Search Documents

KIeeman (1968) described practice in the Mount Hebbard dump concentrator, Broken Hill, N.S.W. The purpose of this note is to give data on flotation pulp chemistry in the plant for comparison with results of Woodcock and Jones (1970a, 1970b).Ten chemical parameters were measured at ten points in the circuit using the techniques of Woodcock and Jones (1970a, 1970b). Fig. 1 shows a condensed time plot of some continuous measurements in conditioner overflow and rougher feed. Fig. 2 shows average values of selected parameters at the start and end of each of the three rougher flotation stages.DISCUSSIONpH and redox potentiaIsFig. 1 shows that pH and Eh were relatively constant at the start of sulphide lead flotation. There was a fairly steady increase in pH throughout the circuit (Fig. 2), but flotation was always conducted in a slightly acid pulp in spite of the large amount of alkaline reagents added. Eh values became more positive as the pulp progressed through the circuit (Fig. 2) in accord with results elsewhere.

Jan 1, 1973

By H. R. Page, A. E. Jr Lee

A. E. LEE, JR. (author)—In addition to the paper we should like to make a few remarks. First, the seriousness of bending of the clay retort cannot be overemphasized. Not only did bending limit the length of the vessel, but it permitted corrosive fluid slags to concentrate in the belly of the retort and thus increased the possibility of boring. Bending also practically prohibited the use of cleanout machines and increased the danger of excessive fume losses by allowing furnace gases to escape around the top of the retort mouth. It will be noted that the Blackwell pottery practice places considerable emphasis on careful drying of retorts. Perhaps it is another smelter superstition, but traditionally the aging of retorts beyond a reasonable drying period has been considered important to long life. We are unable to give a good explanation of why aging should improve retorts. During the past fall in an attempt to prove a theory that the combined water in the clay decreased during aging, about 50 samples of wet retort collars were placed in a dry room when it was closed. Loss of weight, combined water and free moisture were measured each week over the 100 day drying period. The affinity of the dried retort for moisture makes difficult the accurate measurement of free water; however, there was a clearly defined free moisture change from about 12.5 pct when freshly made to about 2 pet at the end of 18 days, then a gradual loss to about 0.25 pet at 70 days and an apparent equilibrium near this figure through the 100th day. There was no appreciable change in the combined water. The change in weight of the average sample was, however, rather unusual, there being consistently a loss of weight throughout the entire 100 days. From the 63rd day on this leveled off to about 0.03 pet per week. These were small samples and certainly should have dried

Jan 1, 1950

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By Morris J. D, Baldwin Z., Wiltcher P. M

21 Moorfields is an oversite development in central London spanning Moorgate tube station. It required the installation of both the highest loaded bearing piles and the highest top loaded static pile test ever undertaken in the UK, at 50.5MN (5,680 tons). The 17-storey building is founded on only 15 large diameter bored piles installed through the roof of the live station. The piles are located in two parallel rows 50 m (164 ft) apart, bridging the underlying train lines and the Crossrail tunnel below. This unique project required a diverse cross-section of skills and experience from the Project Team as we not only pushed the boundaries of design but also those of construction practices. Our team therefore needed to be made up of members from multiple businesses and disciplines. The team worked together, in a highly collaborative environment, for around two years before any work started on site. A key challenge for this project was that there was only one opportunity to construct each pile. If a position had to be abandoned there were no alternative locations and the impact on the project would have been catastrophic. It was therefore vital that all events that may have led to the abandonment of a pile were investigated ahead of commencement on site. Risk elimination and mitigation strategies were developed for all eventualities whether they be associated with the design or construction processes. The successful pile load test, coupled with all contract piles being fully instrumented with state-of-theart fiber optic (CemOptic) cable along their full length, has improved our understanding of the performance of such large and heavily loaded piles. The works piles will all be monitored during the construction of the new building, providing new insight into their real-world performance. Such groundbreaking work has never been undertaken before in the UK and has the potential to significantly influence the industry’s understanding of pile behavior, and design, in the future. This paper will discuss the challenges the team encountered during the design and construction of this highly complex urban project, particularly when adopting, by necessity, a pioneering approach.

