Search Documents

By Roger Mourich

As the Powder River Basin coal industry has grown, many changes have occurred in the coal market, the economy and the Basin's methods of dealing with competition in the coal mining business. This article notes the mines that have changed to draglines as the major overburden-stripping tool. The Powder River Basin is defined as those mines within a 97 km (60 mile) radius of Gillette, WY. Mines to the north and south of this area - Decker, Spring Creek, Glenrock - have used draglines more extensively. The reasons for the conversions to draglines at each mine, and the specific timing of these changes, were different. However, the driving factor was economics. As coal production increases, strip ratios increase and coal sales prices decrease, mines must find ways to deal with rising costs and falling revenues. The primary method used has been conversion of overburden stripping to dragline operations. Stripping ratio equals the bank cubic yards of overburden removed for every ton of coal mined.

Jan 1, 1994

By I. R. Muirhead, S. Frimpong

"The mechanization of mining operations in underground coal mines has led to faster cutting rates of coalfaces with increased levels of emission of gaseous and particulate contaminants in the workings. Consequently, the fresh air streams from the main ventilation systems reaching distant workings are often insufficient, ineffective or inadequate and have to be supplemented by auxiliary ventilation systems to create and maintain the required working environments underground. The efficiencies of auxiliary ventilation systems are largely affected by drivers of the system such as the type and capacity of the fan; the type, length, diameter and condition of the ventilation ducting and the distance from the discharge end of the intake ducting to the face. Traditionally, single point measurements of methane gas concentrations using either flame safety lamps or hand-held measuring instruments have been used to assess how safe underground coal workings were. Unfortunately, such occasional measurements of methane gas concentrations do not give an accurate picture of the real gas concentration in the working as they are often taken from the easily accessible locations in working. Continuous monitoring of the methane gas concentration in development headings enables a better assessment of the environmental conditions prevailing there. All variations in the methane concentrations are more easily captured on a continuous monitoring basis than by instantaneous single point measurements. The approach adopted in this work was to continuously monitor the concentration of methane very close to the face and about 60 m outbye in development headings, observe the types of auxiliary ventilation equipment and their sizes being used in the working as well as noting the lengths from the discharge ends of the forcing and exhaust ductings to the face.In this paper, empirical methods are used to calculate the mean efficiencies of the auxiliary ventilation systems in selected development headings in coal mines in North America. This enables the assessment of the effectiveness of the auxiliary ventilation systems and the identification of the system drivers in them. The results show that the efficiencies of the forcing systems ranged from 17.02% to 96.81% while the efficiencies of the overall systems varied from 6.04% to 54.16%. The distance from the discharge end of the intake ducting to the face appeared to be the strongest driver in the performance of the auxiliary ventilation systems studied. It was also noted that when the discharge end of the intake ducting to the face does not exceed 7 m, there were faster purging rates of methane at the face and the efficiencies of the overall auxiliary ventilation system were greater than 50%. These findings are very important in underground coal mining in North America as they will assist to avert calamities, such as the Westray coal mine disaster in 1992 which resulted from the explosion of methane gas, by identifying which components of the ventilation system need special attention to create safe working conditions underground."

Jan 1, 2003

By George H. Willis

In the second half of the 19th century, bimetallism progressively was replaced by gold standard. After World War I and the 1931-33 depression, gold was mainly reserved for official international transactions and internal use was restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses are now financed by Private and official credit, rarely by gold. This historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) its role in the International Monetary Fund, and (5) use as unit of account. For this paper I have tried to take a longer perspective than is usually possible, and to look, even if very briefly, at the changing relationship of gold to the monetary system over the last 200 years or so. There are, I believe, some long-term trends, continuing down to the present day. These trends have seen gold replaced by some form of paper assets in one monetary function after another. These past trends may help us to understand where gold stands now, and possibly will throw some light on the future. Because it seems to me that gold in the past has performed various functions related closely or marginally to money, I have divided this rapid historical review into several sections: (1) the internal and external private use of gold, (2) the internal official use of gold, (3) the external official use of gold, (4) gold and the International Monetary Fund, and (5)gold as a unit of account.

Jan 1, 1980

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Graduate mining and metallurgical engineer now open for engagement. Member, 38 years old, married, 19 years' experience in United States, Europe, South America, Africa, in exploration work, surveying, assaying, mining, milling, ore-dressing, construction and management. Four languages mastered. No. 355. Member, aged 35, technical graduate, desires position -as superintendent or assistant superintendent of spelter or zinc oxide furnaces, or both. Gas producer experience, zinc metallurgical and laboratory experience. Can handle men. No. 356. Member, also Assoc. Mem. Am. Soc. of C. E.; excellent technical education, and best of references covering twelve years in responsible charge of work; experienced in surveys, construction, prospecting, mine examination and development and irrigation work; speak Spanish fluently, and can write a good report. Good executive. Available during June. Age 34; married. No. 357.

