Search Documents

By Robert S. Hedin, David M. Hyman

Acid mine drainage (AMD) is a common water pollution problem on active and abandoned coal mine sites in the eastern United States. AMD forms when surface mining brings unweathered pyrite-containing rocks to the surface or when deep mining allows oxygen to contact buried pyritic strata. In the absence of neutralizing compounds, the drainage that results can be extremely acidic and contaminated with dissolved iron, manganese, and sulfate. Drainages with pH < 3.0 and concentrations of sulfate greater than 1,000 mg/L, iron greater than 50 mg/L, and manganese greater than 10 mg/L are common. Where water flows through alkaline materials (such as limestone) before surfacing, the drainage is less acidic and occasionally circumneutral, but it can still contain high concentrations of sulfate and metals. Current water quality standards in the United States require that mine discharges have a pH between 6 and 9, total iron concentration less than 3.0 mg/L, and manganese less than 2.0 mg/L. At thousands of active and inactive mine sites, drainage does not meet these standards and is being treated before discharge by the mining company. At thousands of other sites, which were abandoned prior to the enactment of water pollution laws or were operated by companies that have gone bankrupt, untreated AMD is polluting receiving water systems. The standard mine drainage treatment system involves the addition of a1 kal ine chemicals to the water, which raises the pH and cause metals to precipitate in a settling pond. These systems are expensive, often costing tens or hundreds of thousands of dollars per year for chemicals, operation, maintenance, and disposal of the metal- laden sludge. Because the drainage on many sites will likely be contaminated for decades, there is financial incentive to find alternative water treatment systems. In the last five years, many mining companies and engineering firms have experimented with the construction of wetland treatment systems. Very few of the several hundred wetland systems that have been built are performing well enough to justify total abandonment of chemical treatment. Nonetheless, systems continue to be built because the mining companies have found that wetlands can reduce their AMD treatment costs. It is also their hope that further research and development will eventually result in systems that will completely rep1 ace chemical treatment and offer long term performance at minimal cost. The Bureau of Mines has been actively involved, from a research perspective, with this approach to AMD treatment since its inception. In this paper, the status of constructed wetland technology is discussed with respect to the construction and performance of systems, chemical and biological processes that affect AMD chemistry within constructed wetlands, and the future of this technology as perceived by the Bureau of Mines. ORIGINAL OBSERVATIONS The constructed wetland concept has its roots in observations of natural Sphaqnum peat wetlands that received acid mine drainage and, instead of being adversely affected, appeared to cause an amelioration of the polluted water (Huntsman et al. 1978; Wieder and Lang 1982). These observations instigated the idea that wet1 and systems might be used for the intentional treatment of mine drainage. Because the discharge of AMD into a natural wetland is prohibited in the U.S. by several laws, it has been necessary to construct wetlands which act solely as water treatment systems. Initially, most wetland research and construction efforts mimicked the original observations by utilizing Sphaqnum moss and peat. Despite promising laboratory results (Kleinmann et al. 1983; Tarleton et al. 1984; Burris et al. 1984; Gerber et al. 1985), virtually all field tests of Sphasnum-dominated constructed wetlands failed to provide sufficient water treatment for more than several months. Sphasnum proved quite sensitive to the stresses associated with transplanting, abrupt changes in water chemistry, excessive or insufficient water depth, and

Jan 1, 1989

By J. J. Bodmer

Although the similarity between puzzolana, or trass, and blastfurnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

By J. J. Bodmer

ALTHOUGH the similarity between puzzolana, or trass, and blast-furnace slag, as seen by comparison of the analyses, is a well-known fact, blast-furnace slag has not been used commercially as a substitute for those cementing materials. The reason, the writer apprehends, lies in the fact that unless such slag is disintegrated or subdivided by rolls, the process must either be too costly, or the material is not in a fit and proper condition for the purpose. In order to produce a reliable slag cement, the slag must be ground together with the lime into an impalpable powder. The subdivided slag must, therefore, be perfectly dry, and, at the same time, friable. The stronger the hydraulic properties of the lime, the more reliable the slag cement will be, and practice has proved, that the slag from a gray-iron furnace gives the best results. The slag cement which has given the results shown in the annexed table, under pressure tests, was composed of six parts of slag, from a blast-furnace producing No. 3 foundry iron, and one part of lime, of medium hydraulic properties. The above-described class of cement bears storing as long as most Portland cements, and the cheapness of its production is self-evident.

