Search Documents

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By A. L. Mular

Optimization has been defined as the procedure of locating the best of something or the best way of doing something (Mular, 1971). Several texts (Himmelblau, 1972; Ray and Szekeley, 1973; Box and Draper, 1969; and Lee, Adams, and Gaines, 1968) on the subject are available. Such techniques have been placed in two categories, namely, off-line optimization and on-line optimization. For the former, an optimization model is employed; for the latter, a black box approach is involved. The essence of an optimization problem becomes obvious, when a response surface is considered. Suppose that a response (in this case, a criterion of improvement such as profit per day; grade of concentrate per day) denoted by Y, depends only on two variables, X1 and X2, which can be manipulated and controlled. The relationship between Y, X1 and X2 may be represented graphically as shown in Fig. 1. The diagram is called a response surface and its height, Y, is determined by X1 and X2. Points associated with equal responses constitute response contours. The shape is that of a hill, and optimization is the procedure of ascending the hill to reach the top (maximum). In practice, a response surface is subject to disturbances which distort its shape and shift its location from time to time, so that the exact location of a maximum is imprecise. Generally, constraints (restrictions of some sort) on responses and manipulable variables serve to define a region of permissible operation.

Jan 1, 1979

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By Laing W. P, Neill D. M, O&apos

The Reward polymetallic massive sulphide deposit occurs 35 km south of Charters Towers, adjacent to the Highway gold deposit (Fig. 1). It is hosted within rhyolitic lavas and interlayered volcaniclastics of the Cambro-Ordovician Mt Windsor Volcanics. Reward is a "blind" deposit discovered in 1987 after a long history of exploration by various companies in the area. The main pyrite dominant massive sulphide body occurs under 100m combined thickness of Tertiary fluviatile sediments overlying deeply weathered gossanous volcanics. The exploration case-history provides a striking example of how geological and structural models can be built up almost exclusively from drill information. Four different styles and ages of mineralisation are present: 1) volcanogenic Cu+Pb+Zn+Ag+Au massive sulphides of probable syngenetic origin; 2) remobilised Cu+Au in massive pyrite of metamorphic/deformational origin; 3) supergene and 4) oxide Cu+Au mineralisation of weathering origin. The massive pyrite body, containing chalcopyrite lenses, transects the stratigraphy and is inferred to contain in excess of 5 million tonnes. Overlying the primary mineralisation a supergene chalcocite rich zone contains a measured/indicated resource of 634,231 tonnes of 6.77% Cu which includes 287,000 tonnes of 1.32 g/t Au and 18 g/t Ag. In addition a measured/inferred oxide resource of 309,000 tonnes of 5 g/t Au and 27 g/t Ag overlies the supergene zone.

Jan 1, 1989

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By D. Saramak, T. Gawenda, A. Stempkowska, Z. Naziemiec

The aim of the paper is to discuss the possibility of producing aggregates with an increased content of regular particles, as well as to present a method of aggregate production which has not previously been used in the industry. Traditional aggregate production circuits require the application of three or four grinding stages (depending on the particle size of the feed), but for fine particle fractions of aggregates, irregular grains occur on average with a content of 10%. The innovative technological circuit can produce the aggregates with the content below 3%, even in a single- or two-stage crushing circuit. Downstream jig beneficiation of such prepared material results in higher separation sharpness, lower probable error index (Ep) and imperfection (I). Keywords: Aggregate production, jig beneficiation, mineral processing, raw materials

Jan 1, 2020

By Tilden Cummings

The extractive mineral industries share a number of common characteristics and basic problems which are completely different from those associated with manufacturing and mercantile operations. These industries now supply about 95% of the inanimate energy consumed in this country, and share with agriculture in providing virtually all of our basic raw materials. Mineral producers, like farmers, are subject to the economic hazards of fluctuating markets and prices. Unlike farmers, however, they cannot renew the productivity of the earth, but must seek continually for new sources of supply. The necessity for exploration and development of new reserves, to replace those used up by production, introduces additional factors of economic risk. These operations require the expenditure of large amounts of capital, often well in advance of any assurance of profitability. Commercial banks that understand these special problems can provide a variety of constructive financial services to the mineral industries. The history of cooperation between banks and mining enterprises has yet to be written, but there is every indication that it would encompass a period of hundreds of years. Records refer to depository and lending services by the early European private bankers involving precious metals and jewels. Many of the exploratory voyages to the Far East and the New World were organized with the financial backing of wealthy syndicates, some of which also provided banking services, in the hope of finding new sources of gold and other precious minerals. In the United States many large banks are closely identified with the development of some of the larger mineral deposits such as the Mesabi Range and the gold fields of California.

