Search Documents

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By Hugh P. Nicholson

IN view of the many articles that have been written on the proper classification of mining systems without so far having produced any particular tangible results it might seem that the subject is hopeless of solution. I do not believe that is so, and my intention in contributing the following outline is to present a slightly different viewpoint. Too much attention is often focused on unnecessary details and not enough on general principles. Too much attention and emphasis is often given to the system employed at one particular mine or in one particular district. In addition, names that are entirely misleading are applied to mining systems, and their adoption by the coming generation perpetuates a condition that needs clarification badly. The following classification is the result of several years of practical experience in mining and also several years' practice in teaching the same subject. It therefore represents a broad picture of the entire field of mining systems from the viewpoint of the miner as well as the teacher. It seems that the difficulty in the past has been in reconciling these two viewpoints. The need of such a reconciliation requires no explanation.

Jan 1, 1934

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By Ivan Malinsky, Gérard Castonguay

"On a développé un procédé qui donne une fonte (2,3% C, 0,07% V) du V2O5 (99%) et un rutile synthétique (94% TiO2) à partir d'un minerai, dont les réserves au Québec sont importantes. Le procédé comprend les opérations suivantes: 1) la concentration magnétique du minerai (30% Fe, 9% TiO2 et 0,65% V2O5) pour produire un concentré (65% Fe, 7% TiO2 et 1,6% V2O5); 2) le smeltage du concentré aggloméré dans un four à arc, sans fondant, pour produire une fonte et une scorie (30% FeO, 40% TiO2 et 8,0% V2O5) qui contient plus de 95% du vanadium et du titane présents dans le concentré; 3) le grillage alcalin (37% Na2CO3) de la scorie suivi d'une lixiviation à l'eau et de la précipitation de l'hexavanadate d'ammonium à partir du filtrat; 4) la lixiviation du résidu par l'acide sulfurique pur ou usagé pour produire un rutile synthétique. Un estimé préliminaire de la valeur économique du projet laisse croire à sa rentabilité à la condition que l'investissement pour le smeltage soit inférieur à environ 400$/tonne de fer.IntroductionLes gisements de magnétites titanifères sont nombreux dans le monde. Ils consistent en une magnétite étroitement liée a l'ilménite, La teneur trop élevée en TiO2 empêche l'exploitation de ces gisements pour la production de fer. Cependant, dans certains cas, la magnétite a une teneur intéressante en vanadium qui peut rendre l'exploitation de ces gisements rentable. Aujourd'hui, les magnétites titanifères constituent la plus importante source de production de vanadium. On estime qu'environ 70% du vanadium produit provient de ces sources."

Jan 1, 1983

By Thomas W. Thompson

The Zebulon manganese deposit has been known for a number of years. It is situated about 3 miles east of Zebulon, Wake County, N. C., on the Avon, Privett property (fig. 1). The deposit outcrops as a vein, or dike averaging-16 to 20 feet in width. Drilling by the Bureau of Mines has shown that this outcrop results from consolidation of a number of small stringers near the surface. The surface width and the Percentage of manganese oxides (resulting from. weathering) diminish with depth. Below 50 to 80 feet, the vein material is mainly quartz and spessartite garnet. The deposit was first examined by W. T. Benson, a Bureau of Mines engineer, in 1941. The Bureau conducted a diamond-drilling exploratory program an the property from November 7, 1944, to January 25, 1945. A. total of 2,508.5 feet was drilled in 14 holes along the strike of the deposit.

Jan 1, 1950

Today computers are accepted as a standard item in industry and they perform a variety of tasks over a wide spectrum of activities from mine planning and CAD to data processing and spreadsheet work. However many problems particularly in the. area of decision making where there are no clear mathematical models available and usually the output or answer is dependent to some extent on a heuristic approach, don't lend themselves to conventional solutions using standard procedural algorithms. Recently a number of techniques have evolved primarily from the enhanced capabilities of modem equipment, which are capable of solving these problems. This paper is a brief overview of these rather unconventional developments of computer technology in the area of artificial intelligence with reference to their application in mining.

