Search Documents

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By R. W. Seedsman

In 1984 and 1985, two 7.6m diameter TBM tunnels were driven from the Donkin-Morien peninsula in Nova Scotia to access the Harbour coal seam. The design of the ground support was based on identifying zones of rock failure through the application of the Hoek Brown failure criterion and the early use of finite element analyses. In 1992, the mining project was abandoned and the tunnels allowed to flood. Monitoring data from the tunnel was subsequently used as a case study in the development of the concepts of brittle rock behaviour. In 2007, the tunnels were pumped out as part of a feasibility study into the reintroduction of longwall mining into the coalfield. There is a good match between observations of the collapse zones in the roof and sides of the tunnel and a simple elastic analysis using brittle parameters, a spalling limit of 5, and a low independent shear modulus. The brittle analyses form the basis of the design for the resupport of the tunnels.

May 1, 2009

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By X. Wu, E. Topuz

Booster fans have been extensively used in underground mines throughout the world. In the United Kingdom, S. Africa, Germany, and other countries, many non-coal and coal mines employ booster fans. These fans help to reduce air leakage, to provide an improved flow distribution and to reduce the overall cost of mine ventilation. Although booster fans have not been used in coal mines in the United States, a recent survey indicated that many coal mines would install booster fans if they were allowed to do so. With the inclusion of coal mines, the use of booster fans in underground mines is expected to increase substantially in order to maintain air quality and quantity requirements. Several techniques are used, with varying degrees of success, in determination of booster fan locations in an underground ventilation network. These techniques include linear programming, critical-path crashing, CPM together with cutset operations, the out-of-kilter method, and simulation techniques. This paper provides a brief comparison of these techniques, and reports on ongoing research for an improved methodology for the determination of booster fan locations.

Jan 1, 1987

By Tony B. Szwilski

A short study has been made of the underground mining potential in the Plains region, the Province of Alberta, Canada. Particular reference is made to the possible application of longwall mining: Presently underground mining is limited to small scale room-and- pillar methods. The problems anticipated with large scale mining at shallow depths (30 m) are examined. Production factors based upon longwall retreat mining utilizing shield supports are also considered.

Jan 1, 1981

By T. Sterry Hunt

I HAVE in a previous communication called the attention of the Institute to the geognostical relations of the crystalline iron ores belonging to the Eozoic rocks of North America, at which time I noticed (1) those associated with the gneisses of the Laurentian series, (2) those of the crystalline schists of the Huronian, as seen in Northern Michigan and in many localities along the Appalachians ; (3) those of Southeastern Missouri associated with petrosilex porphyries and schistose rocks, and presumed to be nearly of the same age with those of the Huronian schists; and (4) the highly titaniferous ores of the Norian or Labradorian series from Essex County, N. Y., and from various parts of Canada. It may here be remarked that, although the presence of titanium is most marked in the Norian ores, this objectionable element is sometimes found in the schistose ores of the Huronian, and to a lesser extent in certain Laurentian magnetites. The ores of each of these geological divisions have their individual peculiarities, which serve to distinguish them to such a degree that the magnetites and specular ores of the Laurentian are as dissimilar to those of the Huronian as are the crystalline silicated rocks of the two series. As it happens that these mineralogical dissimilarities correspond to differences in composition and in adaptability to different processes of manufacture, which, in the present condition of the iron industry, are objects of special consideration to metallurgists, it will be seen that these geognostical distinctions become of great practical importance. During the past year I was desired by the Geological Commissioners of Pennsylvania to devote a few weeks to certain geological studies in the eastern part of the State, in the course of which I was enabled to make, with regard to its crystalline iron ores, some observations to which I desire to call the attention of the Institute. I may mention, in passing, that the great South Mountain belt, from the Schuylkill to the Delaware, is composed of Laurentian rocks, in which are found the characteristic ores of the series like those of the Highlands of New Jersey and New York, and of the Adiron-

