Search Documents

By Carl E. Johnson

INTRODUCTION A method for predicting water-flood oil recovery was reported by H. Dykstra and R. L. Parsons' in 1950. It is now generally known as the Dykstra-Parsons method and is widely used by petroleum engineers. The method is semiempirical and consists of a correlation of four fundamental variables. These are: V, vertical permeability variation;' a, mobility ratio; Sw initial water saturation; and R, fractional recovery of oil in place at a given producing water-oil ratio. The correlation extends over a wide range in each of these variables, and may be applied to all formations with initial oil saturations of 45 per cent or greater. The method of calculation originally outlined by Dyhtra and Parsons closely follows their derivation. And this is a convenient way of illustrating the development of some rather complicated ideas. However, in actual use it is more cumbersome than necessary. The purpose of this note, therefore, is to provide a simplified method for making Dykstra-Parsons predictions. A SIMPLIFIED GRAPHICAL SOLUTION The correlation between V, a, Sw and R, corresponding to a given producing water-oil ratio, can be shown on a single graph. This is best done by plotting V against a to show lines of constant R(1 - S, . WOR-0.2). Figs. 1, 2, 3, and 4 show these plots

Jan 1, 1957

By S. A. Mahon

AN interesting feature among the mining structures, on the Mesabi. iron range is the iron ore stacker erected in 1934 at the Mesabi Chief washing plant at Keewatin, Minn. It is built of structural steel, and carries a system of belt conveyors which collects the washed product of the plant and places it on a stockpile for subsequent shipment. Although the only one of its kind in the Lake Superior iron district, installations of similar nature have been used elsewhere in the handling of coal and gravel and in earthwork construction. The reasons for stocking Lake Superior iron ores may be as various and diversified as the methods used in building the piles. At the under¬ground mines the existence of the huge piles in evidence at each active shaft is due, principally, to climatic conditions in this north country where the shipping period is much shorter than the operating season. Conversely, at the washing. plants it may be desirable to stockpile washed ores because the shipping season is commonly of longer duration than the period during which the plants may be operated. Washed ores, and mixtures of which washed ores are a component part, have found high favor with the oper

Jan 1, 1935

By Daniel L. Noble

Riparian communities are those related to, or near a natural watercourse (or sometimes of a lake, impoundment, or tidewater). Generally, riparian communities contrast sharply with the dominant vegetation type in an area, for example, the willow-birch-aspen- dominated watercourse in the Black Hills with its associated beaver- muskrat-trout habitat as compared to the dominant monotype ponderosa pine forest on either side of the drainage. Riparian ecosystems are valuable for the aesthetics, namely, varied landscape; photography and art; human awareness; diversity of plant and animal life, some of which may be unique to that habitat; cover, food, and water for associated wildlife and domestic animals; for recreation; for domestic water supply; and as natural outdoor laboratories. One major negative impact on riparian communities is hazardous chemicals from effluents from agricultural, industrial, and mining- metallurgical processes. One such chemical is cyanide, long used in the processing of gold and silver, and discharged previously directly into some of our natural ecosystems. With present environmental awareness, industry and government are attempting to minimize or eliminate this contamination. Homestake Mining Company began processing gold ore in the Lead- Deadwood area of South Dakota in 1878 and has remained in production at variable activity levels to the present time. The amount of cyanide (and heavy metals) entering the ecosystem during this time can only be crudely estimated, in part because of the variability in activity and the lack of understanding and concern about environmental pollution until the 1960's. Whitewood Creek, a tributary of the Belle Fourche River which flows into the Cheyenne River and

Jan 1, 1983

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983

By Allen D. Gorrison

EFFORT to develop fundamental quantitative information and improved technique in the production of petroleum has long been faced with difficulties of a particularly evasive nature, owing to a combination of circumstances. In the first place, petroleum comes from far below the ground, out of sight, so that information derived from indirect observations must be extrapolated to reservoir conditions. If one does not force the analogy too far, the petroleum engineer may be said to be somewhat in the position of the astronomer. The actual phenomena which he wishes to observe in detail appear at a place so deep in the earth?s crust that personal observations and direct experiments are impossible.

