Search Documents

The methods employed in dressing 'the tin ore up to the required percentage of purity depend mainly on the type of ore crushed.These may be briefly divided into two distinct classes-viz., q, free: milling ore and a complex milling ore. In the former the ore is practically free from the common metallic sulphides, such as pyrites, mispickel, blende, galena, etc., and 1!' clean concentrate of 70 per cent metallic tin can be directly obtained in one continuous act of concentration; in the latter, however, in order to get a good extraction, it is only advisable to primarily concentrate up to 30 to 40 per cent. tin oxide, the rest being the sulphides of the metals. This concentrate is then roasted, re-ground, and re-concentrated up to 70 per cent. metallic tin on a separate set of tables.In the complex milling ore the tin is intermixed very closely with the sulphides, so that it becomes necessary to collect all the mineral present in order to obtain clean tailings. Stamp mills are the most popular machines for the primary crushing in the district, but whether they are invariably the best for the purpose is rather an open question. No doubt for some of the very tough chloritic ores they are the most efficient, but for a brittle quartzose ore, such as the free milling proposition usually is, the writer thinks Oornish rolls would well hold their own, especially when the tin occurs coarse, as is so often the case with this class of ore. Of course, the great drawback to stamps is the excessive quantity of tin slimed and slime tin is one of the problems of tin-dressing-while rolls give...

Jan 1, 1907

By Alain Jardy, Valerio De Felice, Jean-Pierre Bellot, Ismael Lis Alves Daoud, Stephane Hans

"Gas-stirring ladle treatment of liquid metal has been pointed out for a long time as the processing stage mainly responsible for the inclusion population of specialty steels. A steel ladle is a complex three-phase reactor, where strongly dispersed inclusions are transported by the turbulent liquid metal / bubbles flow. We have coupled a population balance model with CFD in order to simulate the mechanisms of transport, aggregation, flotation and surface entrapment of inclusions. The simulation results, when applied to an industrial gas-stirring ladle operation, show the efficiency of this modelling approach and allow us to compare the respective roles of these mechanisms on the inclusion removal rate.IntroductionThe reduction of the weight of high performance materials together with the improvement of mechanical properties and the increase of the recycling of used metal are new challenges which emphasize the importance of metal cleanliness. Ladle treatment of specialty steels has long been described as the secondary metallurgical process mainly responsible for the non-metallic inclusion derived from the deoxidation process. The treatment is accomplished by blowing argon through one or more porous plugs for the purposes of desulphurization, minor composition adjustments, and inclusion removal. Gas injection is applied on routine basis to achieve both the stirring of the liquid bath (thermal and chemical homogenization) and the entrapment of the inclusions by the bubbles (flotation). Furthermore, the turbulence produced in bubble swarms enhances the probability of inclusion collisions and makes aggregation the first mechanism for particle removal. The physical processes involved in gas stirred ladles are numerous and complex owing to the three dimensional and multiphase (metal-gas and inclusions) nature of the reactor. Despite these difficulties, the population balance equations can be implemented in CFD code11'21 and combined CFD-PBM (computational fluid dynamics - population balance method) models are investigated for steel ladle processes13'41 and produce very promising results in terms of inclusion removal efficiency."

