Search Documents

By Tim McMahon

"A slurry is any combination of liquids and solids where solids make up more than 10 percent of the mixture. Mining operations create various types of slurries from processes such as dewatering, bitumen extraction in oil sands, concentrator plants, milling operations, tailings, lime addition and so on. The mines then transport these slurries through pipelines (Fig. 1).Slurry valves are used when the mine needs to transport ore a long distance and there are no other viable transportation methods, such as roads or railroads.Severe service valves must be used in slurry applications and they must be tested to ensure reliability. This article describes how Emerson designs and tests its Fisher valves for use in mining slurry applications.Slurry pipeline valvesWithin a slurry pipeline system, valves are required as part of the pumping stations, choking stations and isolation stations. There may be multiple pumping stations depending on the length of the pipeline or the terrain it crosses. Choking stations are used to reduce the velocity and the pressure in the pipeline, either before a pumping station or at the end of the pipeline, and to ensure the pipeline does not slack (remains full and pressurized). Isolation stations exist so that a pig (a device sent through a pipeline to clean or inspect the pipe) can be inserted or removed from the pipeline.Typical valves used in a slurry pipeline are severe service ball valves. The valves use floating balls that are held between the seats and are not pinned or permanently attached to the shaft that rotates the ball. The inside diameter of the ball typically matches the pipeline inside diameter, enabling the pipeline to be cleaned or inspected with a pig.They can be built to accommodate the high pressures required for the typical slurry pipeline. These pressures can require up to ASME Class 2500 valves and flanges. The valves can get qlarge, up to NPS 36 inches.Specialized segmented ball valves and slurry knife gate valves are also used in some slurry applications when pressures are lower, in the ASME Class 150-300 range."

Sep 1, 2019

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

Detailed petrographic analyses of coal seams from the Newcastle, Illawarra, and Lithgow Coal Measures were made for a number of localities for each of twelve seams. From these analyses characteristic standardprofiles were derived for each seam. Two broad types of profile were found; one in which vitrite-poor and vitrite-rich layers alternate, and another in which there is a steady decrease in vitrite from the base to the top of the seam. From comparison of the petrographic profiles it was concluded that the Great Northern Seam in the Northern Coalfield is a possible equivalent to the BulIi in the Southern; and likewise the Fassifern to the Balgowni...

Jan 1, 1967

The consideration of environmental constraints and issues is a fundamental component of all stages of planning, development, operation and decommissioning mining and quarrying projects. Provision needs to be made at all stages for the cost of environmental components since it is of fundamental importance that they be recognised as an integral component of any project. This paper presents an approach to environmental costing, suggested levels for budgeting, and the cost benefits.

Jan 1, 1990

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix.

Jan 11, 1951

By R. Hope, C. van Heerden

In any process or organization inefficiencies are costly. In times of abundance this reality often does not receive much attention. During such times the focus is rather on increasing capacity to increase production. However, there is a growing awareness in the world of tougher economic, social as well as environmental conditions, and enterprises find themselves facing greater demands for accountability towards shareholders, the environment and the public, as well as growing competition for market share and limited global resources. This reality is no different in ensuring a sustainable mineral sands operation. In order to achieve this, any operation needs to be stripped of all process as well as operational inefficiencies. In this context it has become essential for any Mineral Separation Plant (MSP) to have the necessary process monitoring and control systems in place to continually monitor and optimize the production of on-spec products and maximize operational efficiency and consistency. The MSP Grade Control Solution developed by Crusader Systems and running on top of the CSense platform contributes towards these goals by improving the consistent production of on-grade product. This allows the process to operate closer to the maximum allowable product grade constraint, which in turn maximizes production.

