Search Documents

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By A. V. Deforest, C. W. Macgregor, A. R. Anderson

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By I. M. Ritchie

Cyanide owes its great success as a lixivant for gold to the great strength of the Au-CN bond. A replacement for cyanide must similarly be a strong complexant for gold (I) or gold (III). The various alternatives are briefly considered and it is concluded that only thiosulfate has a reasonable chance of replacing cyanide as a relatively non-toxic lixivant at the present time. However, there are considerable technical problems to be overcome before thiosulfate can be considered to be a realistic alternative to cyanide. Firstly, the leaching of gold using aerated ammoniacal thiosulfate with copper as a catalyst is a complex process which needs to be understood and controlled carefully in order to achieve maximum recoveries with minimum reagent losses. Secondly, there needs to be an option similar to the CIP process for recovering and concentrating the dissolved gold thiosulfate complex from pulps produced in the processing of low grade gold ores. The prospects for overcoming these technical' challenges are evaluated and discussed.

Jan 1, 1998

By Afonso Garcez de Azevedo, Anna Carolina Lopes Rabello, Renan Tavares Vicente, Sergio Neves Monteiro, Amanda Maia Ferreira dos Santos

Civil construction is a sector of extreme impact in the Brazilian economy, with construction and demolition waste (RCD) having an extreme impact on the amount of urban solid waste. In this research it was proposed to propose a way of using these residues in the construction of concrete artifacts for structural use. Concrete specimens with sand substitution by RCD were produced in different percentages as a way to contribute to reduce,recycle and reuse thi large amount of waste from the construction industry. The objective of this work was to study the mechanical properties of structural concrete with total and partial replacement (25, 50, 75 and 100%) in sand mass. The results of the compression test indicate good quality for concretes with mass substitution of up to 75% per RCD.

Mar 1, 2018

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magneto-hydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2014

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

By R Price

"Technology has the potential to revolutionise industries, work functions or businesses. One such technology in the mining industry is the deployment of automation in a modern autonomous haulage system (AHS). This paper examines a theoretical application of an AHS in a medium scale mine site. The cost-benefit commercial argument is particularly compelling, and the paper outlines metrics and future issues for consideration.Citation:Price, R, 2016. Autonomous Haulage Systems - the Business Case, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 11–17 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Moe Momayez

Shotcrete is a practical and economical support system in many Canadian underground mines. Although shotcrete technology has gained acceptance in the mining industry, there are some problems that have emerged with respect to quality assessment and thickness measurement of the liner. This paper presents recent tests performed with a miniature seismic reflection device developed primarily for thickness measurement of this heterogeneous liner. Work was performed on site in an underground mine in Ontario, Canada. This paper also presents the results from laboratory tests performed on fibre reinforced and non-reinforced shotcrete panels that were used to assess the P-wave velocity in both materials. The results of these tests were used in a second on site investigation. The NDT thickness measurements showed good agreement with direct thickness measurement such as coring.

May 1, 2001

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By A. Iván, Patiño C. Francisco, Flores B. Javier, Peréz L. Miguel, Hernandez A. Juan, Trapála P. Norma, Salinas R. Eleazar, Rivera L. Isauro, G. Flores, U. Mizraim

"Tills work is related with the production of tiles using wastes from mining and metallurgical industry of Hidalgo State, as raw material. These wastes present a majority particle size (60 %), minor than 53 m (mesh 270, in Tyler Series) with the following composition; 70.01 % wt. of Si02, 12.82 % wt. of Ah03, 3.80 % wt. of Fe, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 grams per ton of Ag and 0.6 grams per ton of Au. In this work, the partial results and experimental conditions for the preparation of some composites to produce tiles are shown. The composite that offers the best results in productions of tiles was that with 66.67 % wt. of mining waste, 26.67 % wt. of red mud and 6.67 % wt. of black mud.IntroductionTo now, mining activities carried out during more than 457 years in Hidalgo State, Mexico; has lead a great volume of wastes; which can be classified into different types, having among the more common; Acid mining water, solid transport water, elements in radical form, abandoned minerals without processing and processing minerals wastes known as burrows, being these the most abundant in the region counting with an approximated volume of 110 million of tons, presenting a fine particle size that can affect population health during windy epochs [1 -4].Form metallurgical point of view, is well known that a fundamental characterization study it is necessary to know the viability of reusing or recycling of these wastes. According this, these residues can also be considered as raw materials in other economical activities, due its Si, Fe, AI, Ca, Na and P oxides contents, its mineralogy and the distribution of chemical elements in the primary and secondary phases [1,2,5,6]."