Jan 1, 1876

By H. R. Aldrich

This paper presents some of the results obtained during the field season of 1919 while mapping, in detail, the stratigraphy of the Gogebic Range in Wisconsin. The detailed stratigraphic section for the range was first published, in 1919, by W. 0. Hotchkiss,1 State Gcologist of Wisconsin. The idea of the continuity of the definite succession thus established was the result of underground work in the productive part of the range in Michigan and Wisconsin, where most of the required data also were obtained. The bulk of the range in Wisconsin is heavily covered by drift; in fact, there is but one satisfactorily exposed section across the entire formation, few partial sections, and only scanty outcrops of any size. Evidently mapping of the detailed members of the formation could only be established at a few points; and if from these small areas the .unexposed portions were to be mapped by projection, the only apparent method for projection was straight-line interpolation modified or supported by data from the scanty outcrops and from test workings. It was found that by tracing a magnetic line, the position of which in the formation may be determined from test pits and outcrops, the projection of that member through the drift-covered areas can be accomplished. The magnetic line serves as a datum horizon within the formation to which reference may be made in correlating outcrops and ledge matter thrown from test workings. The foot wall is easily located also, and from the two datum horizons thus available and the known proportional thickness of the several members in the type sections, outcrops and artificially exposed ledges can be correlated by lithological characteristics. As a result, the tracing of magnetic lines became the basis of our work on the stratigraphy and we were able to carry the mapping of detailed members throughout the length of the range. It was found that the magnetic horizon at the base of the Tyler slate was most easily followed by the dip needle; that discontinuity caused by cross-faulting could be established; that folding along the strike could be detected in a repetition

Jan 1, 1922

This brief resume of events, transpiring in Mexico, culled from the daily New York newspapers, since the last Bulletin went to press, does not indicate any degree of improvement in the situation. MEXICAN MINISTER TO FRANCE RECOGNIZED A dispatch from Paris quotes Alberto J. Pani, Mexican Minister to France, as saying lie lead received notification that lie might present his credentials at the French Foreign Office on May 13. This notice came at the moment the Mexican press was announcing his departure for Spain because of inability to present his credentials. MORE REVOLUTIONARY TROUBLES SOUTH AND NORTH Revolutionary outbreaks hulked large in advices from Mexico City at the end of May, says the New York Tribune. General Eznesto Danny, a major, four other officers and forty men, composing a train guard on the Isthmus of Tehuantepec Railroad, were killed recently in an attack by rebels under Felix Diaz's command. The troubles in the south, coupled with the fact that Villa's activities in the north have necessitated sending troops to campaign against him, have reacted in the capital seriously, it is reported. Military guards hi Mexico City have been doubled and machine guns have been placed on the roofs of the National Palace and the Cathedral. STRIKE AND MARTIAL LAW IN MEXICO CITY Advices from Mexico City, according to the Evening Sun, said that virtually every school teacher in the city was out on strike and that recurrent rioting was being put clown by armed trucks manned by Federal soldiers. The strike of the school teachers was clue to the fact that they had not been paid for months, but the direct incitement is said to have been the contrast between their impoverished position and that of Carranza's generals, who are described as rolling in wealth, and who flaunted their opulence on the streets of Mexico, riding about in high powered automobiles with women bedecked with diamonds and other jewelry. The city is said to be virtually under martial law with no immediate prospect. of a subsidence of the bitter feeling against the military caste.

Jan 7, 1919

By T Wettainen, G Shekhar, M Stromsten, B Skawina

The aim of a transportation system in an underground mine is to move the rock masses from one location to another in the most preferable manner by minimising the long and short-term operational costs. A continuous improvement of material transportation systems used in mines generates a need for continuous investigation of the current and new underground transportation systems. In an underground mine, an orepass is a common system used to transfer the material to the lower levels. If this system loses the ability to transport or store the necessary material capacities, it would result in production disturbances. In this paper, discrete event simulation (DES) was utilised to analyse the material inflow and outflow of the orepass systems when subjected to the different conditions. The study presented in this paper is based on the Malmberget mine, the second largest underground sublevel caving (SLC) iron ore operation in the world.