Jan 1, 2012

By H. I. Kaplan, C. Laird

Pulsating contpresslon experiments have been carried out on coppev single crystals in order to test the adequacy of mechanisms which have been suggested for stage I cvack grouth when tension-compression loading is the mode of- applying stress. Although dejorrrzation continues slowly for many millions 01 cycles under Pulsating compression stresses both within slip bands formed in the first cycle and by the creation of new bands, the morphology of these bands is not typical of fatigue slip bands in general and neither initiation of cracks nor propagation of artificially induced cracks was observed. It is therefore concluded that 1) initiation and growth of cvacks in fatigue is a consequence of repeatedly reviersed, microplastic deformation rather than intermittent, unidirectional deforma-tion, 2) gvowth of- cracks in polycrystalline specimens FAILURE of a plain specimen subjected to cyclic tension-compression stresses is known to take place by two stages of cracking.1,2 The first stage is characterized by propagation along slip planes roughly at 45 deg to the stress axis, in the outermost layers of the specimen, and at a rate of the order of angstroms per cycle. The average macro orientation of a stage I crack is normally at right angles to the stress axis,3 however, except in a few cases, e.g., single crystals in suitable orientation, when both the micro and macro directions of propagation are at 45 deg to the axis. After a stage I crack has penetrated to such a depth that the stress on the remaining section of metal is significantly increased, stage II crack propagation succeeds stage I, at right angles to the stress axis both micro and macroscopically. Direct evidence of the processes occurring during a subjected to pulsating compression stresses is caused by the setting-up of local tensile stresses due to interactions between grains, and 3) both unslipping mechanisms and operation of the "plastic blunting process " within a single slip band are adequate descriptions 01- stage I growth, being fundamentally similar. The slip mode of a material, however, is considered to control whether unslipping or the plastic blunting process takes place. Thus materials of planar slip mode fauor unslipping while those hacing a wavy mode, and capable of cross slip, can fail in stage I by the plastic blunting process. Similarly, and perhaps more importantly, reversed torsion and tension-compression modes of applying stress may be expected to cause the unslipping mechanism and the plastic blunting process, respectively. single stress cycle4,5 shows that stage II crack propagation takes place by a repetitive plastic rounding and closing of the crack tip. This mechanism has come to be called the "plastic blunting process".6 On the other hand, the extreme smallness of the phenomena occurring in stage I growth prevents elucidation of its mechanism by direct observation. Many suggestions have been proposed for this mechanism,'"-" most of them involving some kind of random or systematic unslipping process. It is possible, however, that the mechanism of stage I growth is essentially the same as that of stage 11, but occurring on a much smaller scale.6 In this situation, it has been observed that cracks propagate along slip bands comprising dislocation cell structures and bounded on either side by regions of different dislocation density and distribution." Since there is evidence that such bands are softer than their matrix, * it may be expected that the plastic blunting process occurs within a single slip band during stage I growth, rather than on two gross bands as in stage 11, when the acting stress is greater.= The blunting of the crack tip allowed by coordinated

Jan 1, 1968

By D. Harper

The National Pocahontas Mine in Wyoming County, WV, has been developed in the Pocahontas No. 3 coal. During 14 months of ventilation surveys, the locations of large rockfalls, many in areas infrequently visited by mine personnel, were mapped. Several dozen rockfalls were later studied in detail. Kettlebottoms, rider seams, root-penetrated roof strata, slicken sides, and shales that spall are common in areas with a high density of rockfalls. Large-scale crossbedding and micaceous and carbonaceous films in sandstones are less common. Density of rockfalls in any area is related to the time elapsed since mining, thickness of overburden, and orientation of entries and panels. Some linear features overlie areas where rockfalls are densest. Most rockfalls occur during summer.

Jan 1, 1983

By Alan G. Fricker

Cyprus Gold NZ Ltd will be recovering residual free cyanide in barren gold pulp by air stripping. Laboratory investigations by DSIR have indicated additional advantages by recovering the cyanide from pregnant pulp. These are a lower leach pH, a greater cyanide recovery and less carbon consumption. They have a net economic advantage of $1.20/tonne over recovery from barren pulp. The realisation of these advantages is dependent on three crucial technical aspects -optimum pH for dissolution, the absolute loss of cyanide and the stability of the aurocyanide ion. The laboratory investigations described herein address these aspects. Earlier work had indicated that the rate of dissolution of freely revolving gold discs at constant cyanide ion concentration increased with decreasing pH from 11 to 8. Attempts to repeat the work in a more controlled manner by measuring the corrosion potential and current density have, to date, not been reproducible, but do not contradict the earlier observations. Cyanide recoveries and balances were obtained on leaches at pH 10.5 and 9 at the same cyanide ion concentration -the lower pH requiring three times as much total cyanide. Unaccounted-for losses, unfortunately, exceed the accounted-for losses, making interpretation of the balances difficult. Nevertheless, it appears that the additional amount of cyanide at the lower pH of 9 may not be fully recoverable. It may not, however, prove necessary in practice to use more cyanide at a lower pH. Both the gold and silver cyanide complexes remain available for carbon adsorption, as do mercury, copper and iron. Zinc, and probably cadmium, nickel and lead, may precipitate during stripping, which is an environmental advantage.