Jan 1, 1942

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By F. Lambert

"Amok Ltd./Cluff Mining operates a uranium mine at Cluff Lake in northern Saskatchewan. The project consists of one open pit and one underground mining operation along with a full-scale milling installation.The underground stoping operations are of the narrow vein type and are done between two levels 50 m apart. The mining method is undercut with concrete backfilling. Cuts are 3.5 m in height and can be as narrow as 1.4 m in width.Stoping operations are mechanized utilizing a CT-500E electric Microscoop marketed in Canada by Teledyne. The machine is only 85 cm in width and does all the mucking in stopes. Ore passes are provided in stope roughly every 40 m to 50 m.This paper describes the utilization of the CT-500E Microscoop in the company's underground operations and provides performance data related to the experience.IntroductionThe Amok Ltd ./Cluff Mining operation is located in the northwestern corner of Saskatchewan. The project started in 1980 with open pit mining and milling operations. In 1983, an underground mining operation began production . Today, the Amok Ltd./Cluff Mining installation produces 800 tonnes of uranium per year , which originates from both the open pit and the underground mine at about the same proportion."

Jan 1, 1990

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

By A. D. Wilkinson

A CROSS-SECTION of the converter aisle through one of the converters and reverberatories is shown in Fig. 5. The aisle is 280 ft. long by 60, ft. wide by 681 ft. to the roof trusse, which have a 63-ft. span and are us )ported by steel columns spaced at 2b-ft. centers. Two 80-ton electric trails, supplied by the Welman Smith .Owen Engineering Co., with 20-ton auxiliary lifts, serve this building. Matte shells and converter-slag shells are dumped into heavily con¬structed flat-bottom bins located on the south side of the converter aisle and 1.0 ft. above the floor. The material is broken by ball and by hand, shoveled off into ladles for unloading on to the reverberatory charge floor, and charged into the furnace as previously mentioned.

Jan 1, 1934

Graham Macfarlane, Louisville, Ky. (communication to the Secretary*):—In the paper by S. Whinery under the above caption mention is made of the occurrence of Clinton iron-ore in Kentucky and Tennessee. I believe that this is really a ferruginous limestone in what the Tennessee Geological Survey calls the Fernvale formation. In Davidson and Sumner counties, Tennessee, this occurs at about the horizon stated by Mr. Whinery. The maximum thickness of the deposit is from 10 to 12 ft., but it averages between 6 and 8 ft., lying practically horizontal. The Red River Furnace Co., under my direction, opened a mine in the Fernvale " red rock" near Goodlettsville, Tenn., several years ago. When it was first found we assumed it to be Clinton ore, but the absence of the characteristic Clinton fossiliferous structure and other evidence satisfied us that it is really limestone saturated with iron oxide. I think the very low ratio of SiO2 and Al2o3 to iron content as compared with the usual ratio in the Clinton ore is also evidence in favor of its being the Fernvale. The Tennessee Geological Survey states that at outcrops where this ore has been leached it carries about 44 per cent. of iron; under cover, from 20 to 25 per cent. of iron and from 3 to 6 per cent. of silica, the remainder being chiefly calcium carbonate. Its phosphorus content is irregular and generally rather high for a foundry-iron mixture. Since it is more than self-fluxing, we have at times operated with a mixture of brown hematite and red ore with no limestone.

Jan 1, 1913

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By S E. Thornett, P L. Kitto, R S. Longley

