Search Documents

By R. R. Klimpel

In three recent publications, Klimpel et al (1988) and Klimpel and Hansen (1988, 89), the theory and invention process behind the identification of two new classes of sulfide mineral collectors were summarized. These two new families can be represented by the 111 generalized formulate: R1-S-R1 -NRI III (denoted as the F-series chelation family) and R-S-R or R -CHSCH-R (denoted as the S-series redox family). The influence of systematic changes in the various R groupings on laboratory batch flotation cell tests has been covered in the above references and will not be repeated in this paper. In particular, the recent article by Klimpel and Hansen (1989) should be studied as a research introduction to this paper.

Jan 1, 1989

A number of gases, such as carbon dioxide, methane, water vapour, nitrous oxide, ozone and chlorofluorocarbons are transparent to incoming short-wave radiation, but are relatively opaque to outgoing longwave radiation. Variations in the concentration of these gases in the troposphere can alter the thermal balance of the earth's atmosphere. Outgoing terrestrial radiation which would otherwise escape to space, is trapped within the inner layer of the atmosphere, resulting in a greenhouse effect. It is estimated that at present greenhouse gases other than carbon dioxide, contribute about 50% to the greenhouse effect. However, in the future, the contribution made to the greenhouse effect by gases other than C02 will become increasingly more significant. Greenhouse gases arise from a wide range of sources and their escalating increease is largely related to an increase in the world's population, an increase in the standard of living of many areas and changes in lifestyle. The effect of increasing man-made greenhouse gases in the troposphere is unknown but it is proposed that it may increase temperature and may modify climate, agricultural response and land use. The sources of greenhouse gases are identified and found to comprise a wide range of activities. The contribution that coals use makes to the greenhouse effect is examined in detail. It is concluded that coals total contribution is small being about 10% of man made greenhouse gases. Envisaged expansion of coal's use will only cause a small increase in greenhouse gas emissions. Whilst developing technology for coal's use for power generation has the potential to reduce greenhouse gas emissions from new plants by approximately 25%.

Jan 1, 1989

By B. S. Van Gosen

In recent years, U.S. regulatory agencies have placed emphasis on identifying and regulating asbestos dust exposures in the mining environment, with a particular focus upon industrial mineral deposits in which asbestos occurs as an accessory mineral. Because asbestos minerals form in specific geologic environments, only certain predictable types of industrial mineral deposits can potentially host asbestos mineralization. By applying a basic knowledge of asbestos geology, the costly and time consuming efforts of asbestos monitoring and analyses can be directed towards those mineral deposit types most likely to contain asbestos mineralogy, while saving efforts on the mineral deposits that are unlikely to contain asbestos. While the vast majority of industrial mineral deposits in the Western United States are asbestos-free, there are several types that can, in some instances, host asbestos mineralization, or be closely associated with it. These industrial mineral deposits include a few types of aggregate, dimension, and decorative stone, and some deposits of chromite-nickel, magnesite, nepheline syenite, olivine, rare earth elements, talc, vermiculite, and wollastonite.

Jan 1, 2009

By S. K. Varma, Miriam Regalado, Daniel Salas, Erica Corral, Erika Esquivel

"Age hardenable 2014 aluminum alloys and composites containing 0.10 and 0.15 volume fractions of alumina particles (VFAP) have been solutionized at 540 and 550°C for up to 20 hours. The solutionized samples, heat treated for 5 and 20 hours, have been subjected to room temperature rolling until cracking develops. The work hardening curves have been compared to determine the effect of solutionizing time on the rolling characteristics from both hardness and the microstructural evolution points of view. Solutionizing at two different temperatures results in differences in the extent to which the composites can be rolled until fracture. The microstructural characterization by TEM has been performed to understand the room temperature rolling behavior.IntroductionThe effect of solutionizing on the age hardening response of 6061 and 2014 aluminum alloys and composites reinforced with 0.10, 0.15 and 0.20 volume fractions of alumina particles (VFAP) have been reported in the literature [1-4]. A comparison of the monolith and composites indicates that particles promote the aging process through differences in the microstructures in solutionized condition. The first effect of solutionizing is to produce a grain growth process which follows a grain growth law (square of grain diameter as a function of solutionizing time). It appears that it is possible for vacancies to be emitted during grain growth period as they try to minimize the total grain boundary surface area by increasing their diameter. This may be common to both the monolith and the composites. However, the second effect must be exclusively considered for the composites. The particles generate dislocations during the solutionizing process due to the differences in the values of the coefficient of thermal expansion (CTE) between the particles and aluminum base metal. It has been determined [1] that the dislocation density increases with increase in solutionizing time in the composites of 6061 aluminum alloys reinforced with 0.10, 0.15 and 0.20 VFAP. The improved bonding between particles and matrix can give rise to additional generation of dislocations due to curvature effects [1] with the result that the dislocation density continues to increase with increase in solutionizing time even after the CTE effect is considered to have been stabilized."

