Search Documents

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

By Luiz Guilherme Isfer Maciel, Marilena Cardu, Fernando Golin, Jacopo Seccatore

"This study applies the concept of the difficulty of tunnelling by drilling an blasting (D&B) to selectedcases from the Brazilian tunnelling industry. The difficulty of tunnelling has been defined in previouswork as the difference of specific drilling (SD) from industrial average trend: easier when SD is lowerthan average, more difficult when SD is higher than average. Results show how tunnels in Brazil tend tobe unrealistically more difficult to excavate when compared to similar excavations in similar geologies elsewhere in the world. It is thoroughly discussed the reason for such anomaly (up to +90% SD compared to industrial average). One reason could be the lack of options amongst explosive products on the brazilian market. Only ANFO and explosive emulsions are available in Brazil. Lacking high VOD(Velocity of Detonation) products might result in reducing the maximum allowable burden amongstproduction holes, therefore increasing SD. Another reason could be found in the tunnel designers’tendency of choosing D&B as excavation method for weak rock masses that would benefit from mechanical excavation. The reason to this tendency can be partly found in the lack of availability of mechanical excavation machines in the brazilian market. Blasting in weak rock masses requires more careful smooth blasting, hence a closer spacing amongst contour holes to avoid costly overbreak: this increases SD. A third reason could be found in the lack of skill amongst the local workforce. When dealing with unskilled workers the blast designers naturally tend to avoid highly optimized blasts thatrequire very skilled workforce to be realized on field. The designer in this case tends to leave the blastdesign simpler but more robust, at the cost of higher specific drilling and specific charge. The conclusions suggest that this unrealistic difficulty when compared to world average could be a simptom of the so-called “Brazilian cost” within the tunnelling industry."

Jan 1, 2017

By Mohamed A. Eliwah

This paper deals with the determination of hydraulic conductivity of the coastal coralline limestone aquifer of Jeddah, Saudi Arabia. This coastal area has witnessed urban development and establishment of towers which requires deep foundations, excavation and dewatering of huge quantities of unconfined groundwater. It is occupied with successive layers of soft detrital and consolidated massive cavernous coralline limestone of the Quaternary age. These layers are encountered at a depth of 1.5m and extend for more than 100m. Hydraulic conductivity values were obtained by analyzing the pumping tests data under steady and transient state conditions. Hydraulic conductivity values help in selecting the proper and safe dewatering system, as well as determination of discharge rates and quantities of groundwater to be withdrawn. Test results obtained from two surveyed sites showed that the values of hydraulic conductivity are greatly variable. It ranges between 118.1 and 1559.6 m/day at the first site, whereas at the second one it ranges between 94.6 and 350 m/day. These high values are attributed to the cavernous nature of the water-bearing formation. Jeddah city could be divided into three different dewatering zones extending from north to south parallel to the coast line. Well point dewatering system could be applied in the first zone while ditches and sumps are the most suitable dewatering method in the second and third zones. Dewatering using deep wells in such highly permeable formation will require withdrawal of huge quantities of water which will be accompanied by washing out fine sediment filling the cavities in the surrounding areas. This will badly affect the nearby buildings through settlement, crakes and other structural damages. Therefore, construction of grouting plug/blanket with thickness of 3.0 m at a depth of 20.0 m is recommended. This depth will be enough to support the plug against the hydrostatic pressure. Moreover, it is highly recommended to transfer the site into closed box, by using diaphragm walls or secant bored piles.

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

By M. X. Huang, Y. Z. Li

The titanium diboride (TiB2)-reinforced steel composite, designed for automotive applications, exhibits a combination of high isotropic Young’s modulus and low density as compared to existing advanced high strength steels (AHSS). The steel-based composite is produced by in situ precipitation of TiB2 particles during eutectic solidification followed by hot rolling, and its microstructure displays a homogeneous distribution of both large primary TiB2 and small eutectic TiB2 particles in the ferrite matrix. Instead of interfacial debonding, particle cracking is the primary mode of damage, revealing very high interfacial strength. To investigate the intrinsic interfacial strength, a hybrid method combining both nanoindentation and finite element analysis (FEA) was used. A micron-sized sample containing a single crystal TiB2 attached to the ferrite matrix was fabricated by focused iron beam (FIB), and was compressed using nanoindentation with a flat indentation tip. By combining the compression and FEA results, the interfacial strength was therefore determined.

