Search Documents

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0' (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,' Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (' transformation is suppressed; but ordering takes place (i.e., 0 -0'). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0' phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b' within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

By John W. Cahn, David A. Karlyn, Morris Cohen

The massive B(bcc) — am (fcc) transformation in Cu-Zn alloys has been studied isothermally by pulse-heating the retained ß phase from room temperature to the reaction temperatures. The transformation is found to occur only in the single-phase a region of the equilibrium diagram. The massive growth rate is of the order of 1 cm per sec and is constant at each temperature, usually after a delay time of some milliseconds. The delay time depends on the reaction temperature in C-curve fashion, while the growth rate increases monotonically with temperature over the single-phase range. The absence of isothermal massive transformation in the two-phase region does not arise from slow growth rates at such temperatures, but because the reaction cannot get started there. It is proposed that the massive transjormation initiates at small preexisting a particles which have rejected zinc into the surrounding 0 matrix. Only within the single-phase region can these particles consume the excess zinc during diffusion-controlled growth and thereby accelerate to the steady-state massive growth rate. The onset of massive growth marks the end of the delay time, and the growth rate then becomes interface-controlled. These isothermal transformation characteristics explain why the usual composition range for massive-kinetic studies by quenching is so limited. The same principles can be extended to more complex alloy systems by recognizing that the single-phase region in which the massive transformation can occur may not be stable with respect to phases not participating in the reaction. MASSWE transformations are now recognized as a regular class of solid-state reactions involving no compositional change (like martensitic transformations) and no shear displacements (unlike martensitic transformations). The name was first coined by Greninger1 in 1939 to describe the coarse grains of fcc a solid solution generated via a fast reaction from the parent bcc 0 solid solution in Cu-A1 alloys. However, some 9 years earlier, phillips2 had already described a similar transformation in the Cu-Zn system. The fact that the massive a formed as a single phase during drastic quenching from the 0 region of the equilibrium diagram signified that compositional changes were precluded. and the reaction was presumed to take place as in a one-component polymorphic transition by nucleation and growth. Phillips also observed that the occurrence of the massive transformation in the Cu-Zn system was extremely sensitive to alloy composition. For example. in a Cu-37.3 at. pct Zn alloy. the ß — am (am = massive transformation product) reaction was found to predominate and was not suppressed by iced-brine quenching from the 0 region. whereas at compositions greater than 38.3 at. pct Zn the massive reaction did not appear at all. Knowledge concerning massive transformations has bee11 substantially enhanced over the years by Massalski and his coworkers; an excellent summary of his papers and the current understanding of this type of reaction has been published recently by Barrett and ~assalski." he massive transformation product grows in roughly nodular form. often with irregular boundaries but sometimes with almost planar interfaces. The latter may have simple crys-tallographic indices relative to the 0 matrix. or the indices may be complex just as in the case of mar-tensites.'1 Little is known about the existence of orientation relationships between the massive and parent phases. A striking feature of massive transformations is that the massive units start almost exclusively at grain boundaries of the parent phase and frequently propagate on a broad front across matrix grains and grain boundaries of various orientations. Because of the rapid growth rate, it is thought that the interface motion is controlled. not by long-range diffusion. but by thermally activated atom jumps across the transformation boundary.

Jan 1, 1970

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By Stephen T. Bloomer

The application of a direct current electrical potential between a metallic pile and a fine grained soil results in an almost instantaneous change in the magnitude of the forces acting on the pile. During installation, with the pile connected as a cathode, the driving force needed can be reduced dramatically. Reversal of the polarity results in an increase in ultimate bearing capacity. The cause of the aforementioned phenomenon has been investigated and found to be two-fold; ie the electro-osmotic transport of pore-water and the electro-chemical hardening of the clay in close proximity to the pile. In the case of the former effect, the pore-water is transported towards the cathodic pile resulting in a temporary, reversible change in the engineering properties of the clay surrounding the pile. This effect is represented by a change in Skempton's Adhesion Factor (a). A total of one hundred and forty eight model tests was undertaken to study the change in the a valve using different types of metallic pile. The tests revealed changes in bearing capacity related to embedded length, skin-friction, end bearing and electro-osmotic gradient. It was shown in skin-friction-only tests that variations in soils strength across the soil profile caused by the electro-osmosis caused resultant changes in bearing capacity. This work is being carried out with the collaboration of Hercules Piling, a subsidiary of Stent Foundation Ltd.

