Search Documents

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011

By Palmer C. Sweet

Kyanite. andalusite, and sillimanite are anhydrous aluminum silicate minerals, and they have the same chemical formula, Al2SiO3. Dumortierite and topaz are also classified as aluminum silicates although they contain boron and fluorine respectively. Mullite (a rare mineral named for its discovery site, the Scottish island of Mull) is produced when kyanite, andalusite, or sillimanite are heated. Synthetic mullite, also classified as an aluminum silicate, is formed by melting alumina and silica, bauxite, and kaolin or alumina, kaolin, and kyanite, depending on the type of synthetic mullite desired. These materials are either sintered in rotary, periodic, or tunnel kilns, or fused in an electric arc furnace. The world's largest producer of kyanite is the United States. Domestic kyanite is presently produced from one company at two sites in Virginia; Kyanite Mining Corporation mines kyanite from Willis Mountain and adjacent East Ridge in Buckingham County in the central Piedmont province of Virginia. Internationally, kymite is produced in Australia, Brazil, India, Kenya, Sweden, and Zimbabwe; the former USSR also produces kyanite (Fig. 1). Andalusite is produced by Piedmont Minerals Company, Inc. in the Piedmont province near Hillsborough, NC. Andalusite is also produced in France, India, the Republic of South Africa, and Spain (Fig. 1). Sillimanite is produced in Australia, Brazil, India, Spain, and the Republic of South Africa; the former USSR is also thought to be a major producer (Fig. 1). Some of the countries produce only for domestic use. Synthetic mullite, made by sintering and by electric arc fusion, is produced by Mulcoa (Mullite Company of America) in Andersonville, GA, and by Washington Mills Electro Minerals Corporation in Niagara Falls, NY. Annual world production of kyanite, andalusite, sillimanite, and synthetic mullite is approximately 672 727 tons (Potter, 1988). GEOLOGY Mineralogy Kyanite is a blue to light-green, triclinic mineral that occurs in long, thin-bladed crystals and crystalline aggregates in gneiss, schist, and pegmatites. The mineral has a hardness of 5 parallel to the long axis of the crystal and a hardness of 7 across the crystal. Andalusite is a yellow, brown, green, or red orthorhombic mineral that occurs in thick, almost square prisms in schist, gneiss, and hornfels. Gem quality andalusite exhibits a strong pleochroism; brownish-green in one direction and brownish-red perpendicular to it. Andalusite also occurs in placer concentrations where it has weathered out of rock. Sillimanite is a brown, pale-green, gray, or white orthorhombic mineral that occurs in long, slender, needlelike crystals in schist and gneiss. Chemical and Physical Properties Chemical and physical properties of kyanite, andalusite, and sillimanite are noted in Table 1. Kyanite is the only mineral that irreversibly expands when heated (calcined to produce mullite) and may offset the shrinkage of most ceramic or refractory ingredients when heated.

Jan 1, 1994

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By James A. Finch, Jason S. Doucet, Cesar O. Gomez

"Exercising control over the physical environment of flotation as a step towards process optimization is the driving force for characterizing gas dispersion in flotation cells, a subject of considerable research and still not fully understood. From an operational standpoint, however, there are just a few variables that can be manipulated to manage gas dispersion on a cell-to-cell basis, the most important being gas rate (superficial gas velocity Jg). Measurements in eight plants demonstrate there is often no strategy for distribution of gas to cells in a bank, i.e., there is no particular Jg profile. Two exercises where Jg profiles were set allowed metallurgical performance to be manipulated and an optimum Jg profile to be selected. To facilitate setting Jg profiles, a multi-unit device based on McGill Jg sensor technology is introduced. Possible directions for gas dispersion management are discussed.INTRODUCTIONThe earliest patents regarding the flotation process ignored the importance of air and in certain cases, steps were taken to eliminate bubbles from the system (Nelson and Smit, 2005). Rickard (1916) described a keen metallurgist who observed better than expected performance and hypothesized that entrained air was enhancing the process. Within a few years of this observation, the basic concept of modern froth flotation was developed whereby air is dispersed into slurry to induce bubble particle contact.As research into flotation advanced, the link between performance and the flow-rate of air entering the cell was established. In the first volume of the International Journal of Mineral Processing, Harris (1974) described the importance of airflow-rate and derived parameters such as the superficial gas velocity (then called the superficial airflow velocity) as being important parameters for cell design and scale-up. Mehrotra and Kapur (1974) presented research suggesting that the rate of flotation was strongly correlated to the aeration rate. McKee et al. (1976) continued to demonstrate the importance of airflow-rate linking it to the entrainment rate of hydrophilic gangue material."