Mar 1, 2017

By P Bartsch

Uranium solvent extraction, USX has been applied commercially for recovery and concentration for over 50 years. Uranium in acidic liquor, which is prepared following ore leaching, solid/liquid separation and clarification, can be treated through a sequence of operations; extraction-scrubbing-stripping, to obtain purified liquor. USX has dominated the primary uranium industry as the preferred technological route to converter grade yellowcake. The practices of design and operation of USX facilities has found renewed interest as new mines are developed following decades of industry dormancy. This article seeks to outline principles of design and operation from the practitioner’s perspective. The discussion also reviews historical developments of USX applications and highlights recent innovations. This review is hoped to provide guidance for technical personnel who wish to learn more about good practices that leads to reliable USX performance.

Aug 8, 2011

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

Low-grade, porphyry copper type mineralization at the Moonmera prospect is related to the intrusion of a granodiorite porphyry mass into the Upper Permian "Gracemere granodiorite". Significant copper mineraliza- tion appears to be associated with the alteration assemblage quartz-sericite- kaolinite. The ore shell is surrounded by a zone where montmorillonite and kaolinite are in greater abundance and this assemblage is over- lapped, mainly at depth, by potassium feldspar alteration. Secondary biotite is abundant throughout the mineralized zone. Preliminary sulphur isotope results on the sulphide mineralization are compatible with a magmatic origin for the sulphur.

Jan 1, 1974

By P. R. Seidl, R. C. C. Ribeiro, J. C. G. Correia

"More than 95% of asphalt pavement materials consist of aggregates. The highway and construction industries consume a huge amount of aggregates annually causing considerable energy and environmental losses. The aggregates are usually produced from neighborhood aggregate quarries or form natural aggregate sources. The use of marble and granite wastes from quarries as aggregates might help meet the increasing demands and slow down any detrimental effects on the environment. Chemical and physical results showed that the use of marble and granite wastes from quarries in the asphalt production is quite fusible. Consequently, granite sawmills would perform a clean technology. This technology would also have an economical impact by not spending on basalt extraction.IntroductionThe granite fines generated from sawmills of ornamental rocks comes as a great problem and it lacks undeletable solutions. This problem involves the preservation of the environmental and constitutes one of the subjects more critical the point of view of social beneficiation of the population. The Cachoeiro de Itapemirim County, Espírito Santo State, Brazil is an example, of this problem. In this area, the granite and marble fines generation is around 15.000 ton/year.The problems generated by these residues affect with more emphasis the animals, such as the cattle, which inhaled the water content fines of granite and this residue accumulate in their lungs. Other great problem observed is the sanded of the river and the reduction of aquatic life.This problem is beginning to be set out due to performance of Center of Mineral Technology (CETEM), and of several other organisms of Rio de Janeiro State, aiding the sawmills owner’s. This help consists of teaching the best procedure of discard the residues and studies for its use, for instance the production of mortars, tiles, bricks and road pavements [1]."

Jan 1, 2008

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

By H. N. Eavenson

EaRly in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 19,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork of Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This area has been described in various geological reports. The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas, and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches of the bottom of the seam; it is one of the best coking and gas coals in the United States. The average analysis of this coal is given in Table 1.

Jan 1, 1922

By J. L. Holman

In conjunction with its research program on separation, recovery, and recycling of metal, mineral, and energy-based materials in urban refuse, the U.S. Bureau of Mines is developing means to reuse and recycle plastics discarded in raw municipal waste. Experimental work on plastic waste from a community collection has produced some guidelines for systematic methods of processing, including air classification, cleaning, separation, and use or disposal. Sink-float methods are a practical means of separation into types. Methods for final disposition of the plastic waste include refabrication, thermal decomposition, and incineration.

Jan 1, 1972

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By Cledwyn Mangunda

Mining operations generate Acid Mine Drainage (AMD) that poses a significant threat to the natural environment. AMD treatment using Ca(OH)2 leads to the precipitation of a sludge dominated by a mixture of ferri-oxyhydroxides. This sludge has poor dewatering tendencies and is deposited in landfills with potential for metal remobilization. This study investigated the dewatering behaviour of a precipitate formed during elevated temperature treatment of a primary, pre-settled sludge from the neutralisation of aqueous acidic Fe2(SO4)3 and Ca(OH)2 solutions in an MSMPR reactor. The resulting treated precipitates were analysed for micro-properties, with results showing that an increase in the secondary reactor temperature from 25 °C up to 50 °C led to an increase in mean particle size, a decrease in the number of particles and improved dewatering behaviour at a ferric concentration of 300 mg/L. This was ascribed to the attainment of a circum-neutral surface charge that favoured agglomeration and a change in micro and nano-structure that allowed for better water passage.