Jan 5, 1965

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

Acclaimed as one of the most remarkable orebodies anywhere on account of its length and richness, the Oroya Shoot occurs on the eastern side of the Kalgoorlie gold mining district close to the contact of a fine-grained with a coarse-grained greenstone, and in association with sediments. In the same stratigraphic position on the synclinal flanks of a large drag fold there are a number of other flat ore pipes, smaller, but almost as rich in tenor. Although differing in control structure they are believed to be related genetically as all show a characteristic development of a bright-green ore known locally as "green leader". Folding and bedding structures have played an important part in formation of the ore shoots.INTRODUCTIONThe Oroya Shoot is the biggest individual bonanza of Kalgoorlie's Golden Mile. It has been stoped almost continuously over a length of 4,300 ft., and about 2,000,000 oz. of gold have been won from it. Naturally pillars are not left in the best sections of such an orebody and the detailed geology of stoped out portions can only be inferred from examination of adjacent workings.No mention is made in the literature of the actual makeup of the orebody although a few structures are shown on some of the old cross sections. A diagrammatic cross section, Fig. 1, adapted from Stillwell (1929) illustrates the form of the Oroya Shoot.Gustafson (1937) drew attention to the role of folding, previously unrecognized, in Kalgoorlie geology, and indicated that the Oroya Shoot is associated with a minor drag fold on the east limb of the Brownhill Syncline, itself part of a larger left hand drag on the Central Anticline. The latter in turn appears to be part of a regional right hand fold system as shown by Campbell (1953).

Jan 1, 1959

By F. W. Jessen, James N. Howell

The accumulation of paraffin deposits in tubular goods has been recognized as a major production problem since the inception of the petroleum industry. This problem is not limited to any particular geographical area nor is it limited to a specific type of crude oil.' Generally speaking, "paraffin" deposition pertains to the deposition of any predominately organic material in flow lines, and possibly even at the sand face, which would hamper the production of oil. In some fields, a continuous effort is required to remove deposits of paraffin and in order to accomplish this, many unique methods have been devised. The best solution to this problem, however, is to prevent the formation of such deposits. One method which has been tried in a number of fields is the use of plastic pipe. The purpose of this investigation is to compare the relative effectiveness of several plastic materials to aid in the reduction or prevention of paraffin accumulations in surface flow lines. COMPOSITlON OF PARAFFIN DEPOSITS By definition, paraffin deposits are those materials which are insoluble in crude oil at the prevailing producing conditions of temperature and pressure. Such deposits1 s usually consist of small particles of petroleum wax intermixed with resins, asphaltic material, and crude oil. They may also contain a variety of foreign materials such as sand, silt, water, various metal oxides, sulfates and carbonates of iron. barium, and calcium. The petroleum waxes deposited in flow strings usually consist of both a "hard" and a "soft" wax fraction. These waxes are largely aliphatic hydrocarbons with smaller amounts of aromatic and naphthenic compounds. Nathan' has classified the hard and soft wax fractions. The aliphatic hydrocarbons present are those of high molecular weight with high melting points. Reistle3 pointed out that these high molecular weight compounds first separate from the oil due to a sharp decrease in solubility as the melting point increases. The identification of the resins and asphaltic materials rests, at present, on an arbitrary solubility procedure. Under certain conditions, materials which are insoluble in pentane (ASTM D-893) are defined as resins and asphalts. Subgrouping of these materials is made on decreasing solubility in benzene and carbon disul-fide. Shock' found some correlation be-tween the solvent response and the pentane insoluble content of paraftins: higher pentane insoluble fractions are less soluble in any of the commonly used commercial solvents. PARAFFIN CONTROL METHODS The methods used in oil fields to prevent and remove paraffin accumulations can be grouped into four general classes: (1) operative methods, (2) physical methods, (3) chemical methods, and (4) combination of any of these. Operative methods attempt to prevent the formation of paraffin deposits while the other methods are concerned primarily with the removal of these deposits. Plastic coated pipe has been used for a number of years to prevent cor- rosion in wells, and in manv instances paraffin deposits have -been greatly reduced. Field observations have indicated that plastic coated pipe not only reduced paraffin accumulation but in some cases eliminated deposition completely; however, data are needed to demonstrate the relative effectiveness of plastic materials. Deposition Apparatus The pipe used to determine the effect of velocity on rates of deposition was %- and 2-in. nominal diameter, and 5 ft in length. Steel, butyrate, rigid PVC, kralastic resin-type plastic pipes, epoxy coated pipe, PVC lined glass fiber pipe, and aluminum pipe were tested. Steel pipe was used as a control. Fig. 1 is a schematic diagram of the apparatus showing the relative position of the separate units making up the equipment. In order to facilitate the installation and removal of the test pipes in the apparatus, O-ring seals capable of sustaining pressures of 50 psi were provided at each end. Test pipes were submerged in a cold water bath maintained at or below room temperature by circulating water through copper cooling coils packed in ice. A hot water bath equipped with immersion-type heaters, stirrers, and a thermoregulator was used to maintain the temperature of the oil prior to introduction into the piping manifold. The capacity of the oil reservoir was 30 gal. A 33-gal/min centrifugal pump, capable of producing turbulent flow velocities in the test pipes, was used to circulate the oil through the system when using %-in. pipe; and a 70-galjmin centrifugal pump was used in later tests using 2-in. pipe. A by-pass arrangement made it pos-

