in the overflow. This paper presents the results of pilot plant tests that were performed on Ag-Pb-Zn and on Ag-Au Peruvian sulfide ores using a Density Separator, and the comparison of these results with those obtained using hydrocyclones, under similar operating conditions. The results show that the ratio of circulating load is reduced by 50% by using a Density Separator with respect to that obtained by using hydrocyclones. Moreover, the effect of the improvement in the separation efficiency obtained by using the Density Separator on the kinetics of flotation is also shown. Silver recovery of the Ag-Pb-Zn ore increased by 18% whereas gold grade in the concentrate of the Ag-Au ore is doubled.

Jan 1, 1998

By Robert J. Evans

The Bureau of Mines is sponsoring a variety of long-term, high-risk research to advance state-of-the-art technology in U.S. underground coal mining. This report reviews the status of many Bureau projects that support fundamental underground coal mining operations; the project areas include cutting coal from the solid (extraction), hauling coal from the face (transport), and activities that sustain daily operations (logistics). Innovative equipment and technology have been developed, with these major objectives: to significantly improve coal mine productivity, to further advance coal recovery and personal safety within the mining industry, and to reduce the time needed to develop longwall panels. The majority of the prototype equipment covered in this report either has undergone or will undergo comprehensive evaluation at Bureau surface test facilities so that performance and reliability can be improved before the equipment is tested and evaluated in a working section underground.

Jan 1, 1988

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By D. X. Chen

Comprehensive utilization of the copper associated with the complex lead and zinc sulphide ore is a recognized and difficult technical issue in ore dressing field. Qi Baoshan lead-zinc mine is a typical complex copper-lead-zinc polymetallic ore deposit and difficult to process. The application of the. traditional process is not able to make the substantive progress. According to its mineralogical characteristics, the association of copper minerals with lead minerals is very close, and their particle sizes are very fine, and the copper and lead minerals are partially oxidized. Based on the laboratory tests and comparison between different process flowsheets, preferential flotation of copper minerals, being suitable for this ore, was chosen to recover copper. The separation of copper from lead applies the following technology: regrinding middlings with cyclones to classify, which improves copper lead mineral liberation, and increases copper and lead recovery; using new high-efficient collector with good selectivity, which is able to float copper minerals; and non-toxic combined depressant which depresses lead minerals. The above technical innovation, optimizing the process flowsheet, overcoming the complex traditional process flow with high production cost, obtained good technical and economic indicator. The difficult technical problem of copper lead separation was solved smoothly. After successful performance of the bench-scale experiment, commercial-scale test was carried out. In industrial trial, a copper concentrate containing Cu18.60 %, Pb7.40 % and Zn2.50 % was obtained with copper recovery of 58.49%, lead concentrate quality improved largely. The process opened up an unique path for the comprehensive recovery of Cu from similar lead and zinc non-ferrous metals mineral to comprehensively recover copper.

Jan 1, 2014

By B J. van Loggerenberg

The capital cost of major items of mining equipment is very high. The operating cost of such equipment is also high. It is therefore important that such expensive equipment is used productively. To this end mine management uses production data systems and management accounting systems to monitor events and provide data for analysis to enable management to make operating and business optimisation decisions. This could be done better if there was an understanding of productivity in terms of its utilisation and efficiency components. What has been missing has been a methodology to properly account for the productivity of equipment in terms of its contribution in dollars to the costs and profit of the mine. An explanation of the Productivity Accounting methodology will be given. It will then be shown that productivity has two components, that of capacity utilisation and efficiency. These are defined and the dollar contribution of each to costs and profit shown. The efficiency component tracks the effect of proportional changes in input cost quantities used in the mining process as mining production changes. The capacity utilisation component tracks the effect of step changes in the input cost quantities used in the mining process as mining production changes.

Jan 1, 2003

By J. L. Ellenberger

The U.S. Bureau of Mines has cooperated with Cyprus Casa Grande Corporation Cyprus Casa Grande Mine, Cas a Grande, Arizona, since 1988 to assess the hydrology of an in situ leaching test facility. This work has resulted in an in situ design for leaching copper oxide ore that takes advantage of the increased mineral access associated with poor quality rock surrounding mine drifts. Blasting and bulkheads are used to produce readily-leachable rubble and contain and control solution movement, respectively. The design reduces the need for handling solution under high pressures in an injection/recovery system for in situ leaching of underground ore bodies. Early work at the site recognized a stress redistribution zone and increased transmissivity near drifts. Fracture data from a corehole oriented parallel to the dip of the ore body indicated an increase in fracture frequency around drifts a distance of 21 m (70 ft) away from the 5 m (16 ft) diameter drifts.

Jan 1, 1994

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By A. B. Hooker, J. W. Paul

"There was a time when any suggestion that the Davy flame (safety) lamp be discarded, would have evoked unlimited, criticism. However, that time is past.Investigations both here and abroad have shown conclusively that the Davy lamp does not have the necessary factor of safety against ignitions of mine gas, and England, the lost stronghold of the Davy lamp in Europe, has eliminated this lamp and substituted safer types.In the United States there are companies who still use the Davy lamp in spite of all that has been said and published as to the dangers connected with its use.Recently the purchasing agent of an anthracite coal company requested the Department of the Interior, Bureau of Mines, to pass upon the safety of some braise gauzes for use in a shielded Davy lamp. A shielded Davy lamp is an ordinary Davy safety lamp equipped with a circular brass shield that is attached to the lamp posts. This shield extends about one-half way around the gauze and one-half of the gauze height. The main purpose of the shield is to prevent the lamps being extinguished by a sudden increase in the velocity of the air current past the lamp.The brass gauzes submitted for this test represented two grades of brass - a yellow brass and a red brass. The analysis of these brasses was not determined. Two shielded Davy lamps that were submitted for the tests each had a steel gauze. These steel gauzes were also tested. Tests were made in horizontally moving mixtures of Pittsburgh natural gas and air at velocities of 400 to 1,000 feet per minute. The gas percentages used were 7%, 8.6%, and 11%. Tests were made with the lamp shield in two positions relative to the lamp and direction of flow of the gas-and-air mixture. In one position the shield was between the gauze and flow, as normally used. In the other position the shield was on the downstream side of the lamp. The tests were continued until one or more failures or gas explosions been obtained with each of the six gauzes. The results of these tests summarized as follows:"

Jun 1, 1923