Jan 6, 1917

A new series of reports called ?Mineral Perspectives" (MP's) has been initiated by the Bureau of Mines with the publication of MP-1 titled, "Far East and South Asia" by K.P. Wang and the staff of the Bureau of Mines. This new series parallels the creation of the recently announced "Minerals Commodity Profiles" (MCP?s). Both series are designed to provide current information on important sectors of the mineral economy to assist professionals in government, industry, and education in monitoring supply-demand relationships that have significant impact on our domestic economy as well as on the international scene. The orientation of the "Mineral Perspective" series is a geographic one which examines the mineral situation of a region or a country. The "Mineral Commodity Profile? series examines individual mineral commodities. They are in this sense complementary.

Jan 1, 1977

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By M. Yavuz

Determining the most convenient plant location is one of the most commonly encountered problems in engineering applications. This paper presents a fuzzy multiple attribute decision making (FMADM) model which is developed for the selection of the optimum plant location for natural stone factories in the mining industry. The criteria affecting the decision making process in natural stone industry were determined to solve the plant location problem in the FMADM model. To determine the optimum plant location for a new natural stone factory, which is planned to be established by a mining firm located in the Eskisehir region of Turkey, an analysis was carried out by incorporating the method and the analytic hierarchy process (AHP) method. The analysis shows that the Yager?s method can easily be applied to the selection of plant location in the natural stone and mining industry when the difficulties encountered in the application process of the AHP method is taken into account. Keywords: Natural stone, plant location, decision making, Yager?s method, analytic hierarchy process (AHP).

Jan 1, 2008

By Wang Hongwei, Wu Yongping, Cao Peipei, Jiao Jianqiang

Fully mechanized top caving mining of steeply inclined extra-thick seams with variable angles has complex roof rock movement, failure, caving, and filling mechanisms. Moreover, the variable-angle coal seams make rock–equipment stability control challenging. We analyzed rock deformation and failure mechanisms, overburden bearing structures, and working characteristics of supports through physical simulations, field tests, and theoretical analysis of the no. 120210 working face of Zaoquan Coal Mine. Overburden rock movement has distinct regional characteristics, with a large caving height (to the main roof layer) in the upper area, and lower caving height (to the lower main roof) in the lower area. Support loading is regional and unbalanced along the inclined direction. The critical layer of overlying strata migrates, and bearing structures formed by breaking the critical layer exhibit cross-layer generalization along the inclination. The upper region has a cantilever beam structure in the basic roof rock layer; the lower region has an inclined masonry structure with multistage ladders in the breakage basic roof rock layer. Application of a false-inclined working face layout with the tailgate ahead of the headgate and an arc arrangement (radius 28.65 m, arc length 10–20 m) in variable angle areas, and regional control of support working resistance and top-coal caving amounts, control regional failure overburden. Safe and efficient mining was achieved, with the monthly production and recovery rates reaching 344,900 t and 85.86%, respectively. Our results expand the scope of fully mechanized top caving mining and have important theoretical and technological significance.

Nov 23, 2020

By P. W. Bridgman

THE thesis of this article is that the age of Newton is now coming to a close, and that recent scientific discoveries have in store an even greater revolution in our entire outlook than the revolution effected by the discovery of universal gravitation by Newton. The revolution that now confronts us, arises from the recent discovery of new facts, the only interpretation of which is that our conviction that nature is understandable and subject to law arose from the narrowness of our horizons, and that if we sufficiently extend our range we shall find that nature is intrinsically and in its elements neither understandable nor subject to law. The new experimental facts are in the realm of quantum phenomena. Comparatively little has been written for popular consumption about this new realm which has opened in the last fifteen years. The man in the street has been much more interested in relativity, which to him has seemed extremely interesting and revolutionary. Occasionally, however, there has filtered down to him the news that nearly all the theoretical physicists are occupied with a new order of phenomena which they find very much more exciting and revolutionary than any in the realm of relativity. For after all is said and done, the practical effects of relativity, measured in ,dollars and' cents or in centimeters and grams, are exceedingly small, and require specially de- signed experiments executed by men of the highest skill to show their existence at all. The phenomena with which quantum theory deals, on the other hand, are of the greatest practical importance and involve the simplest aspects of everyday life. For example, before the advent of the quantum theory no one could explain why a tea kettle of water boiling on the stove should not give out enough light in virtue of its temperature to be visible in the dark; the accepted theories of optics demanded that it should be visible, but every burned child knew that it was not.