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral-property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive-industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN `01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN '01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB were expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2003

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By Steven D. Knudsen, Dale S. Preece

Computer modeling of the blasting process can aid in gaining an understanding of the physics controlling the process. The sequence of events in a blast occur so rapidly and in such a violent environment that measurements are still difficult to obtain. Computer modeling using a program such as DMC [Taylor and Preece, 1989a, 1989b] can provide insights into the physics of the rapid and violent events associated with a blast. DMC has been used to simulate crater blasting @‘teece, 199Oc] and the blasting of Oil Shale for modified in-situ retorting [Freece, 1990a, 1990b]. This paper will address the influence that damping has on the velocity distribution in the rock mass during the rock motion phase of a blast. Since velocity distribution is a controlling factor of muck pile shape, damping also conbibutes to muck pile shape.

Jan 1, 1992

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By W. -S. Hwang, R. A. Stoehr, P. Ingerslev

"The flow of molten metal entering complex two-dimensional foundry molds has been modeled using the Simplified Marker and Cell (SMAC) and Solution Algorithm (SOLA) techniques. The molds were for a series of four and three-spoke wheel designs. The computer calculations were compared to physical experiments in which molten cast iron was poured into C02-bonded sand molds. The metal was photographed with a high speed motion picture camera focused through a Pyrex glass window on one face of the mold. To get good agreement between the calculations and the experiments, it was necessary to accurately represent the velocity through the ingate. This was calculated by application of the Bernoulli equation to flow through the feed system. Some difficulties were experienced with mathematical instability, expecially in the three-spoke design with a narrow ingate. This was overcome by using 100% upwind differencing, and over relaxation parameter near 1.0 (i.e. no over relaxation), and variable mesh spacing.IntroductionModeling the flow of molten metal entering molds has the potential for making significant contributions to the design of feed systems. It will supply information to the computer-aided-design systems of the future that will enable the designer to optimize the placement of gates, dimensioning of passages, and designation of casting speeds. Such design criteria have generally been based on application of energy balance (Bernoulli equation) principles to flow in the sprues, runners, and gates. Indeed, this is the easiest way to determine the proper dimensions to give a suitable filling time for a casting of a given size. A number of computer programs, including one by some of the present authors, have integrated such calculations into CAD systems. l Modeling the flow of metal inside the mold cavity requires other techniques that will handle free-surface transient flow. Stoehr and Hwang reported on the application of the Marker-and-Cell (MAC) technique to mold filling problems at the previous conference in this series at Hennicker, N.H. in 1983. 2 Although considerable progress has been made since that time in improving the accuracy, stability, and convenience of these techniques, the shapes to which they were applied remained limited. Also, physical verification of the results of the calculations was limited to water models.The work to be reported in this paper was undertaken with two objectives: (1) to apply these techniques to more complex and realistic shapes, and (2) to verify the results by comparison with flow patterns observed in molten metal poured into actual sand molds."

Jan 1, 1986

By J. Howarth

Two electrochemical processing methodologies have been used to electrogenerate bromine-laden solutions for gold-leaching purposes. In the first process, a laboratory-scale cell in which the anode and cathode compartments were separated by a cation-exchange membrane was employed. The bromine produced by electrolysis of a 4% bromide solution was used to leach gold from a low-grade ore. The pregnant leach solution was then returned to the cell to recommence the cycle. High current efficiencies (90-93%) were maintained over six cycles. In the second process, an undivided hypochlorite generating cell (Chloropac"') was used to generate bromine from a simulated leach solution. Electrolyses were performed on a pilot-scale (100-150 gallons) with solutions containing different levels of bromide ion. The current efficiencies were also high (80-90%) and unaffected by the bromide concentration (over the range 2.5-5%) provided the electrolysis was run to low conversion « 15%). The Chloropac module was capable of delivering 0.6 kg bromine per hour at a power cost of $0.09 per kg. Using these figures, a detailed economic assessment for a 1000 metric tonnes (MT) per day gold ore processing plant was made. Electrolytic regeneration of bromine in a gold leach/recovery circuit dramatically improves the process economics over cyanidation.

Jan 1, 1991

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022