Jan 1, 1991

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

By H. E. Stauss, J. Hino

INTEREST in silicon has arisen again in the past decade as a result of improvements in crystal rectifiers.' Although the preparation of silicon was first reported by Berzelius in 1880, the early product was of relatively low purity, and only the need for rectifiers in World War II led to the production of a 99.9+ pct pure powder. This material in crystalline form was consolidated into massive silicon for use, and the method developed was to melt it with selected added constituents as "doping" agents. Melting techniques, therefore, are of great importance. There are two basic problems in producing silicon ingots free of doping additions; one is the prevention of spitting and the other is prevention of cracking of the ingot during freezing. The most satisfactory arrangement yet developed for producing massive silicon is to melt and freeze in a cylindrical quartz crucible surrounded by a concentric heating element and concentric radiation shields or insulation. For example, use can be made of a tubular heater with a high frequency generator as the source of power and reflecting shields of alundum cylinders. The spitting of silicon is related to gas evolution, and the gas comes from two primary causes—adsorbed gas and the reaction products of silicon and the crucible. Gas is also released from bubbles contained in the quartz crucible walls. Improved removal of adsorbed gas can be achieved by means of controlled melting and freezing. The seriousness of the problem in vacuo is reduced with an electrically operated mechanical movement of the high frequency power coil. The upper portion of the powder charge is melted first and the high frequency coil lowered until the powder is completely molten. During cooling the high frequency coil is raised slowly. These means also reduce the final nonviolent extrusion of large beads of metal through the ingot top during freezing. Better control of spitting and bead extrusion is obtained when melting is done under helium at. atmospheric pressure instead of in vacuo. The problem of reaction between silicon charge and crucible in practice is confined to the reaction between silicon and quartz. This2 apparently is: Si + SiO2 + 2SiO The part that this reaction plays in spitting has not been isolated for separate study. SiO is a volatile vapor at the melting point; of silicon and is released freely during melting in vacuo, but hardly at all in helium at atmospheric pressure. The cracking of ingots is a major difficulty in melting silicon, and its prevention requires special melting techniques or the addition of "toughening" agents such as aluminum or beryllium.' The cracking of the ingots has been explained as being the result of the expansion that occurs upon freezing; although direct observation of freezing ingots reveals visible cracks on the surface only after a red heat has been reached, suggesting that cracking is the result of differential contraction of silicon and quartz. Silicon wets quartz, and the ingot adheres tightly to the crucible. Therefore as ingot and crucible cool, the two either have to pull apart, or at least one must crack. Surprisingly, in spite of the relative thinness of the quartz and the thickness of the ingot, the ingot and the crucible both crack. Microscopic and X-ray4 studies fail to show any plastic flow other than twinning in the ingots. Slow cooling fails to prevent cracking. Another possible solution to cracking is to weaken the crucible. Use of thin-walled crucibles finally led to success with fused quartz crucibles with a wall thickness of 0.25 to 0.50 mm. With such thin-walled fused quartz crucibles consistently uniform success is secured in producing sound ingots 30 mm in diam from the purest available grade of silicon (99.9+) without the use of any type of addition. Melts are made in the size range of 50 to 100 g. Omission of a deliberately added doping agent is not sufficient to insure pure ingots. The reaction of silicon with crucibles and the resultant solution of impurities in the silicon is well-established." In this laboratory, the presence of Al, Be, and Zr has been found spectroscopically in ingots melted in contact with alumina, beryllia, and zircon. The best crucible materials reported in the literature are MgO and SiO2. Use of MgO in this laboratory has resulted in a heavy deposit of magnesium on the furnace walls, showing that a reduction of the magnesia occurred and the resulting magnesium removed from the melt by volatilization. In the case of quartz, the silica is reduced and SiO liberated to deposit on the equipment walls. There probably is real danger that oxygen is dissolved in the ingot when either magnesia or silica is used as the crucible material. Preliminary analyses by Dean Walter in his vacuum unit in this laboratory6 indicate the presence of oxygen in undoped silicon melted in quartz.

