Search Documents

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By J. A. Herbst

Successful transitions from micro- to macro-engineering are the keys to effective technology transfer between research and development organizations and industrial end users. At the same time, it has proven to be one of the most difficult tasks that the minerals industry has had to manage. Typically, developers of fundamental information concerning how mineral processing subsystems work have been academics and government scientists. These are the individuals giving the most important input to micro-engineering models that can benefit industrial operations. Publication is the usual route for "attempting" to transfer this technology to the end users. Unfortunately, with such publications, very little direct communication occurs concerning real industry needs or the future steps required to make the particular micro-engineering model useful. In the past, the industry has relied on in-house R&D groups and plant metallurgists to "translate" publications, to provide useful macro-engineering tools for plant applications. To some extent, engineering companies have also been asked to serve this function. However, these firms have been rather ineffective in this area since their conservative nature has caused them to look rather suspiciously at new technology. This approach to technology transfer has worked, albeit clumsily, for the last several decades. This communication system is now on the verge of total collapse due to conditions of the minerals industry. Mining companies can no longer afford the significant overhead expenses of specialized technical staffs. Universities are finding it extremely difficult to interest US students in mineral engineering programs, and funding for such programs is weak. Faculty members involved in micro-engineering research today tend to focus on pure (non-application-oriented) research.

Jan 1, 1992

By N. E. K. Schuttler

Experience with Mars pumping of underground water by N. E. K. SCHUTTLER (Visitor) As the result of a planned increase in production, Vaal Reefs Exploration & Mining Company Limited increased the hoisting capacity of their existing equipment to its fullest extent and installed Mars pumps and a washing plant. The layout of the installation is described, and details are given of the modifications made to overcome its weaknesses. Plans to change the present four-stage system to a seven-stage system are outlined.

Jan 3, 1977

By H. B. Comstock

This paper reviews the trends in supply and consumption of the principal magnesium compounds in the United States in relation to domestic requirements and world resources. The data are confined to these principal magnesium compounds: Magnesium chloride, magnesium hydroxide, precipitated magnesium carbonate, and magnesium oxide (commonly referred to as magnesia). The properties and uses of magnesium compounds are shown in various chapters of' the 2nd edition of Industrial Minerals end Rocks. 3/ The third edition of this reference is in preparation. A more recent description of properties, uses and sources of magnesium compounds appears in a Bureau of Mines publication.4/ The American Iron and Steel Institute and the Refractories Institute have published comprehensive data on the properties and uses of basic refractories. Many magnesium compounds are prepared by the producers to meet specifications set by individual consumers.

Jan 1, 1960

By J. C. Edwards, C. C. Hwang

In ventilated tunnel fires, smoke and hot combustion products may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of this reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels and building corridors. In the present study, conducted by the National Institute for Occupational Safety and Health, a CFD program (fire dynamics simulator) based on large eddy simulations (LES) is used to model floor-level fires in a ventilated tunnel. Specifically, the critical ventilation velocity that is just sufficient to prevent the formation of a reverse stratified layer is simulated for two tunnels of different size. The computer code is verified by checking the computed velocity profile against experimental measurements. The CFD results show the leveling-off of the critical ventilation velocity as the heat release rate surpasses a certain value. At this critical ventilation, the ceiling temperature above the fire reaches a maximum for both tunnels. The velocity leveling-off can be explained from this observation. An extended correlation of Newman (Combust. Flame 57 (1984) 33) is applied to the temperature profiles obtained by CFD. At the critical ventilation, temperature stratification exists downstream from the fire. The computed critical ventilation velocity shows fair agreement with available experimental data taken from both horizontal and inclined fire tunnels. The CFD simulations indicate that the Froude modeling is an approximation for tunnel fires. The Froude-scaling law does not apply to two geometrically similar fire tunnels. The CFD results are compared with two simple theories of critical ventilation by Kennedy et al. (ASHRAE Trans. Res. 102(2) (1996) 40) and Kunsch

