Search Documents

By Joseph H. M. Beaty, Gust Bitsianes

Successful blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blastfurnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO - 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which CO2 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature corn bustion of carbon above the tuyeres. Assuming that 1000 Ib. of limestone is used per ton of pig iron, about 435 Ib. of CO2 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb, would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1943

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

The granitoid rocks in Burma can be subdivided into three main belts viz. (1) Eastern Granitoid Belt, (2) W-Sn related, Central Granitoid Belt and (3) Porphyry Cu (Au)-related, Western Granitoid Belt. The W-Sn related, central belt Granitoids were interpreted to have generated during the continent-arc collision and the Porphyry Cu(Au)-related, western grantioid belt was emplaced in a magmatic-volcanic arc above an east-dipping subduction zone. INTRODUCTION Major tectonic domains of Burma Burma region can be subdivided into N-S trending (6) major tectonic domains from west to east (1) Arakan Coastal Strip as ensimatic Foredeep (2) Indo-Burman Ranges as Outer Arc or Fore Arc (3) Western Inner-Burman Tertiary Basin as Inter-Arc Basin (4) Central Volcanic Belt (Central Volcanic Line) as Inner Magmatic-volcanic Arc (5) Eastern Inner-Burman Tertiary Basin as Back-Arc Basin and (6) Shan-Tennasserim Massif as ensialic, Sino-Burman Ranges (Bender, 1983). The Sagaing (transform) Fault and Shan Boundary Fault form as a tectonically significant boundary between Eastern-Burman Basin (Back-Arc Basin) and continental,

Jan 1, 1987

By S. G. Luckey, N. R. Harrison, F. Nadeau, U. Brüx

"The adoption of tailored-rolled or tailor-welded blanks (i.e. TRB/TWB) in the automotive industry has been known to offer great potential for the optimization of weight, function, cost and complexity. Vehicle light weighting can further be achieved by using high strength aluminum alloys like the 7xxx-series. 7xxx-series alloys are capable of delivering specific strengths equal to or greater than high strength steels. However, room temperature formability of this aluminum class is limited, so one approach to forming 7xxx-series alloys is by hot stamping. Hot stamping utilizes an elevated temperature blank and the high pressure stamping contact of the forming die to simultaneously quench and form the sheet. This paper explores the initial feasibility of tailored thickness material for body-in-white applications when processed under hot stamping conditions.INTRODUCTION Steel tailor-rolled blanks (TRB) or tailor-welded blanks (TWB) have been used within the automotive industry as a method of reducing weight, expanding material utilization, and decreasing overall part/assembly cost (Ganeasan et al., 2015; Merklein et al., 2014; Hirt et al., 2005; Kridli et al., 2000). The production of such tailored thickness materials has resulted in over $2.5 billion (2016) in combined industry sales (Mubea, 2018). As automakers begin to adopt the manufacturing practices traditionally reserved for steel such as tailor rolling/welding with greater enthusiasm for vehicle light weighting, there exist an opportunity to expand the material database to extend beyond the traditional aluminum alloys found in current production. High strength aluminum alloys, i.e. 7xxx-series, are ideal for structural automotive applications due to their high specific strength; however, they have limited room temperature formability. Hot stamping, another manufacturing practice used by the steel industry, can be used to form these high strength materials. The combination of tailoring the thickness of a sheet material and hot stamping provides an opportunity for significant weight saving within an existing manufacturing footprint. This paper explores the potential and challenges of this approach when applied to structural body-in-white components. The methods for tailor rolling, tailor welding and hot stamping are described and applied to the production of a 7075 aluminum alloy B-pillar. The results are discussed in terms of feasibility and weight savings."

Jan 1, 2018

By T. S. Spicer

The relationship of coal characteristics to the principal types of firing equipment has been known to the coal combustion engineer, but is not as familiar a subject for purchasing agents, salesmen, consumers, and executives of coal-producing and consuming companies. This general survey of characteristics determined by standard laboratory tests, of major types of combustion techniques, and of the relationships between the two is directed toward the latter audience. It will also serve as a review for those actively engaged in the combustion of coal. Although the relationship of coal characteristics to the principal types of firing equipment is well known to the experienced coal combustion engineer, apparently there is need for a summary article on this subject. The author has received numerous requests for such a paper from purchasing agents, coal salesmen, coal customers and executives of coal-producing and consuming companies. Consequently, the scope of this paper will be directed to this audience, with the hope that it may serve also as a review to others actively engaged in the combustion of coal. The magnitude of this subject is so great that only a brief general treatise is possible. The author realizes that because there are so many special cases and exceptions to the generalities which follow, he is in jeopardy of contradicting himself. It is the hope, however, that the many references cited will prove valuable to those who wish to study the details excluded by necessity, due to space and time limitations. Hence, the characteristics of coals as determined by standard laboratory tests will be discussed; the major types of combustion techniques reviewed; and then the characteristics and firing will be related. CHARACTERISTICS OF UNITED STATES COALS The coals of the United States range from lignite to anthracite and each has its own general characteristics. The extensive coal fields of the U. S. are shown in Fig. 1 and the estimated reserve according to rank for each state is illustrated in Fig. 2. Coals may be classified according to rank as shown by Table I from the ASTM Standards on Coal and Coke, D-338-38.1 The basis of this classification is ac- cording to fixed carbon and heating value (Btu per pound) calculated to a mineral-matter-free basis. The high-rank coals are classified according to fixed carbon on the dry basis; and the low-rank coals according to Btu on the moist basis. Agglomerating and slacking (weathering) indices are used to differentiate between certain adjacent groups. While rank is not itself a characteristic it does signify certain characteristics that accompany a class of fuel. Anthracite, for example, immediately implies a hard, free-burning, smokeless coal of low volatile matter, usually having an ash of high fusibility. Coals may also be classified according to grade as described by ASTM Designation D-398-37.1 This quality classification is determined by size, calorific value, ash, ash-softening temperature, and sulfur. This type of classification is not used as extensively by the industry as the rank classification. Fig. 3 shows the heat value of different ranks compared to proximate analyses. Coals may also be classified by sizes, as shown in Tables IIA and IIB, and sizes can be on both top and bottom limits. If this is done, then the coal is called double screened; otherwise, either top or bottom sizes can be specified as a limit. Bituminous coal sizing varies from field to field and depends upon the market demand. The common sizes and their main uses are outlined in Table IIA. Anthracite is usually available in many sizes at the colliery, and Table IIB summarizes standard sizes and names. Although rank, grade, and size designations help identify and describe a coal in question, there still remain other characteristics such as indicated by moisture, free swelling index, grindability tests, etc. A bituminous coal information chart Table III) suggested for use in studying the available coals in a region, lists origin and chemical and physical characteristics. Even this more comprehensive list does not completely spell out all the characteristics of a heterogenous material like coal. For example,