Mar 15, 2021

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By S. Shairp

The first commercial application of the Dynatec two-stage zinc pressure leach process commenced operation at the metallurgical complex of Hudson Bay Mining and Smelting Co., Limited in Flin Flon, Manitoba in 1993. A key feature of the successful leaching operation is the presence of iron in solution, which facilitates oxygen transfer in the autoclaves and enables rapid oxidation of zinc sulphide minerals. At the same time, the solution from which zinc is recovered must be essentially iron free. Precipitation of iron from the solution starts in the autoclaves and is completed in subsequent atmospheric purification steps. Conveniently, these iron precipitation steps also remove nuisance elements such as arsenic and fluoride from the solution, while producing solids with good liquid-solid separation characteristics. This paper provides an overview of the current operations in Flin Flon, with particular reference to the behaviour and deportment of iron throughout the zinc plant.

Jan 1, 2006

By Marcel Labbé

La largeur de l?armature peut être modifiée selon les besoins du client entre 48 " et 64" de largeur totale, donc 2 sections de 24" à 32". Ceci permet à l?opérateur d?effectuer le démantèlement de l?équipement pour le déplacement dans les endroits restreints. Le déménagement d?un niveau à un sous-niveau devrait se faire dans un quart de travail de 8 heures. L?option de largeur permet au client de choisir un équipement adapté à son environnement de travail (1). La largeur de la table de forage peut être modifiée selon les besoins du client entre 48" et 96". Cette particularité permet une meilleure stabilité, et plus de précision dans le forage (2). Il y a 4 pattes hydrauliques à chaque coin pour la stabilisation lors de forage (3). La table de forage a 360° d?angle de forage sur 3 côtés du transporteur. La table peut sortir de chaque côté du transporteur de 40 ½" à partir du centre du transporteur pour faciliter la mise en place de la foreuse dans les endroits difficiles d?accès. La plage de forage est considérablement agrandie. Cette caractéristique qui fonctionne hydraulique, permet à l?opérateur de forer sans être obligé de changer la position du transporteur pour des changements de trous. Tous les types de foreuse peuvent être installés sur cette table de forage (4). Sa petite dimension lui permet d?accéder, par des monteries de 30" de diamètre, à des sites de travail de 2,5 mètres de hauteur et largeur. C?est un équipement adapté aux gisements filoniens. Ce genre de gisement est de moins en moins rentable pour les compagnies minières. La mécanisation des ces gisements va permettre de les rentabilisés en augmentant la productivité et la santé du travailleur, en réduisant la dilution (5). Les manettes de contrôle de la foreuse, les mouvements de la table de forage ainsi que le déplacement du transporteur ont été installés selon les recommandations d?un ergonome. Des recherches ont été effectuées par ce spécialiste sur les cas d?accident survenus avec l?utilisation de ce genre d?équipement. Il a déterminé les positions le plus confortable que l?opérateur doit prendre pour éviter les douleurs prolongées (6). Le système de roulement est composé de 4 roues pleines installées sur 4 planétaires de 9000 à 15000 livres de capacité munis chacun d?un moteur hydraulique. Des freins ont été installés sur les planétaires pour assurer la sécurité de l?opérateur et faciliter le positionnement du transporteur lors du forage. Des roues rétractables peuvent être installées pour faciliter l?accès sur rail (7). Ce transporteur peut être alimenté par une puissance électrique plutôt que par une puissance pneumatique. Cette puissance électrique est fournie par un Power Pack qui transforme l?énergie en puissance hydraulique. Ce type d?alimentation est employé lors du forage de développement, mais il peut aussi être utilisé pour le forage long trou. Cet avantage permet au client qui a un problème de pression d?air d?utiliser l?électricité. Par contre si vous utilisez l?électricité mais que dans un secteur isolé le gros courant électrique n?est pas accessible vous pouvez utiliser votre équipement en utilisant la puissance pneumatique. Le changement d?alimentation énergétique se fait facilement (8). Cet équipement est construit pour effectuer 4 types d?activités : forage de développement de niveau et sousniveau avec l?installation d?un bras porteur, forage et pose de câbles d?encrage pour soutènement de terrain, forage de production long trou et forage de monterie ascendante et descendante. L?avantage est que vous investissez dans un seul équipement au lieu de 2 ou 3. Cet avantage vous fait économiser dans votre budget d?équipement. En plus cet équipement est construit pour de dure travaux et ne contient aucun système électronique (9).