Jan 1, 2006

By Harold E. Goetzman, Blair R. Benner

The U.S. iron ore industry is located primarily in Northern Minnesota and Michigan's Upper Peninsula with one additional small plant in Missouri. There are currently some 10 plants operating that produce about 48 million tons per year of pellets. The major reagent use occurs in the three general areas of: flocculation, flotation and pellet additives. Minor areas of usage are for corrosion inhibition and dust suppression. Current practice as to types of reagents, consumption, and method of application are reviewed. The interaction of reagents with other parts of the process are discussed. Also included is a discussion of future reagent needs.

Jan 1, 1994

By Robert E. Brown

Magnesium recycling has been used to recover both new scrap and old scrap. It was used extensively in Germany during WWII to expand the magnesium supply. There were a large number of magnesium recyclers in the US who got their start smelting old scrap, old airplanes and old waste dumps from the WWII build up. As the world magnesium industry dwindled, only a few companies were left that did magnesium recycling as a primary business. The sand foundries tended to recycle of their production scrap in their melting furnaces. Even the original die casters tended to put scrap directly back into melting furnaces at the die casting machines. As high purity alloys were developed and the use of die castings in automotive work increased, the tendency was to let the magnesium recyclers convert the scrap back to high quality ingot. Automotive use has grown because of the low density of magnesium. This property is the one of the biggest problems to overcome in shipping scrap. Gates and runners from die casting are very irregular shapes and it is very hard to load a truck with enough material to get a low shipping cost per pound. Recent new equipment companies have developed magnesium equipment that is specifically designed to recycle, refine and cast secondary magnesium metal. These melt cells are supplied as integrated units to magnesium casting sites. The cost and effectiveness of this approach will be discussed.

Jan 1, 2000

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By G. L. Oldright, John D. Sullivan

"The present article is the second of a series of papers dealing with the dissolution of copper minerals in various reagents. Work done on the problem has been carried out at the Southwest Experiment Station of the United States Bureau of Mines, in cooperation with the Department of Mining and Metallurgy, University of Arizona. The first paper4 dealt with the dissolution of azurite, malachite, chrysocolla, and tenorite. Preceding articles5 have also dealt with other factors involved in the leaching of copper ores.Cuprite (Cu20) is usually considered as a mineral which is not adaptable to sulphuric acid leaching. Hofman,6 in describing leaching by sulphuric acid, states: ""Cuprite is decomposed into CuO and Cu; and ore carrying cuprite has to be oxidized (weathering, roasting) before treatment."" Greenawalt7 says: ""When acted upon by dilute sulphuric acid, it is partly reduced to metallic copper and partly oxidized into copper sulphate. When heated with strong acid it is entirely oxidized to sulphate."" Work to be described in this article was undertaken to ascertain the conditions whereby all the copper in cuprite could be converted into the soluble sulphate."

Dec 1, 1929

By Peter J. Borchardt, Helen M. K. Andersson, Donald A. Bruce

Grouting is a useful engineering tool for tunnels throughout the world. A wide variety of methods and materials are used, reflecting the broad range of geological, hydrogeological, and structural demands. Most tunnel grouting is conducted with cement, which produces acceptable results in appropriate conditions. However, there are cases where such grouts are not practical, but polyurethane grouts can be extremely useful. Regretfully, these grouts are frequently poorly understood, leading to improper application and therefore poor results. This paper provides a fundamental overview of their application, both used individually and in combination with cement. Case histories from Scandinavian practice are cited.

