Search Documents

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By E. S. Anolick, Joseph Singer

The magnetic after-effect, in the form of time decay of permeability (l/µ), has been used to obtain independent data on the solubility of&apos; carbon in pure iron. The results differ slightly from the solubilities obtained through internal -friction experiments. The mechanism of the time decay being the magnetic analogue of internal friction, it appears necessary to explain the observed discrepancies, and some suggestions are made. THE purpose of this work was to establish the reliability of the time decay of permeability as a measure of dissolved interstitial in the body-centered-cubic lattice, and further, to establish techniques suitable for such measurements with samples of a form convenient for various other measurements. This particular sample form was the "epstein" strip, i.e., 25 cm by 3 cm by 0.035 cms. While the general conclusions are not limited by this geometry, there are two aspects of the samples that may be relevant: a) texture, and b) grain size, which ranged generally from 1 to 10 mm. Effects due to these two possible parameters were thought to be small and were not investigated. Calibrating the time decay technique and the other experimental procedures by measuring the solubility of carbon in pure iron suggested itself because of the accumulation of data on this subject through the related technique of the internal friction&apos;; The essentials of this report have been published in a somewhat condensed form.5 Since then some additional data have been taken. It is the purpose of this paper to add these data and to provide more complete description of the experimental techniques than was possible then. The time decay of permeability is a form of the magnetic after-effect.6,7 Permeability is measured immediately after demagnetization (µº) and also long after (µ8). The time decay, ?(l/µ), is the difference 1/µ8 - 1/µ0 and has been considered to be proportional to the concentration of a dissolved interstitial6,8,9,12 The relaxation time! 7, is characteristic of a particular diffusion, and affects the permeability as follows: where he being the activation energy for diffusion of the interstitial. Reference is made to the works of snoek6 and Neel7 for a complete discussion. A brief exposition of the principal ideas may be in order here, as follows. On the basis of the simplest model, resistance against domain wall motion increases with time after demagnetization due to the diffusion of interstitials to preferred sites created by the magnetostrictive tetragonolization under the strong magnetic field. Thus permeability, measured with a small field after the abrupt removal of the large field, will continuously fall with the process of diffusion of the interstitials, and the total "time decay" (or "time decrease") should be proportional to the amount of interstitial in solid solution. In the present report, use is made only of the total time decay rather than of the nature of the progress of the decay; the only problem involved in this approach is the need for assurance that only one interstitial is contributing to the effect as used. It is felt that the special use made here of the total time decay warrants the conclusions. Other work has been going on elsewhere on the detailed study of the nature of the time decay.8&apos;9 EXPERIMENTAL A) Materials—12-lb ingots were made in a vacuum furnace from high-purity iron and by a series of hot and warm reductions were brought down to 14-mil strip. This was cut into 25-cm epsteins. The pure iron was decarburized at 750 °C by hydrogen. The time decay measurement for the decarburized iron (see below) indicated a satisfactorily low starting level of interstitials. Grain growth to grain sizes of 1 to 10 mm was produced in the pure iron by a 700" anneal in hydrogen after a critical reduction of about 7 pct as suggested by previous trials. No measurement of texture in the pure iron was made. The grain size was taken to be large enough to be beyond any sharply critical size regarding solubility. B) Infusion of Carbon—Since the permeability measurement required about two dozen epsteins, a special method of carbon infusion had to be developed to ensure homogeneity of infused carbon. This was accomplished by setting the samples edgewise in a

Jan 1, 1961

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By L. C. IlsLey, M. W. Von Bernewitz

