Search Documents

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By H. Beecher Charmbury

Water is a most remarkable substance. It is essential for life of all kinds. Not only can no one live without water, but man has always needed water for farming, raising animals, manufacturing, transportation, and recreation. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created by man. However, with our growing population and our ever-increasing demand for goods and services, the public, industry, and government at all levels have become aware of the need to more efficiently manage the water resources of this nation. Coal has helped this nation to become the greatest industrial nation in the world. Coal has generated our electricity, run our railroads, and helped arm our nation during wartime. The result has been the highest standard of living in the world, a time of widespread prosperity, and a national defense potential that has delivered the hardware during four wars in this century. The use of water in coal mining is somewhat different than in most industries. With the exception of the small amount of water used in cleaning plants and for fire protection, most of the water encountered in coal mining operations is unwanted since it serves no useful purpose. In other words, it must be removed, otherwise it will interfere with mining operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface. Ditches were often used to drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water" was generally accepted without too much concern over what

Jan 1, 1973

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

A variety of algorithms and methods are being used by the mining industry today to map mineral resource for reserve estimation. The traditional methods including Polygonal, Sectional and Inverse Distance methods are relatively easy to understand and implement. They have served industry well for several decades and should continue to do so for the large bulk mineable deposits with very regular geometries with relatively small variation in grade.

Jan 1, 1992

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By B. Mather

Discussion by B. Mather I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2Oe; Na2Oe = % Na2O + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete. ? References Mather, B., 1995. "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," Proceedings, Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams, US Committee on Large Dams, Denver, CO, pp. 421-439. Rexford, E.P, 1950, "Some factors in the selection and testing of concrete aggregates for large structures," Mining Engineering, Trans. AIME, Vol. 187, pp. 395-402. Reply by M.L. Lerning Mr. Mather has once again provided a cogent and useful discussion. I am grateful to him for bringing these issues to my attention, as well as to the readers, and I am grateful for his discussion of several important factors in alkali-silica reactivity. Mr. Mather's discussion of the mechanism of alkali-silica reactivity (ASR) notes the critical role of the hydroxide ion. While the alkali hydroxides are highly soluble (reducing the solubility of the other primary hydroxide in pore solution, i.e., calcium hydroxide, and providing hydroxide ions that initiate alkali-silica reactivity), it is, as Mr. Mather quite correctly notes, the hydroxide ion that attacks the silica structure. This point was not clearly stated in my original article. As noted in the text, the requirements for mineral admixtures to mitigate or control ASR vary widely depending on the specific characteristics of the materials

Jan 1, 1998

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

By M. Borowski, N. Szlazak, D. Obracaj

Methods of research and control of the intensity of gas inflow to undersoil layers, after the mines were abandoned are presented in the paper. Gas migration causes them to penetrate to lower storeys of buildings and earthen structures being a menace to people's health and life. The results of measurements of gas concentration in undersoil layers, gas emission to atmosphere and their accumulation in buildings on the territory of closed down mines are presented.

Jan 1, 2003

By J. H. Henderson, L. A. Wilson, R. L. Gergins, R. J. Wygal, D. W. Reed

This paper presents a method of predicting the production history of an underground combustion recovery process. A rigorous solution of the thermodynamics and hydrodynamics involved is beyond the scope of this report. However, a practical scheme to appraise combustion recovery performance has been Worked out. By prudent assumptions, regarding the attainment of steady-state conditions, a trial-and-error solution, which satisfies both material balance and three-phase relative permeability requirements has been evolved and tested. As a combustion zone moves through a formation the interstitial water, the water of combustion and a portion of the oil wil1 be vaporized. These vapors will move downstream to a cooler region of the formation where they will condense. Part of the remaining oil will be displaced by the imposed gas drive and what remains behind will be consumed as fuel. The fluids will distribute themselves downstrean? in a manner which will satisfy the three-phase relative permeability characteristics of the formation. Three distinct zones will exist ahead of the combustion zone: (I) a zone termed a water bank which contains three mobile phases, oil, water and gas; (2) a region containing two mobile phases, oil and gas, called the oil bank; and (3) a zone having the fluid saturution distribution which existed prior to combustion. The mobile water will impose a water flood on the oil in the region containing three flowing phases. The process can be visualized as a simultaneous water .flood and combustion-supported gas drive. It is possible to estimate the saturation distributions in the water bank and oil bank as well as the production history for any combustion temperuture if the porosity, three-phase relative permeability characteristics, oil viscosity and initial saturations are known. This has been done for injection pressures ranging from I to 100 atm, oil viscosities of 10 to 1,000 cp and porosities from 20 to 40 per cent. Several of these calculations have been checked in the laboratory, with the result indicating rather good agreement between the predicted and observed production histories. The analytical and experimental techniques are described and the comparison of predicted and observed performance presented. INTRODUCTION Considerable research by the oil industry during the past 10 years has been directed toward the thermal recovery of crude oil. Of all schemes considered, the one receiving the most attention is in situ combustion. This is a process in which part of the oil is actually burned within the reservoir rock. The uniqueness of the process lies in its potential. Theoretically, this potential generates from the following: (1) it may open the door to vast reserves previously not economically producible, (2) it may induce increased production rates where low rates are now realized and (3) it may give high over-all recovery efficiency. The general idea of the process has received considerable attention in the literature '-' and the following brief description is intended for orientation only. In situ combustion can be visualized by considering a linear system, one end of which represents the injection well and the other the producing well. The formation at the inlet end is raised to ignition temperature by placing a gas or electric heater at the face of the formation or by the ignition of thermite, charcoal or similar material. While heating, the water and part of the oil in the heated region is vaporized and moved out into the reservoir by the injection of gas containing oxygen. In addition, part of the oil is displaced as liquid by the imposed gas drive. The oil not displaced is modified to an immobile, coke-like material (hereafter referred to as coke) by the high temperatures existing immediately ahead of the combustion zone. This coke is used as fuel, and the combustion front advances through the formation at a temperature which is probably in excess of 800°F. As the combustion front advancek it will drive ahead all interstitial oil not rendered immobile and all interstitial water plus the water formed by the combustion of hydrogen. As a result the sand behind the combustion zone is freed of all oil and water. Although the general description of the process has been outlined in the literature, there has been no consideration of the behavior of the fluids moving downstream from the combustion front. It is the purpose of this paper to present a technique

By Xiao Songwen

Based on the anion coordination polyhedron growth unit theory, the polymorph transformation mechanism of antimony white (Sb2O3) in hydro-process was investigated. The new findings had been verified in the commercial-scale test and it was shown that adding a small amount of tartrate ions was economical and effective for polymorph transformation of antimony white in hydro-process.

Jan 1, 2003

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

By V. Sastry

Signgareni Collieries Company Ltd. is operating the JK Opencast Project, at Yellandu, with a rated annual capacity of 1.6 Mt of coal with an average stripping ratio of 4.3. This opencast coal project has three working sections, OC-II block, C-Block and D-Block These workings are operating in close proximity to the JR-5 Longwall Shed, 26-Dip Incline, other structures of 26-Dip, and a Township. There were complaints about ground vibrations and fly rock problems caused due to blasting operations, especially in OC-II and D-Blocks. In view of this, studies were taken up to eliminate the problems of ground vibrations and fly rock.

Jan 1, 2001

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995