Jan 1, 1953

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By M. Barsky, E. Barsky

A study was conducted to elucidate the relationship between the hovering velocity and the particle settling velocity. The experiments were carried out in a water medium on five materials ranging in density from 1.070 to 4.000 kg/m3. Analysis of the results with allowance for the distribution of stream velocities over the cross section of the pipe revealed that the final settling velocity of the particles was equal to their local hovering velocity (on the stream axis), and not to the average velocity of vertical flow as is generally believed. It therefore follows that the kinetic structure of the stream must be taken into account when constructing theoretical models of the process for purposes of computation. In addition, the optimal stream velocity is not always equal to the hovering velocity and in fact is governed by other factors as well. Illustration is provided by the results of a study conducted in a vertical cascade classifier comprising eleven identical stages. The feed material was introduced at each stage successively beginning with the topmost (i* = 1 ) and ending with the lowermost (i* = 11). First, the stream velocity that yields optimum separation conditions at each stage of the cascade (i.e. k=50%, k being the yield of a given size class in the fines for a single stage) was sought. Subsequently the conditions of optimal separation for the instrument as a whole were determined (i.e. F(x) = 50%, F(x) being the yield of a given size class for the entire instrument). The results of the study are presented in the table.

Jan 1, 2003

By William J. Ferguson

At Henderson Operations the 24-kilometer conveyor system consists of three main conveyors with lengths of 1.2 km, 16.7 km and 6 km. Upon commissioning of the conveyor system, the Henderson maintenance department was challenged with the inspection and monitoring of over 50,000 idlers. To take a proactive approach to idler maintenance, an idler tracking database system was developed. Using the idler tracking program, the Henderson Crush & Convey department now has the ability to provide data for engineering solutions to idler problems and to manage thousands of idlers for priority replacement work and warranty purposes. Recognizing the potential for injury to Henderson employees in the process of idler handling, Henderson approached idler replacement as a material handling process. Material handling solutions have resulted in failed idlers being replaced and discarded from the underground environment without ever touching a human hand. This paper will detail how Henderson tracks idlers in all primary conveyor belts and how an innovative idler handling system can result in reduced risks to conveyor maintenance employees.