By O. E. Kiessling

THE Committee-on Production Control, at its meeting held during the last annual session in February, 1930, evidenced great interest in problems of stabilization affecting all mineral industries. . No immediate program of activity for the Committee as a- unit was decided on, however,, and efforts during the past pear have consisted lirgely of further stressing the economic aspects of mineral production and of the action by committee members, :.serving in their individual capacities, in sponsoring constructive changes, in specific, industries. Of greatest interest to the general subject of production control in 1930 was the very definite advance toward better coordination of demand and supply in the petroleum industry. Furthermore, since opinion both within and without the oil industry now favors a constructive program, and with a gradual change in legal precedents, it seems not unreasonable to expect greater progress in the near future.

Jan 1, 1931

By I. Ngoma, Marijke Fagan, Susan Harrison, Rebecca Chiume

"Heap bioleaching is an unsaturated hydrometallurgical extraction process which is commonly applied to the recovery of copper from low grade sulfide ores as well as for preparatory treatment of gold ores. The leaching reactions occur in the liquid phase, catalysed by iron and/or sulfur oxidising micro-organisms. Contact of the mineral grains with the leaching solution is consequently essential for metal recovery. Additionally, the liquid is responsible for the transport of the liberated metal out of the heap under gravitation-driven flow. However, the highly inhomogeneous structure of the heaps coupled with low irrigation rates cause the flow to vary between being gravitationally and capillary dominated, resulting in non-uniform wetting of the ore. In this study a 132 kg agglomerated ore ‘slice’ is used to examine the effect of liquid distribution on microbial colonisation and mineral recovery in a long term bioleach (> 500 days) when irrigation from a single drip emitter source is employed. The novel setup enabled sample collection from ports positioned along the length and height of the ore bed, so that 2D maps of the degree of wetting and microbial colonisation could be generated at different times in the leach. Lateral movement of the liquid increased with bed depth; the majority of flow was below the irrigation point while the top corner of the bed that was not irrigated remained the driest region of the heap throughout the experiment duration. The lowest cell numbers were also recorded in the driest regions. Specifically, cell numbers in the top corner of the bed, 400mm from the irrigation point, remained at undetectable levels until the 283rd day measurement, in line with typical heap operation durations. This indicates that slow colonisation of the heap in the regions between irrigation points may be a significant issue in heap optimisation."

Jan 1, 2014

By V. Srajer

The Calgary Coal Research Laboratory of CANMET and the National Research Council in Ottawa are developing a series of computer models aimed at improving productivity and operational practices of the Canadian surface coal mining industry. One of the top priorities in this respect is a comprehensive computer model of truck/shovel system. A total of twelve mining companies supplied data for validation purposes. The supplied data, operating practices and variances of individual mining systems from the general version of the computer models are discussed in the paper. A short overview of the truck/ shovel model and a plan for future activities involving the application of the computer models for simulation of mining practices are also described. The presented paper summarizes the experience gained during the collection of data for the development and validation of the model.

Jan 1, 1986

By H. W. J. P. Neomagus, J. R. Bunt, D. L. Botha, N. T. Leokaoke

Coal briquetting traditionally makes use of high-dosage, nonpolymeric binders (such as coal tar pitch or molasses) or polyvinyl alcohol (PVA) at low dosages for the binding of fine and ultrafine coal. Due to constraints associated with the manufacturing and cost of PVA-bound briquettes, a novel polyacrylic binder was developed that could possibly be added in low dosages at room temperature. A set of formulations of two polyacrylic components (components A and B) was developed, from which an optimal binder mixture was determined. This formulation comprises 40wt.% component A and 10wt.% component B with a 0.04wt.% cross-linking additive, and the balance water. The uniaxial briquette compressive strength was used to obtain the optimal binder mixture. The binder mixture was added to the coal powder in dosages from 0.1 to 1.2wt.%. Mechanical tests and thermogravimetric analysis in an oxidized environment at a maximum temperature of 930°C were conducted. Binder-bound briquettes were compared to binderless briquettes and PVA-bound briquettes. Briquettes made from the polyacrylic formulation had uniaxial compressive strengths double that of the binderless briquette yield strength, as well as the minimum recommended compressive strength of 0.375 MPa. The organic binders did not affect the combustion of the briquettes, since the results compared well with the binderless briquettes. The polyacrylic formulation is considered to be a possible substitute for PVA in terms of mechanical and thermal properties and raw material cost.

Mar 1, 2021

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979