Jan 1, 1874

By Sergey Ulianov, Arkady Senchenko, Alexey Shvets, Arkady Bakotin

"This paper is devoted to ultrafine grinding of processing products. This process allows one to include into operation complex ores which earlier were considered as inefficient and economically inadvisable to treat. Fine dissemination of valuable component often does not allow its liberation via standard grinding in ball mills, and therefore requires modern methods of ultrafine grinding (UFG). An example of successful ultrafine grinding usage is its application for crude flotation concentrates regrinding before cleaner flotation stages. A problem often arises with a commercial copper concentrate production in the course of copper ore flotation. Crude flotation concentrate regrinding in a ball mill does not provide for good liberation of the material before cleaner stages. UFG application allows one to get commercial copper concentrate with copper grade of 20% and higher. Another example of ultrafine grinding application is its usage for highly refractory pyrite product received after gold-lead scavenger flotation of polymetallic ore. Earlier this product treatment was economically inefficient. At current application of ultrafine grinding down to 85% minus 20 µm and subsequent gravity processing it is possible to pass major part of gold (73.4%) into concentrate. The constraining factor for UFG application in processing may be the chemical activation of minerals. In the result of this, flotation selectivity may decrease. Therefore ultrafine grinding application extends the areas of efficient usage of metallurgical processes. New technologies allow increasing the level of valuable metals recovery."

Jan 1, 2014

By A. House

Newmont Mining Corporation owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006. Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix needed a process option to treat lowgrade transition and oxide copper ores. This meant that potentially revenue generating ore was being mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a run-of-mine (ROM) heap leach pad and solvent extraction/electrowinning plant (L-SX/EW). This paper will discuss the synergies and challenges of developing a copper L-SX/EW plant at the Phoenix copper-gold mill.

Jan 1, 2010

By H. Shimoda, K. Tamaki, K. Iizasa, M. Watanabe, K. Okamura

Modern Kuroko-type deposits occur in submarine calderas of island-arc fronts and back-arc rifts in Japan. They occur primarily on or adjacent to caldera boundary faults. Hydrothermal sulfides in the Myojinsho submarine caldera are one of Kuroko-type deposits, but their occurrence is different from other deposits found within the area 200 km2 around the Quaternary volcanic front of Izu-Ogasawara arc.

Aug 24, 2006

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

Jan 1, 1923

By H Plewes, A Bur, L Murray, J Pottie

Water recovery from tailings for reuse in mineral processing is essential to operation of mines in the Atacama Desert of Chile. With annual rainfall of 5 mm, the prudent and efficient use of available water resources is a major issue for the Escondida Mine and other mines in the area. The Escondida Mine is located at an altitude of 3100 m, in a very arid, seismically active part of the Atacama Desert of northern Chile. The site is located about 170 km from the coastal city of Antofagasta. From 1994 to 2002, tailings were discharged into the Hamburgo Tailings Facility, which comprises a series of æpaddiesÆ located near the open pit and mill. Because water in the region is only obtainable from groundwater sources, the paddy system incorporated a number of design features with the aim to maximise water recovery from the tailings. As part of the recent mill expansion to 237 500 metric tonnes per day, a new tailings facility, the Laguna Seca Tailings Facility, projected to be one of the largest tailings facilities in the world, was commissioned in 2002. Extensive studies were conducted for the design of the new facility to predict water recovery from the conventional wet disposal of tailings. The predictions were calibrated against the performance of the Hamburgo Tailings Facility and subsequently re-calibrated against actual performance during the first year of operation at the Laguna Seca Tailings Facility. Initial operation of the Laguna Seca Facility was marked by a coincidental change in tailings characteristics from design, which highlighted the need for thoroughly understanding tailings behaviour during deposition, and the parameters and deposition techniques that could enhance water recovery. Systems have been put in place to manage the tailings deposition and respond to changes in key parameters such that water recovery targets can be reliably achieved. This paper describes the background studies that were conducted to evaluate evaporation and tailings behaviour, summarises the water balance and then presents some observations from the commissioning and start-up of the facility.