"Introduction.Several hundred thousand open lights are daily carried in coal mines of the United States, each lamp being a menace to life and property through fire or explosion. They have been responsible for many disasters in the past, and will be again. Flame safety lamps have been available for over a hundred years, but during the last ten years safe and practical electric lamps have been perfected. These have eliminated many of the flame safety lamps, and in a few mines have replaced open flame lamps. But there are still more than twice as many open lamps as electric lamps in our mines, and the open lamps should be discarded in favor of an approved type of electric lamp. There are several electric miners' lamps which have been approved by the Bureau of Mines for safety and efficiency, give good light, and are easily maintained and carried, some flame safety lamps will always be used, hut mostly for detecting gas; although they might be supplanted if some simple, reliable, and cheap gas detector were developed.Explosion Hazards from Open Lights.An open light and gas*** constitute a vicious hazard; while if there be coal dust present in the vicinity the consequences are multiplied many times. An open light and black blasting powder also constitute an explosion hazard, vividly attested by several serious disasters."

Jan 1, 1924

By James D. Bennett

During the past decade many U.S. industries have realized the importance of a total loss control program; the bituminous coal mining industry is no exception to this trend. Oftentimes, we realize that the circumstances surrounding a "near miss" (an incident which does not result in personal injury or property damage) are practically identical to those associated with a fatality, disabling injury, or major property damage. And, many organizations suffer enormous financial losses in cases where no one is injured or property damaged but costly delays in production result. Detailed analyses of both injury and non-injury cases can provide valuable input into those engineering, behavioral, and management controls that are necessary to prevent their recurrence. The purpose of this paper is to describe a comprehensive loss control surveillance system (LCSS) that will enhance management control in preventing personnel, property, and production losses, thereby, maximizing profit. The next section describes the components of this LCSS. Then, we present one practical example of how this valuable management tool can be used to minimize loss through safety and training programs.

Jan 1, 1985

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By Jessica Elzea, Haydn Murray

The term bentonite was first proposed in 1898 by Knight, a year after he had named this clay taylorite, because taylorite had been previously used for another mineral. The name taylorite was after the Taylor ranch, the site of the first mine, near Rock River, WY, and the name bentonite is from the Benton Shale in which the clay was thought at that time to occur. The Benton Shale was, in turn, named after Fort Benton, MT, located more than 640 km miles north of Rock River. Early in the 20th century, several geologists recognized that bentonite, mainly in beds in Cretaceous and Tertiary rocks, originated from transported volcanic materials. This recognition led to definitions based on origin, the one most widely quoted and generally accepted by geologists is the following definition by Ross and Shannon (1926): "Bentonite is a rock composed essentially of a crystalline clay-like mineral formed by devitrification and the accompanying chemical alteration of a glassy igneous material, usually a tuff or volcanic ash; and it often contains variable proportions of accessory crystal grains that were originally phenocrysts in the volcanic glass. These are feldspar (commonly orthoclase and oligoclase), biotite, quartz, pyroxenes, zircon, and various other minerals typical of volcanic rocks. The characteristic clay-like mineral has a micaceous habit and facile cleavage, high birefringence and a texture inherited from volcanic tuff or ash, and it is usually the mineral montmorillonite, but less often beidellite." The difficulty in applying the foregoing definition to bentonite as an industrial mineral commodity is that it is based on origin and is restricted to an ash, tuff, or volcanic glass parent material. Therefore, deposits consisting of the clay minerals required by this definition, but having uncertain origin or parent materials, cannot properly be called bentonite. Furthermore, many deposits in the western United States and in other countries that have formed from rocks other than the types required by the definition are being mined and sold as bentonite. Perhaps the best definition of bentonite as an industrial mineral is one given by R.E. Grim in a plenary lecture at the International Clay Conference (AIPEA) at Madrid, Spain, June 27, 1972. According to this redefinition, which will be used in this chapter, bentonite is a clay consisting essentially of smectite minerals (montmorillonite group of some usages), regardless of origin or occurrence. This definition solves the problem of the difference between the geologic and industrial usages of the term and overcomes the difficulty in assigning a name to smectite clay that formed from igneous rock other than ash, tuff, or glass, or those of sedimentary or uncertain origin. However, bentonite, when used with this meaning is still a rock term (consisting of more than one mineral), and it will not be possible to distinguish it from fuller&apos;s earth in many instances. One way of classifying bentonite is based on its swelling capacities when wet or added to water. Bentonite having sodium (Na+) as either the dominant or as an abundant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium (Ca++) is more abundant than other ions has much lower swelling capacities than sodium varieties. Some calcium types swell little more than common clay, and most crumble into granular masses in water. Intermediate calcium-sodium bentonites, the so called mixed types, tend to swell moderately and to form gels of lesser volumes than equal masses of the sodium type bentonite. Because of the general relationship of swelling and exchangeable ion characteristics bentonite is commonly divided into the high swelling or sodium, low swelling or calcium, and moderate swelling or intermediate types. The term sub-bentonite (Davis et a]., 1940) is used inconsistently in industry for the low or moderate swelling varieties. The authors believe the use of this term should be discouraged because of its implication of low quality or low value and the lack of a mineralogical or use basis for it. In the United States bentonite is also classified by geographic location and the uses for which it is sold. Inasmuch as most of the low swelling calcium type occurs in states bordering the Gulf of Mexico, this variety is commonly called Southern bentonite. The largest high swelling sodium bentonite deposits and the major producing districts are in Wyoming and adjacent states. Therefore, this bentonite is commonly called the Wyoming or Western type. Such terms as drilling mud bentonite, foundry bond bentonite, and taconite bond bentonite relating directly to use are applied in marketing. Other terms including high and low yield bentonite, high and low gel bentonite, and high and low strength bentonite are also used to distinguish different grades. The varied classifications notwithstanding, bentonite occurs in so many different varieties that some cannot logically be classified according to any of the foregoing groupings. One of these types is hectorite, which is a high swelling lithium-bearing variety of smectite occurring mainly in California and adjacent states. It is, therefore, not a Wyoming type, and it occurs even farther west than the so called western bentonites. Others are bentonites having magnesium (Mg++) or hydrogen (H+) as the most abundant or dominant exchangeable ion. These types are neither sodium nor calcium varieties, and apparently some are low swelling, whereas others have rather high swelling capacities. Still another type of bentonite, the so-called potassium type, K-bentonite, or metabentonite, occurs in Ordovician and other Pa-