Jan 1, 1996

Water resources legislation in Brazil is evolving in a number ways. The nature of water resource ownership has changed in the last constitution (1988) so that now all water remains the property of the state and not the individual. There is also an increasing amount of legislation to control water access from the environment and regulation over water quality for water discharged. Finally, in some regions charging for water has been introduced and this is expected to become more wide-spread over the next few years. Increasing government attention to water legislation creates an increased need for mine sites to improve water management. As a fundamental basis for this, it is necessary to make robust estimates of mine site water balances, which also requires knowledge of the regional water balance to provide context for the mine water use. A conceptual model for mine site and environmental water balance is presented. Issues associated with conventional water monitoring are discussed. It is proposed that introduction of automated monitoring to provide comprehensive and consistent data is attractive. However, there remain a number of cultural and practical impediments to purchase, implementation and maintenance of effective monitoring, which are summarised.

Jan 1, 2009

The mining of high-grade narrow vein deposits is a predominant field of activity in the precious metal sector. These types of deposits are located throughout the globe and have a significant presence in mining operations. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise ore dilution, the thermal fragmentation mining method enables the operator to extract a narrow mineralised corridor, 30 cm to 1 m wide (according to the true width of the ore vein). By inserting a strong burner powered by diesel fuel and air into a pilot hole previously drilled directly into the vein, a thermal reaction occurs spalling the rock and enlarging the hole to 30 - 100 cm in diameter. This patented method produces highly concentrated ore, resulting in 400 - 500 per cent less dilution when compared to conventional mining methods. The mining method was conceived with the aim of mining ounces, not tonnes. This method of extraction, reduces the environmental impact of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a two-person team, maximises the effectiveness of skilled personnel, increases productivity, and reduces risks of injuries. Important economic benefits are generated for large- and small-scale mining operations alike. For large-scale operations, the mining method increases mining reserves, lowers the cost per ounce, and increases the total profitability of existing mine operations. The method also significantly lowers costs and risks of developing and mining small-scale deposits, requiring less investment capital, shortening the payback period, thus reducing the lending risk.  Combined with a small modular processing unit able to process between 100 - 300 tons per day, the method substantially lowers the financial break-even point for small-scale mining operations in a narrow vein environment. The company has been working with the technology at its Rocmec 1 mining site; results achieved and future developments are discussed.

Jan 1, 2008

By P W. Wypych

The iron ore industry faces significant challenges in the control of dust to meet emissions regulations and goals, as well as ensuring sustainable operations. This paper describes some of the different techniques and innovative technologies that are being developed and implemented to improve the suppression of airborne dust, specifically through the use of high energy micromist sprays. The utilisation of computational fluid dynamics (CFD) modelling and simulation is identified and described as a key enabling technology for an improvement in dust suppression solutions both from a level of understanding the source and flow of dust emissions, and for the development of new systems that can be used in the iron ore industry. CFD modelling is shown to be effective for modelling both spray dispersion and cross-wind effects, allowing designers to develop high-efficiency dust suppression systems with a greatly improved level of confidence when compared to traditional techniques. New high energy micromist technology is also outlined as a key element in developing high-efficiency dust suppression systems. Experimental results and industry applications are presented to demonstrate the significant improvements that can be achieved in suppressing or reducing airborne dust emissions.CITATION:Roberts, J M and Wypych, P W, 2017. Research into improving the efficiency of water spraying airborne dust control techniques in the iron ore industry, in Proceedings Iron Ore 2017, pp 359–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By E. Barsky

"Theoretical notions of mass transfer processes in cascade separation of bulk materials have not been adequately developed as yet (Barsky M.D. 1980). In this paper we have derived linear difference equation of the second order for a cascade with initial feeding top any stage proceeding from mass exchange regularities. The solution of these equations has allowed us to determine quantitative dependences of the material distribution over the cascade stages, which serve the basis of the method of predictive estimate of the process results. We have also examined the model of the material distribution coefficient formation at individual cascade stages.We have checked the adequacy of this model to experimental data. It is noteworthy that the obtained theoretical results are phenomenological, i.e. they can be applied to the processes of separation of different physical nature, e.g. of isotopes, liquid media, gases, etc.INTRODUCTIONRecently, the processes of cascade separation of bulk materials have found broad application in various industries. They ensure a high separation efficiency and high-quality composition of final products. Although specialized literature gives serious attention to cascade processes [1], their theory is not sufficiently developed yet. To achieve optimal organization of this process, we examine mass transfer in a cascade gravitational classifier with stages of identical design."

