Search Documents

By Yang Hai-long, FAN Gang, LI Cun-xiong, WEI Chang, LI Min-ting, LI Xing-bin, DENG Zhi-gan

Hydrothermal sulfidation of pure cerussite with elemental sulfur has been reported in the present paper. The variables considered in the study were temperature, time, particle size and elemental sulfur fraction in the reacting mixture. Temperature was the most important factor at temperatures above 180 , PbS and PbSO4 were the only stable reaction products in the sulfidation of cerussite. The experimental data indicated that under the hydrothermal conditions with a particle size of -74+58 μm and sulfur fraction in reacting mixture of 15% at 200 °C for 120 min, and 92% of lead sulfidation rate was achieved.

Jan 1, 2016

By T. Tsurata

The accumulation of thorium and/or uranium by various microorganisms from a solution containing thorium and/or uranium at pH 3.5 was examined. Among the species tested, a high accumulation ability for thorium was exhibited by strains of gram-positive bacteria, such as Bacillus megaterium, B. subtilis, Micrococcus luteus, Rhodococcus erythropolis, and actinomycetes, such as Streptomyces levoris. On the other hand, though uranium was accumulated in small amounts from the solution containing both elements by all these microorganisms, actinomycetes, such as S. flavoviridis and S. levoris had relatively high uranium accumulation abilities. In these high performance thorium- and uranium- accumulating microorganisms, S.levoris, which accumulated the largest amount of uranium from the solution containing only uranium at pH 3.5, could accumulate about 300 µmol thorium and 133 µmol uranium per gram dry wt. of microbial cells from a solution containing both thorium and uranium at pH 3.5. After this screening, uranium accumulation using microorganisms isolated from uranium mines, among which some strains of bacteria were found to possess an extremely high uranium accumulating ability. The microbial biomass may thus be considered for use as an accumulating agent for the removal and recovery of uranium that may be present in metallurgical effluents, mine tailings, seawater and other sources. Recently, hundreds of micro-organisms existing in uranium deposits located in North America, Australia, and Japan for their ability to accumulate large amounts of uranium, and found some new strains which accumulated large amounts of uranium, such as Lactobacillus and Bacillus sp. from Japanese and Arthrobacter and Bacillus sp. from the United States uranium deposits. These bacterial strains can accumulate about 2500 µmol uranium per gram dry wt. of microbial cells within one hour. These microbial cells can remove uranium from the uranium refining wastewater with a high efficiency. The accumulation of uranium from a solution (pH 5.8) by microorganisms contained Arthrobacter nicotianee, which is a similar strain mentioned above Arthrobacter sp., was examined. Among the 76 strains of 69 species tested (23 bacteria, 20 actinomycetes, 18 fungi, and 15 yeasts), high uranium accumulation ability was exhibited by strains of the bacteria, A. nicotianae, B. subtilis, and M. luteus. A. nicotianae cells, which showed the best performance, could accumulate about 698 mg uranium (2.58 mmol) per gram dry wt. of microbial cells.

Jan 1, 2014

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By Adriana Aurazo

Actualmente, el Perú cuenta con una minería del primer mundo, más sostenible en su desarrollo productivo y con mejores práctica en tecnología e innovación que contribuyen al cuidado del medio ambiente, así como respecto de su interrelación con los actores de su entorno y el Buen Gobierno Corporativo. Luego de analizar algunas consideraciones generales en materia de estándares medioambientales, sociales y de gobernanza (ESG, por sus siglas en inglés) para el sector minero, se destaca la importancia de la automatización de datos así como de plataformas de sistematización integrada que permiten realizar un seguimiento de las métricas ESG y la presentación de informes de sostenibilidad. Por ende, la inversión digital minera en dichas materias, será el foco en los próximos dos o tres años.

Sep 29, 2023

By AIME AIME

T HE Executive Board of the American Engineering Council held its fourth meeting at St. Louis on the first anniversary of the organizing conference which met in Washington on June 3,1920. Representatives of a number of the leading engineering organizations in the vicinity of St. Louis were present by invitation. The members of the Executive Board were guests of the Associated Engineering Societies of St. Louis. They were given a delightful ride about the city and were entertained at the Glen Echo Country Club at dinner. The special committee that had been appointed to draft resolutions to Mr. Hoover submitted the following, which were adopted : WHEREAS, our President, Herbert Hoover, has been appointed Secretary of Commerce in the Cabinet of the President of the United States, and WHEREAS, in consequence of his acceptance of this high public office, he has deemed it necessary to tender his resignation as President of The Federated American Engineering Societies.