Jan 1, 1998

By V. Vergara

Four copper composites were obtained by mechanical alloying, using as dispersed phases of four carbide powders; they were: boron carbide, chromium carbide, silicon carbide and zirconium carbide. The purpose of this work was to study some characteristics of these compounds and their feasibility for use as materials for electrical equipment. Raw materials used were copper powder finer than 150 mesh, and 2-4 vol % of powder carbides finer than 325 mesh. The alloying process was carried out using both a Spex 800-D mill with tungsten jars and balls and a hardened stainless steel jar and balls, the purpose of which was to measure the degree of contamination induced by the milling media. The changes in particle size, morphology and microstructure of copper alloys were studied with SEM and TEM for each alloyed powder. The degree of saturation of copper by the carbides was measured by X-ray diffraction. Sound samples were obtained by hot isostatic pressing at 1073°K. The best characteristics were obtained for the compound copper-chromium carbide, based on their hardness, tensile strength and electrical conductivity values. The other alloys failed due to their excessive brittleness after hot pressing.

Jan 1, 1999

By Craig Ammar

JAMIE DAVIS: Our next speaker is Craig Ammar. He's director of equipment management for Cyprus Climax Metals Company. He has, prior to this assignment, been responsible for maintenance at Bagdad Copper, Cyprus' Miami smelter, and Thompson Creek. Like Jerry, he's very shy and retiring, and doesn't have any strong opinions about maintenance. INTRODUCTION CRAIG AMMAR: The ultimate goal behind implementing a proactive equipment management process is to provide capacity assurance and ultimately increase an organization's ability to generate revenue while reducing operating costs. Targeting such lofty objectives has brought many an organization to its knees, utilizing new maintenance techniques, concepts, and technology aimed at making our lives better and more organized. The root cause of such frustration generally stems from a lack of understanding or support for the fundamentals of implementing a proactive equipment management process. There are just two types of maintenance programs, reactive and proactive. It's an established fact that you need a little of both to run an effective equipment management process, obviously more of one (proactive) than the other. Here are some telltale signs that your equipment management process is in trouble: -Maintenance is performed as a knee jerk reaction when equipment fails. -Repeated and frequent equipment failures occur, with no focus on eliminating the root cause. -Sketchy, inconsistent, unclear preventive maintenance is performed or there is no support for the preventive maintenance process. -No predictive maintenance technology process is in place, or little support for predictive maintenance exists. -Less than 50 percent of your work is generated by the maintenance group resulting from inspections.

Jan 1, 1998

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. ' In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By Paul Billingsley

THE purpose of this paper is a comparison, based on genesis, of the ore deposits associated with the igneous rocks of the central Montana Rockies. Considered separately, without attention to their origin, the orebodies appear to be distributed haphazard, with no fundamental laws controlling their position and character. It is believed, however, that if all the factors be weighed, this apparent confusion will to a large degree disappear. The, first essential to such a comparison is detailed knowledge of the individual mines, as to their geographic position (see Fig. 1), their mineralogical character, and in particular the derivation of their ores.1 The authors of this paper have pursued such an investigation for the past 6 years, and have accumulated a mass of evidence that enables a preliminary correlation to be attempted. It appears that the majority of ore deposits are genetically related to one or another of the igneous

Jan 4, 1917

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By Finley A. Campbell

"Nickel-copper sulphide deposits associated with basic rocks in the Quill Greek area and the White River area in the Yukon Territory have been studied and compared from the view-point of their general geology, structural geology, and the mineralogy of the ores. The relative amounts of the major constituents, magnesium, iron and calcium, and the minor constituents, nickel, cobalt and chromium have been determined spectrographically for two cross sections of the basic rocks at Quill Creek and one at White River. These data, along with petrologic and field evidence, were used to determine the sill and dyke-like character and nature of the basic intrusions. Loss on ignition is employed as a measure of the degree of serpentinization. The distribution determined shows that the serpentinization does not appear to have greatly influenced the inferred original distribution and lithophile associations of magnesium and nickel. The cobalt content may have been altered.The nickel content of the serpentinized peridotites ranges from an average of 0.36 per cent in one section to an average of 0.24 per cent in each of the other two sections studied. The cobalt averages 0.0038 per cent in the samples from the two Quill Creek sections and averages 0.0042 per cent at White River. These results have been compared with other available data.The sulphide ores are later than both the peridotite and gabbroic rocks and may be co-magmatic with them. There is no evidence in these areas to support an origin by lateral secretion; on the contrary, the alteration associated with the ores, the mineralogy and spatial relationship to basic and ultrabasic rocks, indicate the ores are derived from a basic magma."