Jan 1, 2001

By Roger S. Dewey

1.1. INTRODUCTION Despite indications of a general economic recovery in the U.S. during the mid-19801s, mine operators have not generally shared in the benefits of these reported better times. Budgets have not rebounded, borrowing is tougher, parent companies' pockets are not as deep as in previous years, and margins are not any better -- if there is any left over at all. Managing capital equipment budgets is always a challenge, and the last five years of stretched equipment lives make these decisions more tenuous. Delays and avoidance of replacements due to tough times inevitably makes those decisions increasingly difficult and usually more expensive The purposes of this paper are to present. a brief refresher outline of the fundamentals of equipment replacement analysis, to suggest a number of papers where analysis methods are explained in greater detail. and to recommend the use of a widespread microcomputer software capability (1-2-3) as the easiest path to a much-needed solution for a very difficult, and usually under-supported management decision problem 2. REPLACEMENT DECISION POLICY Investments in equipment replacements must compete for capital with all other investment alternatives. Capital for replacements of ten represents a greater commitment than do the new projects which a company might handle in a given year. But. sadly, formal policies for standardized analysis of replacements rarely exist, even in major companies. Yet this policy can be very significant in determining the competitiveness of a firm. Whereas many replacement decisions are based on cost minimization, economists and financial analysts agree that wealth maximization or return on investment is the superior criterion. Though the difference may seem slight, agreement on a firm's financial objective is vital. Replacement policy should be straight- forward. have a logical basis, and a proper level of sophistication. There are several reasons to develop a policy for replacement decision-making: [I] 1 - equipment's optimal economic life is nearly always shorter than its physical life; 2 - mine life often exceeds equipment life, so management must face these decisions routinly 3 - replacement capital costs, on an undiscounted basis, can run 25 to 75% of original capital 4 - technological changes may result in a newer machine or system which can operate more efficiently, more safely. or less expensively 5 - estimates should be made consistently in the fundamental areas of life expectancy, availability, utilization. price escalation, taxes 6 - long-term and short-term budgeting without decent data and analytical capability is nearly impossible, or at least ineffective Policy development assumptions which must be considered include: the planning horizon, cost patterns, interest rates, availability of capital, replacement vs. expansion, technology advances.

Jan 1, 1987

By Travis Q. Lyday

Ecuador's economy continued to slow in 1982 due, in part, to declining foreign demand for oil, depressed world oil prices, and high international interest rates. Real growth of the gross domestic product (GDP) was estimated to be in the 2% to 3% range, down from the revised 4.3% recorded in 1981 and the 4.5% anticipated officially. In current prices, the GDP in 1982 was estimated at $12.1 billion.2 Inflation abated slightly from that of 1981 to an estimated 13.9% annual rate. The sucre was devalued in May by 32%, the first time in more than a decade, as a result of the pervasive flow of capital abroad. Ecuador's production of petroleum increased an estimated 1.9% in 1982 compared with that of 1981. The consortium of Corporación Estatal Petrolera Ecuatoriana (CEPE), the state oil company holding a 62.5% interest, and Texaco Inc. (37.5%) produced an estimated 98%, or approximately 211,000 barrels per day, of the total from the northern part of El Oriente, the eastern jungle region, where a Texaco-Gulf Oil Corp. partnership discovered oil in 1967. Gulf subsequently sold out to CEPE in 1977 for $117 million, Remaining production was from the Santa Elena Peninsula Fields on the Pacific coast where production has been steadily declining for several years.

Jan 1, 1984

By Mauricio Olivares

About Largest combined Phosphate and Potash company in the world Corporate headquarters in Plymouth, Minnesota Publicly traded on NYSE under MOS

Aug 1, 2013

By Thomas M. Barczak, Claude A. Goode

Principal criteria in the design and operation of longwall mining systems are examined. The decision to apply longwall mining is investigated from an economic viewpoint, and the impact of economics on system design are addressed. Geological considerations and requirements for effective long- wall mining are provided. Ground control factors determining panel design are outlined, as well as environmental considerations. Operational practices are discussed and alternatives recommended. The impact of face moves and the potential for mining wider webs are assessed. Constraints to production are identified and the potential for increasing production of longwall systems is established.