Jan 1, 2016

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

By Germán Ramón Rojas

El presente texto describe una alternativa de sistema de gestión en seguridad minera con el objetivo de prevenir y controlar riesgos dentro de una estructura organizacional y señalar su importancia en la cultura de una empresa. Para ello, el autor otorga un concepto integral de cómo gestionar el sistema de seguridad dentro de una empresa a través de la identificación y control de los factores críticos de éxito, los patrones de conducta Y de sus empleados; así como del fomento de cultura organizacional de las empresas mineras para una gestión preventiva.

Sep 14, 2009

By A. O. Filmer

The techniques used in this study of the non-oxidative dissolution rates of high- and Iow-grade nickel mattes in hydrochloric acid involved leaching and the use of a rotating ring-disc electrode. It was found that the rate of metal dissolution depends on the potential at which the matte dissolves, a maximum rate of dissolution being observed at -0,2 V to 0,3 V (relative to a saturated calomel electrode). The results are comparable with those obtained in work on the dissolution of synthetic nickel and iron sulphides. The adverse effect of excess sulphur on the rate of nonoxidative dissolution is explained in terms of the mixed potential of the reaction. The leaching studies showed the feasibility of processing a high-grade nickel matte by non-oxidative dissolution, and indicate that maximum rates can be obtained in the presence of fairly Iow concentrations of oxidant. A relative selective dissolution of iron can be obtained from the Iow-grade matte under reducing conditions, thus resulting in a significant upgrading of this material. Letter to the Editor Dravo Corporation is seeking information concerning a special method of transporting explosives to aid in designing a large underground oil shale mine in the mountains of Colorado.

Jan 1, 1981

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003

By E. Garay, J. P. Guzman

El proyecto Hilarión suma 52 Mt @ 4.5% Zn, 0.70% Pb, y 1.0 oz/t Ag en recursos totales (M+I+I a la fecha) asociados a una mineralización tipo skarn en al Departamento de Ancash, en Perú. El yacimiento se encuentra emplazado en rocas calcáreas pertenecientes a las Formaciones Pariahuanca y Pariatambo. El sistema metasomático-hidrotermal está claramente representado por una alteración zonificada representada por una mineralogía de más alta temperatura (diópsido, andradita, wollastonita y rodonita) cerca del intrusivo hasta calizas marmolizadas en las partes más distales. La mineralización consiste en una mena de esfalerita–marmatita y galena argentífera con una ganga de pirrotita, pirita, magnetita y arsenopirita

May 1, 2008

By R. E. Aune

In the present work, a critical assessment of the thermodynamic information available for the ternary system Ni-W-0 has been carried out; This was complemented by experimental measurements of the standard Gibbs energy of formation of the ternary compound NiWO, by solid state galvanic studies involving Zr02-CaO solid electrolyte. The assessed thermodynamic data, together with the phase diagram information available in literature, were employed to generate the ternary phase diagram for the system Ni-W-0 in the temperature range 1073-1273 K. The calculation of the phase diagram was carried out by computer optimization according to the "CALPHAD" method. The computed phase diagram has been confirmed at isothermal sections by identification of the phases present in samples equilibrated at defined temperatures.

Jan 1, 1994

By Jeffrey A. Pontius

The Cresson gold deposit is in the southcentral portion of the Cripple Creek mining district in central Colorado (Fig. 1). The deposit is hosted by a series of 32 Ma (Kelley, 1995) felsic to mafic, alkaline volcanic rocks that were deposited in a diatremal environment. Mineralization in the Cresson deposit is structurally con-trolled. It occurs as disseminated and vein type. Gold deposition is closely associated with potassium-pyrite metasomatism and quartz-telluride vein development(Pontius, 1992). The Cresson deposit is owned by the Cripple Creek and Victor Gold Mining Co. (CC&V), a joint venture between Pikes Peak Mining (67%) and Golden CycleGold (33%).

Jan 1, 1996

By Zetti Gavelan, Eric Ruiz, Emilio Delgado, Ely Loayza, Jesús Cruces

Debido a la variabilidad de la competitividad del yacimiento que está formado por skarn y pórfidos, para mejorar el concepto de conminución en Las Bambas el proceso de reducción de tamaño se inició en el manejo de los factores de carga, diseño de mallas de perforación y diseño de voladura del macizo rocoso. La maximización del sistema de molienda SAG se consiguió de manera sostenible con la integración del equipo de voladura en las optimizaciones realizadas en la planta. De este modo, se logró incrementar el procesamiento a 150 Kton/día.

Mar 30, 2020