Jan 1, 1921

By AIME AIME

CLYDE WILLIAMS, after graduating from the University of Utah as a chemical engineer, worked for a time in western mills and smelters. He then joined the U. S. Bureau of Mines and during the World War studied Ordnance Department and Navy problems on ferroalloys and alloy steels at the Cornell University laboratories. Later, as superintendent of the Northwest Experiment Station of the Bureau, he was active in electric furnace and ore reduction work. Clyde then went to South America and surveyed the iron and fuel resources of the Argentine. Returning, he became chief metallurgist of the Columbia Steel Corp., of

Jan 1, 1936

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By R. M. Winslow

"The phosphorus content of an iron ore is a determining factor as regards the value of the ore and also its metallurgical treatment. If some method of treatment, such as concentration, leaching, etc., could be used and the phosphorus con- tent of the ore reduced, it would be an important advancement in the iron mining industry towards the utilization of high phosphorus ores. Large bodies of material toe high in phosphorus to be marketable under present conditions would be made available, and a great deal of ore from the Cuyuna Range and other places, which is relatively high in phosphorus but otherwise suitable for making spiegel, could be reduced in phosphorus content sufficiently to permit its use in furnaces producing speigel.The form in which phosphorus occurs in iron ore is a much disputed question and it probably varies with the type and location of the ore. The statement has been made that ore piles on long exposure to the atmosphere often decrease in their phosphorus content. (Emmons, S.F. - Ore deposits, 1913, p. 652; Leith, C.K., Mesabi iron bearing district, U.S.G.S. Monograph 43, 1903, p. 275) There is described below experiments on the leaching of iron ores high in phosphorus, to determine whether it was economically possible to reduce the phosphorus content appreciably by leaching. As the research had a practical as well as a theoretical application, only low concentration of acids and alkalies were used.A number of variables were tried, among these being: (1) The solvent used, (2) strength of the solvent, (3) volume of solution used, (4) time ore was agitated (5) type of ore, and (6) screen size of the ore. The amount of ore taken was kept constant."

Jul 1, 1921

By Jr. Arcand

Canadian Economy ? Getting Results ???? A stronger Canadian economy ???? National debt cut ???? Taxes reduced, tax-free savings account, support for manufacturing sector ???? Assisting with infrastructure Aboriginal issues affect all Canadians ???? Aboriginal prosperity is in everyone?s interest ???? Conditions for Aboriginal success include: - Indian residential school settlement - resolving outstanding specific claims

May 1, 2008

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016

By C. E. MacQuigg

BY and large the education of the engineer has been conservative and the reasons for this are obvious. Quite properly it has been a tradition of engineering education that facts and not fancies must be adhered to. Without a doubt, those men who formed the mold of our engineering philosophy as much as it is possible for such molds to be established-rightly held the highest standards of intellectual honesty. Fortunately, it was unthinkable to them to temporize with untried theories and naturally the men whom they trained as engineering educators carry this philosophy in turn to their students, thus handing down the tradition of stability.

Jan 1, 1943

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

Founded in 1994 through a joint effort between Underwriters Laboratories Inc. (UL), the U.S. Consumer Product Safety Commission (CPSC) and the National Electrical Manufacturers Association (NEMA), the Electrical Safety Foundation International (ESFI) is North America?s only non-profit organization dedicated exclusively to promoting electrical safety in the home, school and workplace. ESFI is a 501(c)(3) organization funded by electrical manufacturers and distributors, independent testing laboratories, utilities, safety and consumer groups, and trade and labor associations. ESFI sponsors National Electrical Safety Month each May, and engages in public education campaigns and proactive media relations to help reduce property damage, personal injury and death due to electrical accidents. The Foundation does not engage in code or standard writing or lobbying and does not solicit individuals.

Jan 1, 2004

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor's analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By Renn Oler

Corrosion can often cause significant strength reduction and failure of steel rockbolts, thus demanding continuous rehabilitation and posing challenges to underground mines in maintaining long term ground support. The mining industry has traditionally applied galvanized and epoxy coatings for protection of ground support and reinforcement in corrosive environments due to cost considerations. However, under a harsh and corrosive groundwater condition with extreme pH levels, failure of the existing coated rockbolts often results in failure and falls of the mine roof, especially in long-term mine drifts or entries. To prevent the roof falls induced by corrosive bolt failure, DSI developed a new polymer coating, called ?Obduro AP coating,? to combat harsh and corrosive ground conditions. The new polymer coating was tested in extreme conditions to identify weaknesses and was found to be capable of handling highly corrosive mine water solutions. This paper highlights the challenges faced by underground mines with corrosive bolt failure and shows that the DSI Omega BoltTM can withstand the most corrosive ground conditions when it is coated in the new, economic Obduro AP coating.

Jan 1, 2014