Jan 1, 2012

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA's technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023

By J. D. Verhoeven

The effectiue distriblltion coefficient has been Measured in a series of vertical, normal freezing experirtzents with large current densities passing through the solid-liquid interface. The results indicate that the effect of the current on solute redistribution is due to electvotransport in the liquid. The high currents produced extensive mixing in the liquid which was considerably reduced by solidifying in small lubing. Analysis of the convection indicates that it probably vesulls from a horizontal temperature gradient produced by the Joule heating- of the electvic crirver~t. Due to the strong dependence of this convection upon the specimen radius, it is conclnded that only for specit~ens with radii of less than somewhere between 1 and 2 mm wilt electric field freezing be getlerally effec-tire at enhancing the purification of zone-melting experittierats in loe-melting alloys. Experiments on 0.8-mm lubes illustrate some interesting potential applications of this techniqne as a means of solute control on smcrll specimens. In a number of papers published within the last few years'-4 it has been found that passage of large dc currents through the solid-liquid interface of a freezing alloy produces a change in the solute redistribution accompanying the solidification. It had been predicted theoretically by Hucke et al.s and by Pfann and Wagner that such an effect would occur as the result of electrotransport within the liquid boundary layer at the solid-liquid interface. These authors independently derived the following relation between the effective distribution coefficient and the variables of the process: Where k0 is the equilibrium distribution coefficient, V is the mobility of the solute relative to the solvent, E is the electric field intensity, D is the solute diffusion coefficient, R is the rate of interface motion, and 6 is the boundary layer thickness. Both groups of authors show that this equation predicts the possibility of extending the purification ability of zone-melting experiments by the addition of an electric current. However, there are other effects in addition to electro-transport which could be produced by the high dc current and might, perhaps, invalidate the applicability of Eq. [I]. For example, high electric current might affect the interface reaction or perhaps the equilibrium distribution which was assumed to exist at the interface. It was the purpose of this work to determine the applicability of Eq. [I] by systematically investigating a simple system for which all of the necessary parameters were known. It was of particular interest for speculating on the potential usefulness of this technique to determine the maximum practical field intensities obtainable, and the effect of these high fields upon convective mixing in the liquid. The initial work in this study was published in a previous paper3 which will be referred to as I. In that work, a current density of 2000 amps per sq cm was used with specimen diameters of 5 mm. The results gave a qualitative confirmation of Eq. [I.], and also showed that a large amount of convective mixing was produced in the liquid by the current. The present study is an extension of that work to smaller specimen diameters and higher current densities. Two points were overlooked in I and will be emphasized here: a) the value of ko has not been well-established in the Sn-Bi system and b) the observed convection could be due to thermal convection produced from the Joule heating. EVALUATION OF k0 To evaluate Eq. [ I.] it is necessary to know the value of the equilibrium distribution coefficient, k,. Tn I the value of k, was taken as 0.3 from a published phase diagram.7 According to ansen' the best data on the phase boundaries of the Sn-Bi system are those of Davidson.5 The data of Davidson give a k, value ranging from 0.21 to 0.25 for the compositions studied in this work, or an average value of around 0.23. In a recent publication, Rigaud and Tougas'10 determined ko by means of a solidification technique. For an alloy of approximately the same composition as that used in this work they obtained a ko value of 0.39. Hence, there is considerable uncertainty in the value of ko and, consequently, a series of experiments were made to determine k, more accurately.

Jan 1, 1968

By McHenry Mosier

A skull breaker has demonstrated its advantages for secondary breaking in a limestone quarry by entirely displacing secondary blasting . It has reduced safety hazards to workmen, increased the number of quarry operating days , and has lowered mining costs by 2.7 cents a ton. It is believed that the application of the skull breaker can be made economically advantageous in the surface mining of other commoditics .

Aug 1, 1948