Jan 1, 2003

By P. Duwez, C. B. Jordan

The phenomenon of the change of volume of pressed powder compacts upon sintering is well known in the field of powder metallurgy. Depending upon the metal or metals involved and the pressure used in forming, a compact may, in the course of time of sintering at a given temperature, expand mono-tonically, contract monotonically, or first show a volume change of one sign followed by a change of the opposite sign. It is clearly desirable to have accurate knowledge of the magnitude and sign of the change in dimensions to be expected in any given case, both from the point of view of direct usefulness in the fabrication of parts by powder metallurgy, and from the longer range viewpoint of elucidating the fundamental mechanism of metallic sintering. The present study was therefore undertaken as a first step in acquiring systematic and reasonably quantitative knowledge of the change in density of metal powder compacts during sintering. For practical reasons, copper was selected as the material to be studied first, and its densification followed as a function of temperature and time of sintering in hydrogen and in vacuum. Experimental Procedure The copper powder used was that designated by the manufacturer (Metals Disintegrating Co., Elizabeth, N. J.) as MD-151. This powder was sifted through Tyler standard screens to separate the fraction having particle size range between 200 mesh and 325 mesh, and this fraction was used in all the subsequent work. Compacts weighing about 10 g were then pressed in a 1 in. diam round die, using a pressure of 20,000 psi throughout. Sintering was carried out in commercially built electric furnaces in which the resistance windings are so disposed as to produce a nearly uniform temperature along the axis of the furnace for a length of about 18 in. centrally located. In order to be able to sinter in a controlled atmosphere, a 2 in. stainless steel tubing was inserted in the furnace. Each end of the tube was cooled by a water jacket about 7 in. long, and closed with a rubber stopper. The hydrogen used for one series of specimens was purified as described in Ref. 1. For the other set, a pressure of about 0.5 mm Hg was maintained during sintering by a Welch Duo-Seal Pump. The specimens were heated on square trays made of stainless steel. In placing specimens in the trays, a thin even layer of powdered aluminum oxide was first sprinkled on the bottom of the tray. A copper guard disk about half the thickness of the specimen was then placed in the tray and covered with a second layer of alumina. The actual specimen was then set on the guard disk, and a final coat of alumina sprinkled over the specimen. This technique was evolved for sintering the specimens in such a way as to reduce the influence of unknown extraneous factors to a minimum. If the specimen is placed directly on the tray and sintered, it is found that the resulting shape is that of a frustum of a cone, rather than a section of a right circular cylinder, since friction with the tray prevents the bottom of the specimen from contracting at the same rate as the top. In the arrangement used in these experiments, the guard disk provided a support which shrank at the same rate as the specimen, and the alumina powder reduced to a minimum friction between guard disk and tray, and between specimen and guard disk. The procedure followed in sintering consisted of bringing the furnace to the required temperature, and then inserting the specimen into the central heated portion of the furnace tube in one of the two atmospheres used. At the end of the heating period, the specimen was cooled by bringing it into a portion of the furnace surrounded by a water jacket. These manipulations were carried out without opening the furnace, by means of rods which were attached to the trays and operated through a sliding seal in the rubber stopper. The progress of densification of the copper compacts was studied at 1300, 1400, 1500, 1600, 1700, and 1800°F. At each of these temperatures, a specimen was allowed to sinter for each of the following time intervals: M, 1, 2, 4, 8, 16, 32, and 64 hr. The thickness and diameter of each specimen were measured with micrometers before and after sintering, and each was weighed on an analytical balance after sintering. Results The techniques described in the preceding section were found to give satisfactory results. The specimens were not detectibly warped after sintering, and were usually of uniform diameter (that is, truly round) to within 0.001 in., a very few showing a variation in diameter of ±0.002 in. All specimens were found to have the same diameter

Jan 1, 1950

By Fred D. DeVaney

MINNESOTA taconites are extremely hard, and fine grinding is required to produce an acceptable concentrate. To reduce grinding costs, waste material is rejected by magnetic separators as soon as it is liberated. Cyclones are now used in all Minnesota taconite plants to close the grinding circuits. Erie Mining Co. installed its first grinding section at Aurora, Minn., in 1948-a 9 ½ x12-ft. mill and a fine grinding section consisting of a 10 ½ x12-ft ball mill in closed circuit with a duplex 60-in. spiral classifier. Concentrates from the magnetic cobbers treating the rod mill discharge passed directly into the classifier; the ball mill discharge was also treated in magnetic separators and the concentrate from these machines also went to the spiral classifier. Both concentrates passed through ac demagnetizing coils. It is axiomatic that for proper classification the material in suspension must be well dispersed, and it follows that magnetic concentrate must be almost completely depolarized if classification is to be successful.

Jan 8, 1957

By S. Narra, M. Nelles, I. Eickhoff, S. Teitge

"The aim of the research is to develop a holistic process flow for the recycling of glass fibres from glass reinforced plastics (GRP) and carbon fibres from carbon fibre reinforced plastics (CFRP), wherein the dissolution of the fibre epoxy resin matrix, separation of fibre fractions and their renewed material use is intended. In clear distinction to the previous research and development projects, the aim here is to recycle complex composite structures such as dismantled/disused wind turbine rotor blades and end-of-life composite wastes. In the course of the study, mechanical, hydrothermal and thermal processes and their combined procedures will be developed. As the fibre length is a decisive quality criterion in the recycling of composite materials, the further focus of the study will be the development of upstream and downstream material processing, in which the fibres are retained in their original form. The evaluation of the recycled fibres obtained is based on the elemental composition, measurement and morphological evaluation of individual filaments by scanning electron microscope (SEM), micro tensile tests on single fibres and their comparison to virgin fibres. The resulting process water is analysed by gas chromatography and mass spectroscopy (GC-MS) and a potential recirculation is determined. In cooperation with companies from the composite processing industry as well as recycling companies, a return of the recycled fibres to the known manufacturing process will be examined and an energetic and economic evaluation of the overall process will be carried out. Ambitious aim of the study is to achieve an actual recycling instead of the present downcycling or the energetic utilization. INTRODUCTION As global warming increases, so does the awareness of consumption and production of energy. To counteract the effects of global warming, renewable energy has been increasingly used during the last two decades, not only in Germany, but worldwide. Both, hydropower and wind energy, hereby play a fundamental role. After the end of their useful life of 20 to 30 years, the wind turbines (WTs) are being dismantled. Due to their foundations and tower segments, their recycling rate hereby exceeds 90% by mass. So far, the resulting rotor blade waste played a minor role accounting for only 2 - 3 weight-% of the total plant. Rotor blades of modern wind turbines are made of glass and carbon fibers, which are embedded in an epoxy or polyester resin matrix, balsa wood, PU or PET foams as fillers as well as various paints and coatings. These wastes currently end up in waste incineration or are sold to non-European countries."