By I Ametov, S Harmer, R Alford

A process that allows selective flotation separation of low Cu/S ratio minerals (chalcopyrite and pyrite) from high Cu/S ratio minerals (bornite and chalcocite) from a mixed copper mineral concentrate under controlled oxidative-reductive potential conditions has been developed. The process has been extensively tested on samples with varying mineralogy using laboratory batch flotation tests and mini pilot plant trials.In this process, the mixed final copper mineral concentrate is purged with nitrogen, and then treated with sodium dithionite to achieve a slurry Eh in the -200 to -100 mV standard hydrogen electrode (SHE) range. Flotation was then carried out using nitrogen gas. As a result, a low Cu/S ratio concentrate (<1.3) and a high Cu/S ratio (>1.6) tailing stream were produced. QEMSCAN analysis of the flotation products showed that more than 85 per cent of the chalcopyrite and 95 per cent of the pyrite reported to the froth concentrate. Chalcocite and bornite were almost evenly distributed between the concentrate and tailing streams.Surface analysis studies, focused on the mechanism of separation, showed that at a negative redox potential xanthate and possibly dixanthogen are the dominant hydrophobic species on the surface of chalcopyrite and pyrite. As a result, the flotation of these minerals remained unaffected. In contrast, a much lower concentration of xanthate species on the surface of chalcocite and bornite particles was observed. Therefore, it is likely that at low Eh the copper xanthate complex desorbs from the chalcocite and bornite surfaces, causing a decrease in surface hydrophobicity and the diminished floatability of chalcocite and bornite.CITATION:Ametov, I, Harmer, S, Grano, S and Alford, R, 2014. Selective flotation of chalcopyrite and pyrite from a mixed copper mineral concentrate under controlled redox potential conditions, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J. P. Zannaras

If we assume that testing of the model started at time t1, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. I), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t2 after time t2 motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made. It can therefore be stated that all conclusions and observations of the author from the photographs are applicable only to his small-scale experiments and not to actual mine roofs. Without investigation of the true stresses or the combined maximum stress induced in the beds it has been assumed by the author that failure occurred solely due to bending stress caused by loading of the beds. (The author states that D was taken to be the theoretical strain given by elementary beam theory.) Fig. 1 shows that the beds were clamped together. This clamping was necessary to prevent slipping of the beds due to the horizontal shear. However, this clamping caused an uncontrolled and undertermined com-pressive stress S at the end of the beds, and this com-pressive stress caused a true tensile stress ?S (? PoiS-son ratio). This true tensile stress combined with the tensile stress produced at the end of the beds due to loading (fixed beam uniformly loaded), and the horizontal shear which is maximum at the end appears to be the most probable maximum stress produced in the beds. It is therefore evident that the author in performing this experiment has introduced stresses in the model not existing or dissimilar to actual mine roofs, and therefore his conclusions may be applicable to his small-scale experiments but inapplicable to actual mine roofs. Louis A. Panek (author's reply)—The discusser's difficulty is related to mechanics of materials rather than similitude. The effect of time did not enter into the tests in any way, being simply excluded from consideration in this study, because all quantitative results entering into the design equations are based on measured (between time t1 and time t2) bending strains that are well below the breaking strain (i.e., in the elastic range) for the model material. Time does not become a significant factor until the rock stress reaches 80 to 90 pct of the breaking stress." The objective of this investigation was not to predict that bolted roof will fail after time t, but was instead to develop a safe roof, that is, roof in which the bending strain is much less than (say less than 50 pct of) the breaking strain. The models tested to failure had no direct bearing on the design equations. Although for some rocks time may influence the magnitude of stress or strain at which fracture occurs, breaking stress or breaking strain values were not employed for any purpose in this investigation. Tests to failure were made only to obtain additional evidence regarding the behavior of the bolted laminae' as evinced by the locations of the cracks. As stated in the last paragraph of the paper, if one wishes to predict the time or stress conditions for which the roof will fail, additional information is required. The reason for clamping the laminae is to make them behave liked clamped beams, which closely approximate the clamped-plate condition of the actual mine roof beds (Ref. 5, p. 1; Ref. 6). The writer has previously demonstrated that the bending stresses induced by centrifugal loading in a clamped model beam are in agreement with those predicted by theory;' hence clamping has no significant effect on the bending ,trains measured during a test. Moreover, actual ,in, roof beds are likewise subject to a clamping effect due to weight of superincumbent strata carried by the pillars or ribs on each side of the opening. It is emphasized that this study was restricted to evaluating only the reinforcing effect produced by the bolts. Procedures employed in the experiments and in the data analysis were such as to deliberately exclude the effects of other factors. The objections offered are therefore invalid,