Jan 1, 2003

By P. Piga, O. Sammarco

There is a markedly increasing tendency to design deeper and deeper mines, to use larger amounts of explosive per round, to increase the advance rate of the excavations and so the natural ventilation tends to be more intense in the new mines. For this reason, the mines that make use of powerful mechanical ventilation should also take into account such factors as natural ventilation pressures, especially in the case of mines excavated in high-temperature rocks for which natural ventilation is particularly intense. The results of the studies reported here refer to a very hot mine excavated in an area with a high geothermal flow (the Boccheggiano - Campiano mine, southern Tuscany). At various external temperatures, experimental measurements and analyses have been made of the trend of the thermodynamic characteristics of the ventilation air and of the trends of the air/rock heat exchange along the downcast shaft and along the upcast shaft. These data were then used to work out approximate values of the corresponding natural ventilation pressures. After having identified the most conspicuous variations of the thermodynamic parameters of the ventilation air and the factors causing them, an assessment was made of the repercussions they have on the air flow rates and, above all, on the climatic conditions of the underground excavation sites. The natural ventilation pressures were found not to be constant in time; indeed they change continously and it is difficult to predict the changes. Moreover, it was found that their influence on the ventilation of a section of the mine network is greater if the effect of mechanical ventilation on that section is weaker. In the mine section where the measurements were carried out, some portions were found where the ventilation could become insufficient as a result of the effects of natural ventilation pressures. Finally, some guidelines to be followed in designing hot mines have been put forward which ensure efficient ventilation throughout the network at times with the aid of the natural ventilation pressures, which in certain circumstances may reach very high values in mines of this type.

Jan 1, 1987

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By D Thomas, B Gallagher

Valuable data for geotechnical interpretation and integration into effective Australian underground mine planning may often be available, yet is not always fully appreciated or utilised, particularly in the early stages of mine planning or in due diligence studies. There may be considerable benefits associated with early prioritisation of geotechnical evaluation and impact on mine planning. Unidentified, misinterpreted, or ill-defined adverse geological and related geotechnical resource characteristics can pose significant business risk to underground coal projects and operations. Preliminary resource definition in the early conceptual mine planning stages attributes significant focus (entirely warranted) on resource quality and structural geology constraints. Yet detailed geotechnical data analysis and interpretation, which may have a substantial down stream impact and sensitivity with respect to future mine planning strategies, at times is given lower priority, or scoped and resourced in the later stages of a bankable feasibility study. Through extensive mine planning experience and observation of downstream process impacts, it has been found there is often data available for geotechnical analysis that does not readily stand out or is not adequately understood or utilised, available at the early (conceptual) stages of mine planning. Part of the issue may be that exploration geologists are not necessarily experienced geotechnical engineers and do not necessarily recognise or understand all important parameters. Subject to appropriate application of experienced professionals data can be manipulated to provide key geotechnical hazard assessment at minimal cost, and provide a framework for understanding and optimising the mine planning process. Although there is no single prescribed strategy for resource evaluation from a geotechnical perspective, potential business risks and mitigation approaches can and should be adopted at the conceptual mine planning stage. There has been a recent focus in the metals industry to provide a reporting framework for geotechnical classification of mining projects. This paper outlines the strategies and gives examples of key analyses adopted in mine planning and discusses the relative merits of adopting a reporting framework as a tool for geotechnical classification in mine planning.

