Search Documents

By R. V. Lundquist, H. Leitch

The solubility characteristics of three calcium aluminates , 12Ca0 · 7A120½ 3Ca0 A1203 , and 4Ca0 A12 03 Fe2O3 , were determined in water and in solutions of NaOH and Na₂ CO₂ to more clearly define their role in relation to the recovery of aluminum by the lime sinter and the lime - soda sinter processes . The calcium aluminates were prepared by sintering stoichiometric mixtures of CaCO3 , Al2O3 3H20, and Fe 0 at 1,375 ° C. The rates and extent of aluminum extractions were determined . The aluminum extractions from the aluminates were dependent on the presence of carbonate ions in the leach solutions , temperature , time , leach solution composition , and solid - liquid ratio of the slurry . The aluminum extracted from the calcium aluminates in water and in NaOH solutions varied from 4.6 to 22.9 percent . Virtually , complete extraction could generally be obtained for 12Ca0.7A120 and 4Ca0.A12 03 • Fe₂ 03 ; in one instance it was obtained for 3Ca0.A1203 , when an excess of carbonate ions was present over that required for the conversion of all of the calcium in the aluminates into CaCO3 . In some cases of poor aluminum recoveries , extractions could be improved by regrinding and releaching the solid residues .

Jan 1, 1964

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By John Hoelle

Coal mines in southern West Virginia, south-western Virginia and eastern Kentucky have experienced coal bumps at least since 1933. Most of the bumps have occurred due to high cover, strong roof and floor strata and stress concentrations due to the mining sequence. A longwall mine in eastern Kentucky first experienced coal bumps on the tailgate side of the longwall face in 1989. The bumps continued until 1996. The bumps were the result of: Thick overburden up to 2200 feet Strong roof and floor (strata strengths up to 25,600 psi UCS and elasticity modulus up to 4,800,000 psi Previous over-mining in places Sandstone channels Not all characteristics occurred simultaneously. The bumps produced seismic events recorded up to 4.3 (Richter scale magnitude), and damaged pillars that were up to 147 by 152 feet in size.

Jan 1, 2008

By S. Montes

Mineral floatability is strongly connected with mineral structure and composition. The complexity of mineral surfaces has meant that few attempts have been made to understand the effect of impurities (trace elements) on the flotation process. Zeta potential technique has been extensively used to evaluate the surface charge of mineral particles. Nevertheless, those measurements consider only an average of mineral particles surface charge. The presence of fine particles and inclusions covering a mineral may influence the local reagent adsorption process, which will ultimately be reflected in the subsequent global response of the mineral froth flotation efficiency. The current work assesses the iron oxide mineral, haematite (Fe2O3). Zeta potential and streaming potential techniques were used to determine the surface charge of fine and coarser particles of haematite. Further analysis was performed to determine the point of zero charge (PZC) of the mineral. In addition, adsorption isotherms of alkyl ammonium chloride reagents with different lengths of carbon chains were carried out. It was found haematite floatability depends strongly on the isoelectric point (IEP) value, which is affected by other mineral species present at the mineral surface. Haematite floatability became significant only at relatively high tetradecyl ammonium chloride collector concentrations (concentration greater than 4 10-4M), which does not happen with other oxides such as quartz. Unlike quartz, haematite develops a low surface charge over a wide range of pH, disabling all long-range attractive interactions between the mineral and the collector. Therefore, hydrophobic chain interaction is probably the most likely mechanism acting to promote collector adsorption and enhance further floatability. Diffused reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to suggest a possible mechanism to understand the sequence of collector adsorption and the effect of trace species on it. Keywords: floatability, haematite, adsorption, electrochemistry, zeta potential.

Jan 1, 2007

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992

Preparing for automated sample preparation has two facets; the need for better procedures as seen by the laboratory Manager and the approach to be adopted as envisaged by the equipment manufacturer. Both have many options and during the 1990s some at least of these options will be tried. As automation of sample preparation is only just beginning, can it be said that there is a real need for better procedures. What does automated sample preparation have to offer? Does it have real advantages or is it just a marketing tool to sell equipment?

Jan 1, 1976

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

PRESIDENT LITTLEJOHN: The paper of Mr. Emrick will now be open for discussion for about twenty minutes. The meeting is now open for discussion. MR. EMRICK: There is some question that may have occurred to you at different times, that is how are you going to tell when the bits are properly made? A fairly good rule to go by is when the used bits come out of the mine, if half of them are bent and half of them are broken, the average is pretty good MR. GEO. B. PRYDE (Union Pacific Coal Company): I would like to ask Mr. Emrick if he has any figures as to the saving of Dower with the different styles of its. MR. EMRICK: I suppose you mean chisel point bits and pick point bits? MR. PRYDE: Yes. MR. EMRICK: So far as I have been able to learn, the only reason why chisel point bits are used is to prevent coring that might be done by the cutter chain. The pick point bit, of course, is the proper thing to use. It can be used when the position of the cutter links in the cutter chain is right. I do not know of any figures which give power consumption ratings on the use of pick point and chisel point bits, but there are tests and ratings, etc., which have been taken- which have been tested as against different bits, which have been given proper clearances against bits not having been given proper clearances, and they will run,-in their saving in power, they will run 20 to 25 per cent. MR. A. C. WATTS (Chief Engineer, Utah Fuel Company) : I would like to ask Mr. Emrick if he has any record showing the saving in power on using the alloy steel chisel bits. I know that several experiments have been made; I do not recall the figures now, but we had a very decided saving in power. MR. EMRICK: I haven&apos;t any of the records. Do you think that is because of the steel that has been used? MR. WATTS: Well, they were all sharpened by the same man and used in the same machine, and at the same shop. I do not know the composition. It is "Red Star" Vanadium that I had in mind. MR. EMRICK: I have not seen any records. Some companies are using the tool steel bits because they stand up a little bit better. MR. BENEDICT SHUBART (Secretary) : I was going to ask Mr. Emrick about that question. There is one company that does not recommend tempering the bits. They recommend using not exactly self-hardening steel, but one that is bard enough without quenching-they use 80-90-point car- bon but about a 70-point manganese, not exactly self-hardening steel, but they do not temper this at all. Will Mr. Emrick state if a steel of that kind could be worked in the bit sharpening machine that his company makes, as it