Jan 1, 1957

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By R. L. Neman

Southern Oklahoma (including the Arbuckle Mountains) has outcrops of rocks representing Precambrian, Paleozoic, and Cretaceous ages. Thus, rocks of every geologic age in the Paleozoic and Mesozoic Eras, except the Jurassic and Triassic Periods, are present in south-central Oklahoma. With rocks of such an enormous age range present in a relatively small geographic area, it is little wonder that a wide variety of economic rock and mineral resources are locally present. This report will describe the occurrence, mining, processing, and end-uses (dictated by chemical and physical properties) of the Precambrian Troy Granite, the Cambrian Royer Dolomite and Fort Sill Limestone, Ordovician silica sands of the Simpson Group, Ordovician limestones of the Viola Springs and Welling Formations, and Ordovician Sylvan Shale. In general, the more the end-use depends upon chemical composition and purity, the greater the price that can be demanded for such-minerals. The not-so-successful attempts to mine zinc, manganese, copper, and iron from the Arbuckle Mountains also will be discussed briefly, and I will provide a sermonette on analytical chemistry and its usefulness to corporate CEOs. I may be one of the few persons at this Forum on the Geology of Industrial Minerals who is not a professional geologist. I am an analytical chemist specializing in geochemistry. In particular, I investigate trace elements in rocks and their consequences in industrial processes. As such, I have consulted to the mining industry (and their clients) for two decades, always with the intent of improving service and product quality.

Jan 1, 1999

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By Milton H. Ward

INTRODUCTION Historically, planning a mine involved the economic decision of whether to mine by open-pit methods or underground methods. The method selected was influenced by a number of factors, including size, tenor, and location of the deposit. If the project could not be justified by either underground or open-pit practices, it remained in fallow until economic conditions changed or technology advanced. Technology has advanced and the mining industry now has another option, that of in situ leaching. This method is on the threshold of becoming a commonly used alternative for production in many types of metal and mineral deposits. It will be utilized as the primary method for developing an ore body or as an adjunct to open-pit or underground operations. The following considers application of the technique to a deposit that had been partially exploited by open-pit methods. HISTORY The Big Mike Copper Mine is located approximately 30 miles south of Winnemucca, in Pershing County, Nevada. Interest in the property dates from the turn of the century, but little exploration was undertaken until the mid '60s. In 1967 Cerro Corporation acquired the property and initiated a major drilling effort. Ranchers Exploration obtained the property after this exploration program in late 1969 and confirmation drilling was undertaken. The deposit was delineated and it was determined that reserves amounted to about 100,000 tons of 10.0% massive copper sulfide ore and 700,000 tons of 2 .O% mixed oxide-sulfide ore. The ore body was a lenticular deposit, dipping at 50°. The massive sulfide mineralization was chalcocite and

Jan 1, 1974

By R. C. Miranda

The purpose of this work is to present ?state of the art? mass balances closing strategies in ore treatment plants. It presents a brief history of difficulties and challenges ahead. The current methodology is based on usage of an expert system, which seizes and filters the plant data, analyzes situations of equipment stops and mostly instruments failures. It is still possible to internally create a strategy to check the data of an instrument failure. The system is coupled to software with a Lagrangian model of mass balance closure that receives the pre-treated data. Thus, the data goes through filtering and reconciling processes to generate a reliable mass balance of the ore treatment plant. This made possible to obtain a system that is able to tell the real productivity of a ore plant through reliable mass balances. Residence times on equipments are critical to the balance, thus, they require good logic to eliminate errors due to the characteristics of non-steady state. Among the next challenges is the inclusion of a ?soft sensor? as a replacement of an instrument required for mass balance closure.

Sep 1, 2012

By Dorsey Hager

THE rapid increase of water troubles in the Mid-Continent oil fields is causing much alarm. Troubles occur at Towanda, Eldorado, Augusta, Cushing, Blackwell, and Healdton, although they had, not been acute in the Mid-Continent field until about two years ago, when the unusual conditions in the deeper oil fields were first encountered. California faced the same situation, but, thanks to aggressive measures, has largely overcome the dangers. The following analysis of water trouble may throw some light on the subject and be of assistance in solving the problems involved. WATER TROUBLES CLASSIFIED The presence of water in large quantities in oil sands has the following results: 1. Diminishes oil production. 2. Diminishes casing-head gasoline production: (a) By curtailing the gas flow. (b) By making the use of vacuum pumps unsuccessful. 3. Increases lifting costs: (a) By making it necessary to pump large quantities of water, which requires. a fast motion and long stroke (third hole). (b) By requiring the use of compressors for air lift. (c) By causing break-downs and delays due to the high speed necessary to pump water. (d) By making it necessary to treat "cut" or emulsified oil. Oil production is seriously curtailed by the presence of large quantities of water. Lease records show that wells are shut down 40 to 60 per cent. of the pumping time where serious water trouble occurs. While a small quantity of salt water may cut the paraffine and keep the oil moving, several hundred feet, or a hole full of water, effectually "kills" the oil