Jan 1, 2004

By Kumara Rachamalla

North American mining companies are lagging behind their global competitors in participating in the outstanding opportunities in India. The Indian government has liberalized foreign equity participation in the mining sector by up to 50% and, in some cases, even higher. Delegates from Europe, North America and South Africa learned this at an information seminar held in London, England, Attendees were welcomed by L.M. Singhvi, the UK's high commissioner for India. He introduced a government of India delegation headed by B.P. Baishya, minister of steel and mines. Singhvi is an eminent jurist and leading constitutional expert. He reiterated the soundness of India's legal system. He also outlined the recent Investment Protection Treaty between India and the United Kingdom. Baishya emphasized thee geological diversity and strengths of India's domestic market with its population of more than 920 million people the second largest in the world after China and its reservoir of skilled labor. He also outlined the potential of India's untapped natural resources. The private sector is the backbone of the Indian economy. It accounts for 75% of gross domestic product (GDP). The current minimum program of the new United Front government envisions 12% growth in the industrial sector, 7% in GDP and direct foreign investment of US$10 billion a year. "Mining is an area that can attract a sizable part of this investment," Baishya said. "Projected growth of the Indian economy will require increasingly large quantities of basic raw materials, such as coal and base- and precious-metals to meet the needs of domestic and export markets." Administration of India's mining sector is divided into the Ministry or Mines for regulating and developing the country's mineral resources, five public sector Mining Enterprises, the Geological-Survey of India (GSI), the Indian Bureau of Mines (IBM)and 25 states and seven Union Territories. The GSI is the second oldest (founded in 1851) and the third largest organization of its kind in the world, Baishya said. It has geologically mapped more than 90% of India's 3.2 million kmz (1.2 million sq miles) at a scale of 1:50,000. Several promising mineral projects have emerged from regional exploration programs conducted by GSI and the Mines and Geology State Governments. IBM recently completed a national mineral inventory. It covers 13,000 deposits/prospects of 61 nonferrous minerals. GSI also compiled a similar inventory on 61 coal fields. India is attractive to exploration companies for several reasons. These include favorable geology, accessible locations and a large mineral database. India also has many experienced geoscientists with well-equipped and efficient laboratories, Baishya said. Secretary to the Ministry of Mines A.C. Sen emphasized the largely untapped-geological and mining potential of India. He also discussed the new vistas that have opened up opportunities for exploration and mining. India has large quantities of mineral reserves, Sen said. Its vast Precambrian Shield - like those in Canada and Australia - is endowed with gold, platinum group and base metals, as well as coal and industrial minerals. Annual mineral production is valued at more than US$7 billion. Sen pointed out that India is the largest single consumer of gold. And domestic gold prices command at least a 20% premium above international prices. Recent diamond, gold and base-metal discoveries and prospects uncovered by GSI have generated investment interest from abroad, he added Delegates heard that the Indian Constitution gives the central government the job of framing legislation and the regulation and development of minerals. This ensures that mineral laws are uniform throughout the country. However, the right to grant mineral concessions, such as prospecting licenses and mining leases, rests with the minerals' owner. In India's case, that is the state government. The Indian government has formulated several guidelines that regulate the granting of prospecting licenses for large areas. ? The central government will consider the requests of state governments for the granting of prospecting licenses for areas exceeding 25 kmz (9.6 sq miles). But the license must include a provision to conduct aerial prospecting of the area. ? Any prospecting licensing area should not exceed 5,000 kmz (1,930 sq miles). for a single license. And the total area held by one company should not exceed 10,000 km2 (3,861 sq miles) for the whole country. ? The grant of larger areas will be linked to a mini- mum expenditure commitment on physical targets. State governments will monitor these expenditures. ? The granting of large areas for prospecting will be linked to a schedule of relinquishment.

Jan 1, 1997

By B Ganesia, H Sahupala

PT Freeport Indonesia is a copper-gold mine operation located in West Papua, Indonesia about 3500 km east of Jakarta. Current ore production is about 270 000 tpd, of which 30 000 tpd comes from underground. In the future, the production from underground will be gradually increased to reach a maximum of 115 000 tpd, as the Grasberg open pit production decreases. The current and future challenge for PT Freeport Indonesia is to fill the quota of underground miners, as Indonesia does not have a long culture of underground work. At present, there are only three active underground mines in Indonesia. The lack of underground skilled labour incited the company to develop its own skilled workforce. In the mean time, to overcome the shortage of personnel, the underground management had to find a way to improve the productivity. Since 21 May 1998, PT Freeport Indonesia Underground Mine has operated with the new roster of two rotating shifts a day, 11 hours per shift. The previous schedule consisted of three nine-hour shifts per day, six days a week, for a total of 26 working days in a month. This change was intended to increase the productivity of the miners. With the previous roster, studies determined that the effective working time was only seven hours per shift. The new roster produces an improvement of effective working hours to about nine hours per shift. As a result, total production has increased by 33 per cent and the utilisation of production equipment has increased by 16.5 per cent. This paper describes the background of the decision to change the work schedule, the study carried out to evaluate the benefits and drawbacks of the new shift roster, the challenges, and then compares the results for various parameters between the old schedule and the new one.