Jan 1, 1925

By Rolf B. Pedersen, Ana Filipa Marques, Ingunn H. Thorseth, Ingeborg Okland

"Deep sea mining of polymetallic sulphides will change the physical and chemical conditions at the seafloor by creating scars when sulphides are removed, and potentially also by deposition of mine tailings at the seafloor. These changes will impact the existing ecosystems at the seafloor in and around the mined areas. Seafloor Massive Sulphide deposits that have been exposed to oxic seawater weather into Fe-metal-oxyhydroxides. However, the rates of weathering and release of heavy metals and other toxic compounds to the environment from freshly exposed sulphides in a deep-sea environment are not well studied.During a cruise to the Arctic Mid-Ocean Ridge in the Norwegian-Greenland Sea in July 2014 we will initiate in-situ experiments investigating the microbiological and geochemical processes involved in the weathering of freshly exposed massive sulphides deposits in a natural environment. This will be done by creating scars in naturally occurring sulphide deposits and by deploying weathering experiments at the seafloor. The sites will be revisited and re-sampled in 2015. The mobility and fate of heavy metals will be one of the main concerns of the study as well as constraining the time it will take for exposed sulphides to return to the chemical state present prior to mining. In this presentation we will present the experimental framework and the preliminary results from the July 2014 cruise. This project is part of the EU funded MIDAS (Managing impacts of deep sea resource exploitation) project."

Sep 1, 2014

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy&apos;s law for fluid transport, can be written as:

Jan 1, 1967

By Winthrop P. Haynes

The symposium on production for the year 1943 contains few papers on the foreign situation. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. A noteworthy feature of the reports on Texas this year is the map on page 469, which shows the districts covered by the statistics. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author&apos;s best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determina-tion. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are suficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on &apos;&apos;Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can be calculated by those interested from the figures given. In classifying wells as to producing methods, enter all wells that are not "flowing" in the column headed "Artificial Lift." If possible, add footnotes to indicate whether the lift is "pumping," "gas lift" or "air lift."

Jan 1, 1944

By Winthrop P. Haynes

The symposium on production for the year 1943 contains few papers on the foreign situation. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. A noteworthy feature of the reports on Texas this year is the map on page 469, which shows the districts covered by the statistics. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author&apos;s best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determina-tion. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are suficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on &apos;&apos;Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can be calculated by those interested from the figures given. In classifying wells as to producing methods, enter all wells that are not "flowing" in the column headed "Artificial Lift." If possible, add footnotes to indicate whether the lift is "pumping," "gas lift" or "air lift."

Jan 1, 1944

By Richard H. T. Garnett

The first, profitable, marine placer mining started with tin 100 years ago but no major industry developed until the mid-20th. Century. Dredging at sea yielded cassiterite in both South Thailand and Indonesia, and remains an important state-run industry in the latter country. Malaysia and Russia have also contributed production, and the coastal waters of Tasmania and England have been explored. Marine placer deposits of gold have been examined in New Zealand, Chile, Argentina, Russia and West Africa. Philippino deposits were dredged during the 1930s. Fifty years later, at Nome in Alaska, gold was recovered by dredging from the offshore, and the technical/economic benefits of a seabed-deployed crawler were first demonstrated. Off the coast of Namibia placer diamonds were recovered by airlift mining during the 1960’s, but De Beers effectively started the existing marine diamond industry in 1989. The Wirth drill and a crawler continue to be used by the company, and plans recently have been announced for operations in South African waters. Other commodities such as mineral sands, platinum group minerals, and chromite have been investigated offshore in several worldwide localities.

Aug 24, 2006

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

"It is projected that the reactivity of acid generating tailings and waste rock can be minimized by reducing the access of oxygen by placing these materials under water in natural or manmade lakes. A project under the MEND and B.C. AMO Task Forces has been in progress for four years to evaluate active and historic tailing sites in B.C. and Manitoba. The sophisticated geochemistry studies conducted on the interstitial pore water has illustrated encouraging results which are discussed. The additional studies which are needed to complete the scientific database for the study sites, for achieving regulatory and public approval and for the engineering of application of this method of control are outlined.IntroductionWorld wide research effort is in progress to find the solution to the acid mine drainage problem. A great deal is known about acid mine drainage but much work is required to find economic and effective approaches to the problem. Two coordinated programs have been initiated recently in Canada: the National Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Drainage Task Force.Disposal of tailings materials under a water barrier such as a natural lake, is thought to be one solution to prevent acid generation by preventing oxygen and bacterial action on the sulphide surfaces. The deposition of reactive tailings materials under water in natural lakes has been used historically at various mines in Canada. However, there has never been a thorough review of the long and short term impacts of historic sites which may provide crucial information to understand the physical, chemical and biological processes which are taking place.This paper provides a general overview of a series of studies which examine the general biophysical characteristics and the sediment geochemistry of four lakes where subaqueous disposal has been or is currently being used for acid generating tailings. The subaqueous disposal studies have been conducted from 1989 through 1991 and were initiated and supported by both research task forces. The objectives of this paper are to summarize the history and the background information of the studies conducted, the general results obtained from each lake, an overview of the major collective results and the additional work which is required to achieve the final objective of developing criteria for applying this technology in the industry."

Jan 1, 1992

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972