Jan 10, 1918

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By S. Tyson

The American Coal Ash Association, Inc. (ACAA) is an organization of producers and marketers of coal combustion byproducts. Since 1968, the goal of ACAA has been to gain recognition and acceptance of ccbs as an engineering material on par with competing virgin, processed and manufactured materials by advancing ccb uses that are technically sound, commercially competitive and environmentally safe. The use of ccbs is affected by local and regional factors including production rates, processing and handling costs, transportation costs, availability of competing materials, seasonal adjustments, and the experience of materials specifiers, design engineers, purchasing agents, contractors, legislators, regulators, and other professionals. An annual, survey of coal-burning electric utilities is conducted by ACAA to determine the quantities of ccbs produced and used in the USA. In 1993 approximately 88.5 million tons of ccbs were produced in the form of fly ash, bottom ash, boiler slag and byproduct from flue gas desulfurization (FGD). Approximately twenty-two percent of the combined production of these byproducts was used, while the remaining portion was deposited in disposal areas. The major markets for ccbs include cement and concrete products, structural fills, road-base layers, mineral filler in asphalt, grit for snow and ice control, blasting grit and roofing granules, grouting, coal mining applications, and waste solidification and stabilization.

Jan 1, 1995

By Omid Marzoughi

In this research, both the kinetics and the mechanisms of the roasting of a sphalerite concentrate from the Bafgh mining complex in Iran were investigated. The oxidation process was performed in a muffle furnace in air and the effects of time and temperature on the degree of oxidation of the zinc sulfide sample were quantitatively studied. The experimental data were fitted to the shrinking core model. In the temperature range of 650–800 °C, the rate-controlling step was the chemical reaction between the zinc sulfide and oxygen with an activation energy of 103 kJ mol−1. On the other hand, in the temperature range of 850–950 °C, the rate-controlling step was oxygen diffusion with an activation energy of 50 kJ mol−1. Also, the roasting process was studied using thermogravimetric (TGA) and derivative thermogravimetric (DTGA) techniques.

By Peter G. Kovalchik, Rudy J. Matetic, Susan B. Bealko, Adam K. Smith

Overexposure to noise remains a widespread and serious health hazard in the U.S. service providing and goods producing industries. Excessive noise can lead to poor verbal communication and reduce the ability to recognize warning signals. These dangerous work conditions can also cause stress and fatigue. Occupational hearing loss is a permanent illness, with no recovery currently possible. Method: National Institute for Occupational Safety and Health (NIOSH) has recognized Noise Induced Hearing Loss (NIHL) as one of the ten leading work related diseases and injuries in the United States, and has emphasized its importance as one of the critical areas expressed in the National Occupational Research Agenda. Results: One of the most serious noise problems in the goods producing industries is the operation of continuous mining machines during underground coal mining. In order to minimize occupational hearing loss, noise hazards are “designed out” early in the design process. NIOSH is leading a national initiative called Prevention through Design (PTD) to promote this concept. This paper describes the quiet by design approach of a noise control that reduced noise exposures of continuous mining machine operators by 3dB(A) using the four functional areas of PTD, namely Practice, Policy, Research, and Education.

By S. Tavani, R. E. Browner, R. Dunne

Lead is used in CIP/CIL circuit to increase the leaching rate of gold from ores. At least four mechanisms have been proposed for the action of lead in gold leaching circuits: (I) precipitation of sulphides as highly insoluble lead sulphides preventing consumption of cyanide and oxygen; (2) su,face reaction on sulphide particles forming an insoluble lead sulphide layer peventing dissolution of those sulphides; ( 3) precipitation of lead sulphide, which undergoes further oxidation to soluble lead sulphate recycling the lead to solution,· ( 4) contact reduction of lead onto the gold szaface which then acts as a secondary oxidising agent. Rotating disc studies using a pure gold disc show that small amounts (5ppm) of sulphide ions are sufficient to significantly reduce the leaching rate of gold. Lead increased the leaching rate at small concentrations but at higher levels decreased the rate of leaching. The detrimental effects of lead were only found for a pure solution when leaching the gold disc. Ores mediate the amount of lead available by ads01ption/reaction, thus, reduced leaching rates from excess lead are not serious even when 500ppm of lead ions are added to the sluny. The detrimental effects of sulphide ions could be countered by lead addition during the leaching process. A penalty, in the form of reduced leaching rate, will occur the longer lead addition is delayed. A time lag was noted between the addition of lead and the increased leaching rate when a large concentration of sulphide ions was present.

Jan 1, 2000

By William H. Emmons

Jan 1, 1912