Jan 1, 1929

The Institute published a collective index of- Volumes I to XXXV inclusive, which has been very extensively purchased and used by the members of the Institute. It enables one to look, up any subject in the first thirty-five volumes and is useful to those who have the Transactions, as well as to those who have not, because it tells what subjects have been treated and enables one to look these matters up in his own library and then afterward either to procure the individual papers from the Institute at the price of $1 each, or to procure Volumes, or to consult the Trans-actions at a nearby library, if such a one is available. It now seems desirable to publish another collective index, and the Editorial Department, upon the authority of the Board of Directors, has prepared an index of Volumes XXXVI to LV inclusive. This will be sold in the Institute's standard half morocco binding at a price of $5 and in paper covers at a price of $4. It wilt be ready in a few weeks. Those who already have the first index and purchase the second one, and those who purchase both, will have a complete index of the Transactions from Volumes I to LV inclusive. The Institute will be glad to receive advance orders for this index to insure prompt delivery upon publication.

Jan 8, 1917

By G. F. Comstock

H. M. BOYLSTON, Cambridge, Mass.-It might be asked, since this test is so simple, why it was not discovered before. It seems to me the explanation is that when we have used the sodium picrate solution, it has .generally been on a very, high-carbon or hypereutectoid steel; to detect . the presence of free cementite, and when we have looked for sulphides, it

Jan 4, 1917

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

By Richard D. Hagni

Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in millproducts. The mill dressing engineer should be more aware of the types of beneficiation problem that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations ofthe mineral constituents of an ore or mill product can be visually determined. This advantage provides solutions to many beneficiation problem. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in flocculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 1, 1979

By W. A. Wood, W. H. Reimann, Maria Ronay

The basic mechanism of fatigue is studied in annealed a brass subjectecl to alternating torsion at room temperature, 100°, 200°, 300°, and 400°C, and in air. It is shown that the slip-zone micro-cracking which characterizes fatigue damage produced by small amplitudes at room temperature is progressively replaced by grain boundary cracking at elevated temperatures, replacement being complete at 400°C. Replacement occurs not because slip activity decreases hut because slip movements at elevated temperatures cease to concentrate in narrow zones and instead disperse. Decrease of amplitude at 400°C through permitting longer lives of specimens before fracture actually causes in- MOST studies of fatigue at elevated temperature have been concerned with data for design. Observations on the basic mechanism of fatigue have been largely incidental, though they have led to the interesting inference that this mechanism has features in common with that of creep.' This paper is concerned primarily with the mechanism itself. Advantage has been taken of mater- crease in pain boundary damage, an anomaly attributed to the greater difficulty at elevated tempwature of starting and propagating a crack. Surface corrosion was most pronounced along slip bands but since at elevated temperatures the slip hands showed no cracking the surface corrosion did not appear to influence onset and early spread of fatigue damage. Similarly the type of fatigue damage produced at room temperature by cyclic strain at large amplitudes, characterized by irregular mi-crocracks at zones between disoriented regions in a grain, was also replaced by mainly grain boundary cracking at elevated temperature, though not so completely. ials and procedures known to show readily how fatigue affects the microstructure of a metal at room temperature, so that direct comparison might be made with what the same procedures show when the material is subjected to fatigue deformation at higher temperatures. 1) MATERIAL This was 70/30 a brass, used extensively in previous studies at room temperature.' Specimens were turned from extruded rod to have parallel test portions 1-1/4 in. long and 7/32 in. diameter, annealed to a grain size -1/10 mm, and electro-

Jan 1, 1965

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

The difference between a hypothetical and a theoretical approach is considered and the advantages in using a hypothesis is discussed. Virgin horizontal stresses play an important role in stabilising strata which bridge across an excavation, and reduces the tensile stresses which develop in a beam subjected to bending. Simple formulae are deduced for the bridging of a thick massive stratum under such conditions. At shallow depths, tensile failure on the upper side of the beam is the most likely cause of fracture, but below a certain depth this gives place to compressive failure on the underside, with the possible incidence of rock bumps. The presence of strong massive beds delay the onset of subsidence and may restrict the width of the subsidence trough. If the material involved in the caving is strong, this will reduce the final subsidence, especially at shallow depths. The British regulations for the control of aquifers and their dependence on the strain developed at the seabed are discussed. As an alternative, the concept of a disturbance factor is introduced to permit the consider- ation of aquifers at depth, leading to an explanation of the make of water on the first faces to be mined in the Selby Coalfield. 'Elie paper closes with a brief consideration of the different roles played by longwall face supports in the control of readily cavable strata, and the control of strong beds which hold up in the waste.

Jan 1, 1986