Jan 1, 1993

By Seung-Kyu Son, Michael T. Chandler, Youngtak Ko, Gyuha Hwang

Over the past decade, sea-floor hydrothermal vent fields have been studied by many researchers because of their commercial potential of mineral resources and the origins of Earth’s life. Approximately 300 of these are reported as massive sulfide deposits near the mid-ocean ridge, most of which are located in the Atlantic and Pacific ridges. However, only fourteen deposits have been identified in the Indian mid-ocean ridges. The Central Indian Ridge (CIR) between 8°S and 12°S is composed of three segments with a slow full- spreading rate of 33-37 mm/yr. The hydrothermal activity at the slow-spreading center can be generated along the ridge axis attended by volcanism or along the tectonic features, such as oceanic core complexes (OCCs). OCC is an exposed mantle rocks composed of peridotite and ultramafic rocks uplifted through long-lived detachment fault processes which can also lead to extensive hydrothermal circulation near the slow-spreading center. Therefore, the identification of OCC’s properties will be an important indicator for finding the sea-floor hydrothermal vents. To study hydrothermal activity of the CIR, Korea Institute of Ocean Science and Technology (KIOST) have conducted expeditions using R/V Onnuri over four years (2009-2011, 2017). High-resolution bathymetry and backscatter data was obtained during expeditions using multibeam echo system of EM120 in 2009-2011 and deep-tow side-scan sonar system of IMI-30, which has more higher resolution than EM120, in 2017. In this study, we use these high-quality data for constraining location and size of OCC. We also analyze the geophysical and morphotectonic characteristics of OCC gathering high-resolution bathymetric map and backscatter image.

Jan 1, 2018

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022

By T. Miura, Y. Mori, H. Aoki

In a flash smelting furnace, easily combustible concentrate particles excessively oxidized and melt. The excessively oxidized molten particles then collide with less oxidized solid ones to create uniform oxidized molten particles. This collision phenomenon plays a very important role in achieving high smelting performance. The authors developed a mathematical model describing above combustion phenomena. This model incorporated fluid flow, heat and mass transfer, chemical reactions and collisions of concentrate particles. Both gas flow and particle motion were calculated using the Eulerian method. Copper concentrate was assumed to consist of chalcopyrite(CuFeS2). Considered in the concentrate reactions were the decomposition of CuFeS2, and the oxidation of the resulting sulfur(S) and pyrrhotite(FeS) to produce magnetite(Fe30 4) and sulfur dioxide(S02). Moreover a reaction due to concentrate particle collisions, in which Fe304 in the excessively oxidized molten particle reacts with FeS in the less oxidized particle, was also considered. The particle collisions were assumed to occur according to a collision probability rule obtained by computational experiments. Particle growth in diameter was described as a change in the volume fractions of particle phases. When applied to a commercial flash smelting furnace, this model reproduced the particle growth and component transfer as observed in the actual furnace.

Jan 1, 2007

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By R S. Sing, M D. Yadav, G Udaybhanu

This paper presents the results of the first part of a research project to study the effect of various inhibitors to reduce the spontaneous heating susceptibility of some highly susceptible Indian coal seams. In this investigation 11 inhibitors were chosen and applied at three, five and ten per cent of their concentrations in an aqueous solution for four coal samples collected from four different seams. The susceptibility of coal samples, before and after application of these inhibitors, was determined by carrying out crossing point temperature (CPT) analysis. The findings of this study have indicated that it is possible to retard the tendency of spontaneous heating of Indian coals to a considerable extent by the application of six of the inhibitors studied. Further, these inhibitors were tested in 1:1 combination to study their synergistic effect. Finally the economics of the application of these inhibitors has been analysed and four inhibitors are recommended for field use. These results have direct application to control fire and improve productivity and safety in coal mines.

Jan 1, 2005

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By Fink ST

Management requires up-to-date information on the activities of an enterprise in order to maintain control and to assist in decision-making and planning. In today&apos;s environment it is essential that this information is immediately available and in an easily assimilated format. If this is not the case, management is forced to make decisions based on intuition and past experience. At Mt Newman Mining Co, a computer application has been developed and implemented with the objective of providing this type of information to management. The Key Parameter Reporting System (as the application is known) allows for daily (constant) on-line capture of selected production statistics, safety statistics and free format textual comments relating to topics such as industrial relations, major maintenance and other pertinent news. Information can be retrieved,&apos;and displayed or printed in either a tabular or graphical format. All senior managers have colour visual display units in their offices for immediate access to the system. Access to selected sensitive information is controlled. All company staff are able to retrieve unsecured information from the system via visual display units installed in all company Locations.

Jan 1, 1983

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995