Jan 1, 1982

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Chang Wei, Fan Zhang, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Marmatite is an important resource of zinc, which exist in forms of high iron and high indium. In order to recycle the valuable metal from these ores, the testwork of simultaneous leaching on neutral residue mixed with zinc concentrate of high iron and high indium has been conducted. The primary objectives are to leach the zinc and indium remaining in the neutral leach residue as ferrite using acid, and to reduce the ferric iron in solution to the ferrous by zinc concentrate, thereby extracting the zinc and indium in the zinc concentrate. The results indicated that in the following conditions, mass ratio of neutral residue to zinc concentrate of 1:0.25, particle size of 74-58 μm, initial sulfuric acid concentration of 150 g/L, liquid to solid ratio of 8 L/kg, temperature of 90°C, reaction time of 4h, the leaching efficiency of zinc and indium were over 95%, nearly 90% Fe was Ferrous in the leaching solution. This process effectively extracted zinc and indium and converted Fe3+ into Fe2+ in solution, and simplified the traditional process of reduction after leaching.

Jan 1, 2016

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By William H. Shockley

[Secretary's Note.—The following notes, arranged and edited in this office, but not yet revised by the author, were placed at my disposal with much modest hesitation (due to their incomplete and fragmentary character), upon my earnest request, and my argument that such recent and trustworthy data concerning a new and important mining industry ought not to be withheld from our Transactions, simply because they are not sufficient to constitute a complete academic treatise on the subject. This argument is recommended to the attention of many other members, who are waiting for the opportunity to contribute something "monumental" to our Transaclions. In a number of instances, death has nullified this ambition, and the intended "monumental " contribution has turned out to be an obituary notice by the Secretary, instead of a valuable record of the professional experieuce thus hopelessly lost to the world.—R. W. H.] The official publications of the Russian Government give fairly complete statistics of the dredges operated in the Empire; and in a recent English bluebook, Mr. Cook's report on Siberian Trade presents a brief account of dredging in Siberia. The data in Table I. (not given by Mr. Cook) have been taken from the Gold Mining Messenger (Russian) for July, 1905. These interesting statistics, though incomplete, show that the Yenisei dredges are working on poor ground and yield small returns. According to report, but few yield a profit exceeding 10 per cent. per annum on the capital invested. In the summers of 1904 and 1905, I traveled in the Urals as far north as lat. 61° N., long. 61" E., on the Losva river, a part of the vast system of the Ob river. This clear-water stream starts from the summits of the Urals at an altitude of 4,000 ft., and flows through a flat country, densely wooded with larch, spruce, pine, fir, birch and poplar. The river is full offish, and is navigable for good-sized steamers as far as Ivdell. Winter lasts from early November to late April, the temperature ranging from -60" F. to a summer maximum of 90° F. The rainfall is 20 in. The climate is healthy, although mosquitoes,

Jan 1, 1907

By D. C. Austin, P. J. Hazell, A. A. H. Ameri, J. P. Escobedo-Diaz, D. East, M. A. Bevan, A. D. Brown

Additive Manufacturing (AM) has become increasingly popular due to the ability to produce components with complex geometries and properties. The efficiency of this manufacturing method is investigated in this paper by examining the mechanical performance of AM austenitic stainless steel 316L under different strain rates. Dynamic compression experiments were conducted by using a Split Hopkinson Pressure Bar (SHPB). Microstructural observations were performed by utilizing optical microscopy. The behavior of this material is compared against stainless steel 316L manufactured by conventional methods. The results show that theAM316L used in this study display a considerable difference in the mechanical properties compared with conventional stainless steel alloys.

Mar 1, 2017