"The Mbalam Iron Ore Project covers mineralisation in two areas of metamorphosed hematitic banded iron formation (itabirite) in the north-west Congo Craton; namely at Mbarga in south-east Cameroon and at Nabeba in north-west Republic of Congo. The site locations are shown in Figures 1 and 2.The Mbalam Project history is an example of a compressed, yet highly successful, exploration timetable. Due to the thick inaccessible equatorial forest location, the first access was by helicopter in February 2007 at the Mbarga Deposit. Drilling commenced four months later in June 2007. A maiden JORC Code compliant æhigh-grade hematiteÆ inferred mineral resource (190 Mt at 60 per cent Fe) was defined in May 2008, followed by a maiden æitabirite hematiteÆ inferred resource in July 2008 (1.2 Bt at 37 per cent Fe). Subsequently, road access to Nabeba was established in January 2010, with a maiden high-grade hematite inferred mineral resource (200 Mt at 63 per cent Fe) identified only five months later in June 2010. A maiden itabirite hematite inferred resource at Nabeba was announced in June 2012 (1.4 Bt at 34 per cent Fe). The success of the exploration programs has been due to two main factors: Establishment of high-quality camps and facilities at Mbarga and later at Nabeba in Republic of Congo. Exploration support included satellite links for site servers and communications, field logging computers, data acquisition software, an on-site sample preparation laboratory, portable hand-held X-ray fluorescence (XRF) and company-owned drill rigs from 2009. An experienced and dynamic technical support group based in Perth to provide database facilities, data evaluation, internal auditing and software support, resulting in expedited resource estimation and economic evaluation with state-of-the-art mining software. In June 2012, Sundance Resources Ltd announced the current mineral resources for the project of 775.4 Mt at 57.2 per cent Fe of high-grade hematite and 4.047 Bt at 36.3 per cent Fe of itabirite hematite. In December 2012, high-grade hematite ore reserves of 436.3 Mt at 62.6 per cent Fe were announced. These world-class resources and reserves have been delineated and evaluated in a very rapid time frame. This would be considered extraordinary in any environment, let alone in the remote equatorial forest of central Africa.CITATION:Longley, R S, Kitto, P L and Thornett, S E, 2013. Exploration history of the Mbalam Iron Ore Project, in Proceedings Iron Ore 2013 , pp 107-116 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Vladimir Grujic, Milorad Grujic, Ivan Djurkovic, William Riggs

"In this paper, we have studied efficiency of different chemical structures of frothers on copper ore Majdanpek. The goal was to find out the best suitable chemical structure, which allows good bubble formation, size and interaction, forces on mineral surface. The particle size distribution was between 10 and 100 µm. Our research was oriented on three groups of frothers: alcohols, poly glycol ethers and poly glycols.We also used different collectors based on similar or less similar alcohol group in chemical structure as in frothers, expecting higher stability of air bubble in contact with copper minerals. Minimal potential energy was determinate in the hydrodynamic conditions for different particle sizes. It was founded that it is proportional to air bubble volume on 0.88° and contra proportional to the kinematics viscosity of pulp.Analyzing the results, we find out that poly glycols decreased surface tension the most. Also, it increased amount of coarser particles to the top of pulp. This group is less sensitive to pH value compared to the others too.From the class of frothers with higher efficiency in flotation process, we pointed OrePrep X-75 and X-133 as frothers with expressive frothing characteristic in the alkaline and low alkaline circuits. Special suitability of those frothers for floating copper minerals makes their hetero polar molecules with more than one hydrocarbon radicals connected to one polar group. However, those froters have no nether high or low solubility and are non-ionization. Those froters indicate some small collecting characteristics too. In dispersion systems, those two frothers make two types of bubbles: smaller di < 1.2 mm; V = 0.0008 cm3 and middle di < 16 mm; V = 2.2 cm3 (di – Bubble diameter, V – Bubble volume). Transportation speed of air bubbles it is possible to calculate based on equation: ?s = 27.5 * di 1.4 cm/s. Distribution of free surfaces for chalcopyrite is average 80% in the class –74µm +10µm and 20% in the class -10µm. If we get all class sizes, we find that recovery (R) depends from the time by equation:"

Jan 1, 2003

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By Theo B. Comstock

TO the large majority of visitors the unique features of the National Park are interesting chiefly on account of their novelty. Scientists of all schools may find here food for reflection, and much that is rare and marvelous; but the real, practical uses of the reservation, aside from its pleasure-giving adaptations, are not as yet fully appreciated. Since 1873, the writer has on frequent occasions expressed freely his own views upon the proper means of utilizing the Park for the best interests of science.* Some of the recommendations made have been adopted by the authorities. At the suggestion of friends I present here a brief statement of facts concerning matters which may be of advantage for visiting engineers to know, hoping that the very limited stay of the Institute may thereby be rendered a little more profitable, and that our common profession may possibly receive some benefit. First, then, it should be understood that, as in many other cases in. the West, the present routes to the Park from the south are not the most direct. The expedition of Captain (now Major) Jones in 1873 discovered a practicable route for a, wagon or railroad via the head of Wind River, through To-gwo-tee Pass and Two-Ocean Pass, by which the distance from Point of Rocks, Wyoming, on the Union Pacific R.R., to the Yellowstone Lake, is only 290 miles. Eventually, it is probable that a railway line from Cheyenne or some other point in Wyoming will be constructed, which, taking advantage of

Jan 1, 1888

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010