Jan 1, 1994

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By W Patton, I Minniakhmetov, H Talebi, U Mueller

The sustainability of mining projects is linked to informed investment decisions based on public reporting of exploration and mineral resource estimation results. In Australia, public reporting guidelines are established by the Joint Ore Reserves Committee reporting code through the JORC Code (2012). Although the assessment of uncertainty in the results reported is a requirement, this is often communicated qualitatively and evaluated subjectively. This can become a liability particularly in the early stages of mining projects when spatial domains of geological interpretation and mineralisation envelopes inform resource estimations’ reliability. A recent review of JORC reports found no reports used quantitative assessments of the geological interpretation or mineral resource estimation envelopes, and 27 per cent of reports did not address the question of quality of geological interpretation. Reports that did address the quality used 19 different terms to communicate quality. This work presents methodologies for quantitative uncertainty assessment and communication and explores how they could be applied in public reporting practice. Quantitative uncertainty reporting would benefit mine planning and financial modelling as they normally assume the geology is 100 per cent right (since no error is reported or only a single deterministic model is provided). The complexity, cost, and additional work of doing a quantitative assessment could hinder a straightforward implementation. This could be overcome if mining companies budget for quantitative uncertainty assessment and associated professional development. A compulsory requirement for the inclusion of uncertainty assessments in public reporting or adopting standardised subjective language would improve industry practice.