Jan 1, 2018

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

By Shuji Owada, Keisuke Yasukawa

Electrostatic and/or high tension separation has been used for the separation of rare metal bearing minerals, foods, industrial wastes and so on. Since the separation is achieved by the difference mainly in surface conductivity of particles, the efficiency in humid circumstances is very low, and then, the applicability is considerably limited. We applied the following two-stage pretreatment technique to the separation process, which involves (1) adjustment of surface wettability by adsorbing surfactant on the particle surface and (2) control of the surface conductivity by spraying with electrolyte aqueous solution. The addition of this pretreatment technique has been found to have a great advantage over conventional methods. Separation efficiency is achieved even in humid circumstances and selectivity can also be obtained between insulator minerals. The selectivity is very similar to that of flotation in wet process. This separation technique will be applied not only to mineral processing but the processing of industrial waste such as electric and electronic waste materials.

Jan 1, 1995

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By Derek Harvey

"The paper briefly describes the development of the Eickhoff ESA60 roadcutter which is based on the old and well used principles of the shearer loader. It is intended to show that the machine offers a viable alternative to the normal methods used for driving roadways and also for coal production . References are made to installations currently operating in Europe with applications ranging from roadway drivage to pillar recovery. The paper also looks at possible applications in Canada.IntroductionThis paper is an attempt to show how the principles used in mechanical cutting, conveying and roof support are being applied to a development system capable of catering to a variety of situations and conditions. It is also intended to illustrate how the same system can be used as a total mining system for the mining of many minerals.In order to give some sort of time perspective to the age of the principles, reference can be made to an article in Coal Mining & Processing which states:- During World War II the Germans developed the "" panzer"" or armoured face conveyor.- After the war the English developed power cutters or trepanners that were mounted on the face conveyor, this then developed into the shearer.- The first shearer was produced by the Anderson Company in England in 1950 and shortly after that the Eickhoff Company started manufacturing shearers in German y.- The first hydraulic roof support was produced in 1954 by Gullick.This is a potted history of the three major components of the new system, i.e.:- Mechanical cutting element based on the shearer.- Transport element based on the panzer.- Optional roof support based on the hydraulic face supports.It can therefore be said that since the "" youngest"" of the elements was produced in 1954 the principles of the system in respect of the rapid change in mining equipment are in fact old.Of the three major components the most important is the cutting element since the major benefits of the system are to be obtained from this."

Jan 1, 1985

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By Caitlin Rogers

The environmental and economic sustainability of froth flotation is dependent on effective management, which in turn improves the performance of a concentrator. In economic terms this means improved recovery of valuable minerals, in environmental terms this means effective management of acid generating tailings. Three indicators were selected to measure the performance of an integrated flotation system. The system consists of two stages of flotation; valuable mineral flotation followed by environmental desulfurisation by froth flotation. The suitable indicators were selected based on their fulfilment of four attributes. An attribute is a desired aspect of an indicator. The four attributes were: comprehensive, relevant, sensitive and quantitative. Two environmental indicators and one economic indicator were selected. They represent revenue generation from valuable minerals and environmental cost of management. The suitability of the selected indicators was shown using illustrative scenarios.

Jan 1, 2014

The mineralogy of regolith material for which whole rock geochemistry has already been done can be used to better understand/rank the significance of geochemical anomalies. Case studies show that the secondary minerals of the regolith environment have quite different capacities to incorporate pathfinder and target elements, eg hematite appears to be a better host to Pb than goethite and Pb rich alunite-jarosite minerals are a better Ag host than mimetite. Thus correlations between elements in regolith material may be strongly affected by mineralogy. Understanding of the significance of a geochemical anomaly is frequently enhanced by knowledge of the weathering susceptibility of different minerals. For example, when a mineralogical sequence which does not correspond to the expected order is found (eg feldspar overlying weathered material without feldspars) it is possible that transported material is present in the profile. Such mineralogical information is particularly relevant as exploration continues into areas of thick regolith.

Jan 1, 1997