Jan 1, 1960

By Steven Tubbs

Steven Tubbs From mine to farm is a long journey for Florida's phosphate, but it is an important one to the American farmer who uses phosphate fertilizers to replenish the soil and produce the crops which eventually wind up on the American dinner table. In this phosphate-food connection, transportation plays a vital life-giving role, a role that is unique because of the large quantities of phosphate produced and the mineral's location in relation to its markets. Florida Leads World Florida is the world's largest phosphate producer, supplying 80% of the nation's and a third of the world's annual total. About 95% of Florida's phosphate goes into agricultural chemicals, with 90% going into fertilizers. Phosphate production is primarily concentrated in west central Florida, with the exception of mining and processing in north Florida by Occidental Chemical Co. The phosphate rock is beneficiated at the mine sites and then is transported out of Florida in a raw state, or to one of the industry's 18 chemical complexes where it is processed further. In 1981, Florida produced more than 42 Mt (46 million st) of phosphate rock-a 1% decrease from 1980. The industry also produced more than 12 Mt (13 million st) of phosphate chemical products in 1981 and transported them to both domestic and foreign customers. This year, the state's phosphate production and shipments are substantially lower than recent annual levels because of a depressed worldwide phosphate market. With production down slightly in 1981, shipments declined and company inventories increased dramatically. Phosphate-related shipments through the port of Tampa alone fell 20%. As a result, in 1982, phosphate operations cut production to reduce inventories. According to the Fertilizer Institute, during the fiscal year ending June 30, 1982, phosphate rock production fell 18%; phosphate rock shipments, 28%; finished fertilizer production, 30%; finished fertilizer shipments, 25%; and phosphate rock exports declined by 20%. Despite depressed conditions, Florida phosphate production and shipments are expected to increase in the near future with more rock being processed into fertilizer products. Phosphate is one of Florida's major industries. The US Bureau of Mines estimates it contributed $3 billion to the state's economy in 1981 and an additional $1.4 billion to the US economy. In addition, phosphate exports contributed to

Jan 10, 1982

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title 11, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By E. J. Gleim

Many people consider the mining of coal to be an extremely hazardous occupation; but it should be remembered that most large industries have to meet special conditions which, if not dealt with properly, might become hazards to life and property. Mining men may not always be fully aware that some practices and certain equipment that is incorrectly designed or maintained can lead to dangerous conditions. In endeavoring to help the coal-mining industry to prevent accidents and disasters, the Bureau of Mines has engaged in a program of education on conditions and practices that must be avoided. An effective way to teach safety is by visual demonstration. For example, it is generally known that certain kinds of electrical flashes have ignited explosive atmospheres in mines, but actually to see and hear explosions caused by electrical sparks of different size and character under laboratory control is likely to teach a much more emphatic and lasting lesson than would be learned by merely reading about them. The interest manifested by those who witness the demonstrations seems to prove that this is true. The purpose of the demonstrations is not to discourage the use of electricity in mines, but rather to indicate what types of equipment (including some generally regarded as harmless) can ignite gas and what safeguards have been developed to prevent such ignitions. It is hoped that this information will improve the ability of mining men to cope with underground hazards.

Jan 1, 1937

By A. A. Berk

In the course of a study of the formation of external deposits on tubes in water-tube boilers it became desirable to determine the sulfur dioxide (SO2) and sulfur trioxide (SO3) in the Due gases. Determinations made by the A.S.M.E. method for SO2 and SO3 in gaseous products of combustion did not give accurate results. It was found that minute quantities of copper, present in the flue gases from the coal in use, caused oxidation of sulfite in the absorption bottle and that the carbon dioxide (CO2) in the flue gases caused high values for SO2. The A.S.M.E. test procedure was revised to prevent oxidation of sulfite in the absorption bottle and to allow for the effect of CO2; subsequent analyses of flue gases produced reliable results. The revised procedure is described.

Jan 1, 1950

By Robert P. King

In April, 1975 the Colorado School of Mines began monitoring rock mass response associated with a long- wall shield demonstration project near Raton, New Mexico. This project was sponsored by the U. S. Bureau of Mines (DOE) and performed at Kaiser Steel Corporation's York Canyon Mine. Two of the results of the intensive instrumentation effort are the empirical subsidence and horizontal strain models presented herein. These models are based on data gathered during mining three adjacent longwall panels (4N, 5N and 6N). A total of 251 permanent surveying monuments were monitored over the three-panel area. Lines of monuments were oriented along panel centerlines, perpendicular to centerlines and diagonal (45O) to centerlines. Active monuments were monitored twice a week, with less frequent monitoring of stable or slow moving monuments. Primary subsidence monitoring equipment consisted of an AGA Geometer Model 75 and a Wild T-2 Theodolite with -a Wild-Sercel DI-3S distomat.

Jan 1, 1979

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By S. J. Rodgers

MSA Research Corporation, Division of Mine Safety Appliances Company, was awarded a contract to conduct a survey of past and present methods used to control respirable dust in noncoal mines and ore processing mills. The survey covered information reported in mining journals, and U.S. Bureau of Mines Circulars, dust inspection reports, on-site evaluation of dust control methods and systems, and contact with manufacturers of dust control equipment. Both surface and underground mining operations were visited. Fifty mines and 51 processing plants were included in the survey. Dust control methods for the following types of ores or mines were studied: [ ]

Jan 1, 1974

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999