Jan 1, 2005

Jan 1, 1923

By R. Dekkers, J. Plessers

The feasibility of using hydrogen to obtain clean steels is investigated. High hydrogen contents are generally considered as detrimental due to the risk of flakes, bubbles and breakouts during casting. Hydrogen can nonetheless be removed by degassing of the steel. The results of industrial campaigns, where total oxygen content and hydrogen content were monitored, are presented. High resolution microscopy of inclusions and laboratory experiments on the rate of inclusion removal by CaO-Al2O3 slags at different partial hydrogen have been carried out. So far, evidence that hydrogen may influence inclusions or the steel cleanliness is not clear. Keywords: hydrogen, cleanliness, inclusions.

Jan 1, 2004

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By Mario Samamé Boggio

La ausencia de la enseñanza adecuada en el comportamiento mecánico de materiales y la falta de análisis en los cursos de ingeniería, señalan un problema de neutralidad e integración del concepto de ingenierías en la educación universitaria. En ese sentido, el presente texto describe la importancia de la enseñanza con la realidad del ingeniero, las implicancias de sus especialidades y su rol político como ciudadado que conoce para mejorar la vida humana en el universo.

Mar 1, 1979

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By W. C. Maurer

Although millions of feet of rock are drilled annually, the basic drilling mechanisms involved are not well understood. The primary reason for this lack of knowledge is because the basic principles of rock failure are not well understood and rock failure is the primary mechanism in drilling. A better understanding of the drilling mechanisms would enable a more scientific approach to the design and use of drills and bits. The paper reviews several models which have been proposed to explain various aspects of the different drilling methods. These models are described and their limitations and areas of application are discussed. Drilling rate relationships are developed and related to the basic rock failure mechanisms. TYPES OF MECHANICAL DRILLS There are three basic methods of mechanically attacking rock: 1) percussive action, 2) rotary action, and 3) combined rotary-percussive action. A percussion drill applies a force perpendicular to the rock surface and the bit moves into the rock perpendicular to the surface, forming a crater beneath it (Fig. 1). A rotary drill applies a constant thrust to the bit while a torsional force moves the bit parallel to the rock surface, breaking the rock ahead of it. A rotary-percussive drill applies both a rotary force and a percussive force to the bit which moves into the rock at an angle to the surface. The commonly used drills can be classified as: rotary-drag, diamond; percussive-hammer, piston, churn; and combination-rotary-percussive, roller.

Jan 1, 1967

By R. V. Ramani, A. S. C. Owili-eger

The quantity of methane emitted into the mine atmosphere and the movement of gas through solid coal and the adjoining country rock are dependent on the physical properties of the medium, boundary con¬ditions, the initial gas pressure distribution, and the combination of natural and mining factors. Functional relationships between these factors are not yet known. Consequently, the development of rigorous mathematical models to predict methane flow into the mine air is difficult and to date no model has been reported which is capable of such a function. Thus far, empirical formulas available for the calculation of gas quantity released from underground sources require too much his¬torical data, not currently available. Again, these estimations are at best only crudely approximate. The numerical methods available have not been made practical enough for industry wide application. Therefore, the development of a relationship amenable to numerical analysis and practical enough for use in the industry would provide the flexibility lacking in analytical approaches. The mathematical models given in equations (7) and (8) are further attempts in presenting practical models for predicting the quantity of methane emission into the mine environment. Equation (7) is the steady state model and equation (8) is the unsteady state model.

Jan 1, 1974

A virtual reality approach is presented that can aid entities such as mining companies and land use planners in communicating a visual understanding of a mining operation to interested stakeholders, citizens? groups, and public committees. These visualizations are particularly useful in permitting, production planning and mining closures, contributing to accurate communication and evaluation of mine plans, ultimate land use and evaluation of potential design options A case study is presented, that was created using commercially available virtual reality tools, to emphasize the benefits of visualization technologies in the sustainable development of mineral resources.

Jan 1, 2003