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

By N. F. LeJeune

For a number of years the Bureau of mines has conducted semi-annual surveys to determine the changes in the characteristics of the motor gasoline being sold in the United States. The Bureau of Mines surveys, from April, 1917, to January, 1943, indicated a progressive decrease in the end point range. The survey for July, 1923 showed an interruption in this progressive decrease. This interruption, as shown in Table 1, in the line marked "Difference," was apparently a definite one, for the data obtained in the surveys of July, 19233, January, 19244, and the present one, apparently substantiate it. The figures in Table 1 were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points and the 10 per cent having the lowest end points were grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10 per cent" and the ?Maximum 10 per cent," respectively. The same scheme was used on the succeeding surveys.

Jan 1, 1924

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By Adderly Reeves, Renzo Dávila, Cinthya Lozano

Anglo American Quellaveco S.A. inició sus actividades productivas en el año 2022 con un Centro Integrado de Operaciones (IOC) que centraliza el monitoreo y control de todas las actividades productivas de la cadena de valor y articula decisiones ágiles basadas en datos. A través de la gestión operativa del IOC se contribuye significativamente al cumplimiento del programa semanal de producción, empleando aplicaciones tecnológicas avanzadas y dentro un marco de filosofía de operación integrada que no sólo integra físicamente el control de las estaciones de trabajo para cada una de las operaciones unitarias de la cadena de valor, sino que también está habilitada para trabajar con una filosofía de operación integrada.

Sep 29, 2023

By R. W. Jenkins

RACKLESS equipment is being used by the T Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used instead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone. It was known that the argillaceous cement rock was underlain by crystalline high calcium limestone. After an extensive drilling program it was found that there were large reserves of limestone underlying a recumbent syncline exposed in the south wall of the company's No. 3 cement rock quarry. A quarry was started on the vertical limb of this fold in 1927, and by 1930 the full requirement of the plant was met. After 1945 production diminished because of the occurrence of dolomite beds in the south wall. The quarry floor was then 135 ft below the cement rock level and 285 ft below surface. In 1949 Gerald I?.

Jan 1, 1955

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By Z. M. Beiranvand, M. Moghaddasi, A. Naeimi, Y. Naami, M. Raoufi

Titanium iron oxide and nickel-chromium coatings were applied on low-carbon steel substrates using the high-velocity oxygen fuel thermal spraying process. The microstructure, phase composition, and hardness of the coatings were analysed using scanning electron microscopy, x-ray diffraction, and microhardness tests. The phase analysis confirmed the formation of oxide compounds in the coatings. The average microhardness values for titanium iron oxide and titanium iron oxide-nickel-chromium coatings were measured at 580 HV and 970 HV, respectively, under a 100 g load. The corrosion resistance of the coatings was evaluated in a 3.5% sodium chloride solution using electrochemical impedance spectroscopy (EIS) and polarisation tests. The results indicated that the nickel-chromium composition exhibited superior corrosion resistance, which was attributed to its low porosity, preventing solution diffusion into the substrate. Wear behaviour was assessed using a pin-on-disk test with a tungsten carbide pin as the counterbody. The incorporation of nickel-chromium into the titanium iron oxide coating resulted in an 80% reduction in weight loss, indicating significant improvement in wear resistance. These findings suggest that nickel-chromium-modified titanium iron oxide coatings enhance both corrosion and wear resistance, making them promising candidates for industrial applications.

May 8, 2026

The 8th Annual University of Cape Town (UCT)/ University of Stelenbosch (US) Minerals Processing Symposium was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd August, 1990, under the auspices of the Western Cape Branch of The South African Institute of Mining and Metallurgy. The primary object of this meeting was to give research students at UCT and US the opportunity to present their work to a critical audience from industry, and to obtain feedback regarding the research needs of the minerals industry. Although the emphasis of these symposia is on work in progress at US and UCT, they also create an excellent opportunity for informal discussion between academics and metallurgists in industry. The first symposium in this series was held in 1982 at US, while the symposium in 1989 was replaced by the International Colloquium on Developments in Froth Flotation, also held in Gordon's Bay.

Jan 1, 1990

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019