Mar 22, 2022

By Andrew Cushing, Joe Carvalho, Jon Hurt

"INTRODUCTIONThe shales of the Greater Toronto Area (GTA) have been known to experience time-dependent deformations (TDD); those initiated by excavation-induced stress relief which progress with time as a function of rock porewater salinity, access to freshwater (or air) of lower salinity, clay and calcite content, and the buildup of swelling pressures within the rock mass. These deformations can induce long-term pressures on shaft walls and tunnel linings, especially if the permanent works are constructed soon after excavation, with very little time delay. This paper presents measurements of time dependent deformation of recent shaft and tunnel projects constructed in the GTA, and draws conclusions regarding the main influences on the TDD. The key input parameters for the numerical predictive model are critically assessed. Projects which are discussed include the Billy Bishop Airport Pedestrian Tunnel, Hydro One Midtown Tunnel and Hanlan Feedermain (Contract 3).MECHANISM OF TIME DEPENDENT DEFORMATIONExplanation of MechanismThe Georgian Bay Shale unit consists of typically moderately weathered to fresh, grey to dark grey, fine to very fine grained fissile shale interbedded with slightly weathered to fresh grey, fine grained calcareous siltstone and limestone interbeds. There are two distinctive features of the shale in the Greater Toronto Area (GTA). One is a high horizontal stress regime, and the second is long-term time dependent swelling behavior which develops when the following factors occur (Lo and Micic, 2010):• Stress relief of the rock mass• Outward salt concentration gradient from pore fluid of the rock to the ambient fluid• Availability of fresh waterThe swelling is a consequence of the reduction in confined stress in the rock which occurs upon excavation in combination with a differential gradient in salinity between the saline rock porewater and freshwater or even humid air. Osmotic and diffusive processes result in a decrease in the salinity of the rock porewater achieved by an overall increase in the water content, resulting in volumetric expansion of the shale rock over time. The development of this time dependent deformation (TDD) relative to the time"

Jan 1, 2016

By X. Zhu, R. Du Plessis, J. D. Miller, D. G. Kotylar

Research on the low-potential hydrophobic state of pyrite with potassium amyl xanthate (PAX) as collector, is reported to help explain and understand the fundamental aspects of the N2TEC flotation process, which was originally developed for the improved recovery of gold from refractory auriferous sulfide ores. Typically in the N2TEC process, air is replaced by nitrogen as the flotation gas, and potassium amyl xanthate is used as collector for the reactive auriferous pyrite particles. The first N2TEC flotation process was commissioned at Lone Tree in Nevada in March 1997 and has been in operation ever since. On the basis of electrochemically controlled contact angle measurements, the low-potential, low-pH hydrophobic state of pyrite has been examined as a function of flotation variables such as pH, gas-phase composition, collector concentration and pyrite potential.

Jan 1, 2000

By Clarence Hall, Spencer P. Howell

This bulletin deals with the characteristic features of the principal explosives used in mining and engineering operations, and espe- cially with the tests that show the suitability of different classes of explosives for different kinds of work. The Bureau of Mines pub- lishes the report as one of a series dealing with tests of explosives and methods of reducing the risks involved in the use of explosives in mining operations. The application of explosives to engineering and mining opera- tions has increased rapidly in recent years. According to a pre- liminary report issued by the Bureau of the Census, 469,000,000 pounds of explosives was manufactured in this country during the year 1909, and the greater part of this production was used for industrial purposes. In large engineering projects and in mining operations requiring the use of explosives the selection of a suitable explosive from the many varieties offered for sale is of fundamental importance. Vari- ous considerations are involved in the selection of an explosive of proper class for the blasting to be done. Many explosives suitable for quarry work are unsuitable for use in deep mines or in close workings. In metal mining and in driving tunnels the character of the gases evolved by the explosive on detonation is an important consideration. An explosive for use in gaseous or dusty coal mines must be formulated and compounded so that its flame temperature and the height and duration of its flame are reduced enough to per- mit its being used with comparative safety. In wet workings or in submarine blasting explosives impervious to moisture are requisite. In extremely cold climates explosives that do not require thawing are desirable, provided they are equally good in other respects. An essential requirement of all explosives, especially of those for use in tropical countries, is that they shall remain stable without change in chemical or physical characteristics.