May 1, 2001

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some' grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By Robert E. Barieau

This report describes a method for treating pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. The method makes use of a general nonlinear least-squares technique developed at the Bureau of Mines Helium Research Center. It is assumed that an adequate functional form is available for the expression of the compressibility factor as a function of either the molal density or the pressure. The functional form of the compressibility factor can be either linear or nonlinear in the parameters to be evaluated. Formulas are given for calculating variances and covariances of all parameters evaluated and for calculating the variance of calculated quantities of interest.

Jan 1, 1967

By William M. Warren

Recent sinkhole activity in carbonate terranes of Alabama has resulted in damage to transportation lines, structures, utility lines, and property in general. Active sinkhole development and subsidence has been well documented in Alabama, Florida, Pennsylvania, and South Africa. An excellent example of the potential danger resulting from this activity is the spectacular collapse under a South African gold ore crusher plant that resulted in the death of 29 men in 1962. Due to the severity of the problem in certain localized areas in Alabama, a detailed investigation is being undertaken by the Geological Survey of Alabama and the U. S. Geological Survey. One of the most promising techniques is the application of aerial photography and thermal infrared imagery. Conventional and modern remote-sensing techniques are being used in Alabama to locate and define areas of sinkhole activity and to determine which areas are most prone to its occurrence.

Jan 1, 1975

By H. Hejny

The minerals industry, comprising producers and users of industrial minerals and metals, aggregates and ornamental or dimensional stone, oil, gas and derivates as well as coal and by-products, provides vital inputs to Europe's economy and social well-being. Because of their great diversity, minerals and their derived products are necessary for almost every aspect of life. The European Technology Platform on Sustainable Mineral Resources (ETP SMR) unites hundreds stakeholders from industry, the re-search community, public authorities, the financial community, regulators, consumers and civil society around the major technological challenges to the sector, in order to jointly act towards a common vision. The Platform will contribute to strengthening one of the fundamental pillars of the European economy and society. The Strategic Research Agenda (SRA) of the ETP SMR is designed to act as a realistic and inspirational guide to defining a comprehensive research programme that will mobilise stake-holders and ensure that European competences are at the forefront of science & technology worldwide. It will help to stimulate investment in research and provide guidance for policy options. The SRA shows the way the mineral industry has to proceed in forthcoming decades if it is to serve European society in the way necessary. Without a strong European minerals industry, the future development of the EU economy risks to be curbed significantly.

Jan 1, 2006

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By M Kizil

Mining Engineering Degree programs have traditionally had a practical emphasis and have been highly vocational in nature. However, over the years, there has been an increasing attention to the more scientific aspects of the discipline. More recently, the professional institutions, the industry and the community at large have placed increasing emphasis on the broader aspects of the professions: management, finance, humanity, environment and social issues. Notwithstanding this, there has been a continuing emphasis on the practicalities, and most Mining Engineering programs are still strongly vocational in nature. But employers of new graduates complain about the graduatesÆ lack of practicality and readiness for employment æat the sharp endÆ on the mine site.This paper briefly describes some of the more recent developments in the Mining Engineering Degree program at the University of Queensland that attempt to address the problem. Particular attention is paid to alternative learning programs, including applications of virtual reality, practical experience at the University Experimental Mine (UQEM), and the Undergraduate Site Learning Program (USLP).

Jan 1, 2002

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942