Jan 1, 2002

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By T. Takasu

Overall productivity in copper refining is currently determined by the electrorefining process. Previous research showed that forced convection of the electrolyte improves the morphology of the copper deposit on the cathode and suppresses passivation of the anode. In this paper, electrorefining experiments under forced convection were carried out in the presence of As, Sb and Bi impurities, both in electrolyte and in the anode, to determine the effect of the impurities on the electrorefining process. The concentrations of the impurities in the deposit increased with increasing current density without forced convection. An increase in the fluid velocity suppressed the increase in impurity concentration. These concentrations were high, especially in the initial stage of deposition without forced convection, corresponding to a decrease in the cathode potential measured during that period. This indicates that the enrichment of impurities was induced electrochemically. The reason for the decrease in cathode potential was the low concentration of copper ions on the electrode surface because of ion consumption by the electrolysis. The forced convection of the electrolyte enhanced the ionic mass transfer and thus suppressed the polarization and deposition of the impurities. The fluid motion was shown to be effective in achieving electrolysis under high current density conditions.

Jan 1, 1999

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By Charles B. Ingram, Neil E. Gehrig

The development of water gel explosive products has been the single most important development in explosive research and development since the invention of nitroglycerine and dyne-mite many years ago. m e Explosives Department of Gulf Oil Chemicals Company has been engaged in the research, development, manufacturing an marketing of slurry explosives and blasting materials for over twenty years. Explosive research and development is being carried out at the Jayhawk Technical Laboratory and the Underwater Testing Facility near Pittsburg, Kansas. There are fourteen manufacturing facilities geographically located around the country to serve the mining, quarrying, and construction industries with a complete line of explosives, blasting agents, and accessories. This paper discusses the Gulf slurry products, their properties, and uses.

Jan 1, 1977

By G. C. Wallick, W. R. Foster, J. G. Savins

The theory of the differentiation method for the Couette flow experiment is reviewed. Particular attention is given to the requirements on data analyses in the case of the class of non-Newtonian materials described as viscoplastics, i.e., materials characterized by a yield point or yield stress. Here changes in boundary conditions arise when the shearing stress attains a critical value with the result that the form of the basic integral equation for Couette flow is determined by the flow conditions existing during the measurement. INTRODUCTION In the preceding papers in this series,l,2 the salient features of the differentiation method of rheological analysis in Poiseuille-type flow were discussed. It was shown that a dual differentiation-integration method analysis of the Poiseuille flow of idealized generalized Newtonian and visco-plastic models could be used to develop a spectrum of highly sensitive response patterns in terms of certain characteristic derivative functions. These functions were shown to optimize the selection of the most appropriate functional relationship between f(p) and p from the Poiseuille flow experiment. The present paper reviews the theory of the differentiation method as applied to the equally important Couette flow experiment. We will also discuss the range of variables over which the basic integral equation for Couette flow is applicable when the non-Newtonian material is of the viscoplastic type, i.e., characterized by a yield point or yield stress. THEORY Having described the application of the differentiation method to Poiseuille-type flow in the preceding papers, we now proceed to the case where the test liquid is confined to the annular space between coaxial cylinders of length L, one of which is in motion, i.e., Couette flow, formulating the basic integral equation after the method of Mooney.3 The observed kinematical and dynamical quantities are the angular velocity O and the torque T. Here, the one nonvanishing component of the shear-rate tensor is

Thermo Fisher Scientific is a supplier of samplers, instruments, analysers and consumables to the mining industry under the Thermo Scientific brand. The critical need to provide a representative sample to the analyser has played a pivotal role in product development. Products discussed are the Analysis and Sampling Station (AnStat) for mineral slurries, the Coal Quality Manager (CQM) and the prototype Bore Hole Analyser (BHX) with optional drill chip recovery system. Analytical techniques used in the above products are XRF, PGNAA and LIBS respectively. The company also designs and supplies conventional mechanical sampling equipment and complete sampling systems for bulk material applications (historical Ramsey brand). These products and application of them are presented.

Jan 1, 2008