Jan 1, 1913

Robe River Iron Associates (RRIA or Robe) is widely regarded as the worldÆs most cost-effective, consistent and reliable supplier of iron ore. It has been in operation since 1972 and globally is the fourth largest seaborne trader in iron ore exporting 25.5 million tonnes of -9.5 mm sinter fines and 4.5 million tonnes of pisolite lump (-31.5 +6.3 mm) during 1999. Robe is a joint venture that controls major iron ore resources in the Pilbara region of Western Australia. ItÆs participants are North Limited with an interest of 53 per cent (65 per cent including minority interests) and Japanese companies Mitsui (33 per cent), Nippon Steel Australia (10.5 per cent) and Sumitomo Metal Australia (3.5 per cent). Robe River Mining Co Pty Ltd manages the project which is a subsidiary of North Limited and Mitsui.

Jan 1, 2000

By Peter J. Koros

The current wave of interest in this topic is the result of increased use of titaniferous ores or ilmenite in blast furnace burdens for the purpose of repairing hearth damage. The titanium compounds that promote deposition of ?patching? materials in blast furnaces are the cause of downstream problems in the steelmaking shops. Steelmakers historically have objected to significant amounts of titanium in hot metal (>0.10 % Ti) for several reasons: 1) accretions caused by the TiC.TiN needles that float out of the iron as it cools in transit and in transfers make the accompanying slag sticky and crusty, causing problems in desulfurization and increasing time and Fe yield loss at the subsequent raking, 2) defensive measures have been taken in treatment, such as use of argon for carrier gas, but without technical rationale for this approach, 3) difficulty in removal of the ladle slag by the raker, with subsequent sulfur addition to the vessel charge, and 4) transfer into the BOF and/or formation of a very corrosive TiO2 containing acid slag during the early part of the BOF blow which, in addition to causing lining damage, results in loss of sulfur removal capability by the vessel slag. Based on a conceptual analysis of the metal-slag-atmosphere interactions during transfer ladle desulfurization treatment, a mechanism is postulated for the apparent effectiveness of the use of argon in reducing the deleterious effect of titanium and an alternate technique, possibly more effective, is proposed. As probably the use of argon causes increased exposure to atmospheric oxidation of the titanium carbonitrides contained in the ladle slag, the same benefit can be obtained by use of either oxygen or an air blast to oxidize the noxious reaction compounds. Validity of the concept has been demonstrated in a pilot plant setting. These issues, and related effects on testing the hot metal, are examined in detail with reference to the literature and plant and laboratory experience.

Jan 1, 2006

By H. Arima, Y. Kudo

In general, the iron content of zinc leach residue produced by sulphuric acid leaching from calcine is disposed as jarosite or goethite into a tailing dam. More recently, these iron residues have been treated pyrometallurgically to avoid waste disposal. The Iijima refinery selected a different zinc leach residue treatment process for iron control when it was established in 1971. The Iijima refinery is the only plant in the world that has processed a zinc leach residue by the combination of SO2 pressure leaching and O2 pressure hematite precipitation. The process enhances zinc recovery and recovers gold, silver, copper, lead and rare metals in saleable by-products. This paper focuses on the two stages of autoclave application in the zinc leach residue treatment process. The detailed flowsheet and recent advancements to improve the quality of by-products are discussed.

Jan 1, 2004

Discussion of the paper of J. IV. GWINN, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 239 to 247. GIRARD B. ROSENBLATT, Salt Lake City, Utah (communication to the Secretary*).-The storage-battery locomotive certainly has its place in metal mining and I an) glad to note that it is now receiving the recognition that is its clue. It is, however, not a panacea for all conditions of mine haulage. There are places where it will not work to advantage and cannot compare with` the trolley-type locomotive in cost of operation or in cost of maintenance. On the one hand, there are places where it clearly outshines the trolley-type locomotive. Much depends on the headroom available in the drifts and on the condition of the roof. For short hauls with moderate-

Jan 5, 1915