Jan 1, 1961

By J. A. Herbst, K. Rajamani

INTRODUCTION Recent research has shown that popu- lation balance models hold considerabl e promise as a basis for accurate mill scale-up from laboratory batch grinding tests. It has been shown that entire product size distributions from large ball mills can be predicted from data obtained in tests in small mills with errors of less than one or two percent. This level of accuracy has been demonstrated for batch grinding scale-up (Herbst and Fuerstenau, 1980; Austin, 1973; and Malghan and Fuerstenau, 1976) and for continuous grinding scale-up (Herbst, et a1., 1976; Herbst, Rajamani and Sanchez, 1982; and Herbst, Rajamani and Lo, 1982) in commercial mills up to 14.5 x 32 feet. A procedure which has been proposed for commercial mill design using the population balance approach and specific power information is shown in Figure 1 (Herbst and Fuerstenau, 1980). Here batch grinding data (size distributions for various energy inputs) obtained in a small batch mill is input to an estimation program which determines the "best" set of breakage rate parameters from the data provided. In turn, these breakage rate parameters are input to a scale-up program along with traditional inputs such as: a) desired circuit throughput and product size b) circuit operating conditions including fraction of critical speed and fractional ball load, size distribution and % solids in feed and circulating load (if closed circuit). In addition, since the population balance approach relies on more detailed models of the grinding circuit sub- processes than the classical design methods do, it is necessary to provide input to the scale-up program on the nature of material transport through the mill (e.g. residence time distribution information) and classifier performance characteristics (e .g. selectivity functions). The scale-up program will make the design calculations including the selection of mill dimensions and drive requirements, will predict product size distributions throughout the commercial circuit and will provide information on the sensitivity of the design to errors in the design assumptions. In order to implement such a scale- up scheme it is necessary to have a computer program for parameter estimation and a program for scale-up prediction. A program which is suitable for parameter estimation, ESTIMILL, has been developed and tested on a wide variety of ores at the University of Utah. This program has been in use in

Jan 1, 1982

By W. Langer

Of the 50 or so most often utilized industrial minerals, more than two thirds are, or have been, produced in the western states of Arizona, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah, and Wyoming. Some commodities, such as natural aggregate, currently are produced in all 13 states; others such as beryllium and iodine are produced in only Utah and Oklahoma, respectively. Together, the 13 western states make a significant contribution to the US industrial minerals industry.

Jan 1, 2007

By John S. Berber

Acids, neutral oils, and pitch were produced by distillation of low-temperature lignite tar and processed to upgrade them into more valuable products: The acids were separated from the distillate and catalytically dealkylated to produce phenol, cresol, and xylenol. Aromatic and naphthene fractions of the neutral oil were converted into phthalic and maleic anhydrides by catalytic hydrodealkylation and vapor- phase oxidation. Paraffins and n-olefins from the neutral oil were processed into alkybenzene sulfonate, a biodegradable substance. Aromatic materials from the neutral oil were also extracted with organic compounds and the extract hydrogenated under pressure to produce jet fuel. The pitch was processed by various means to change its characteristics and make it suitable for similar applications as high- temperature tar pitch, including preparation of carbon black and metallurgical electrodes. In most cases, products obtained from the low-temperature tar were examined for physical and chemical characteristics and for potential commercial utility. Information obtained from this research would be helpful if a new coal- chemical industry based on tar utilization were established.

Jan 1, 1973

By D. B. Eccleston

Natural gas and mixtures of natural gas and hydrogen were used as fuels in a laboratory engine to determine the relationship of emissions to air-fuel ratio and to establish practical lean limits for air-fuel ratio. Synthetic gas manufactured from coal (Synthane) and natural gas were used as fuels in a vehicle to obtain comparative data on emissions and performance. Results showed that lean limits for air-fuel ratio when using hydrogen-enriched natural gas were extended significantly beyond Chat of natural gas. Synthane pro¬duced exhaust that was significantly less reactive than exhaust from natural gas. With lean air-fuel ratios, the acceleration performance of a vehicle fueled with Synthane was improved over its performance when fueled with natural gas.

Jan 1, 1972

By C. F. Austin

lined-cavity shaped charge is an explosive mass with a cavity at one end and the detonator at the opposite end. The cavity is lined with a dense material, such as metal, glass, or a ceramic. Such an explosive device can be a useful drilling tool. Lined-cavity shaped charges are constructed to do just one thing — create a high-velocity jet of liner particles that can bore a hole in a target. The liner must be smooth and symmetrical, and high-velocity, high-brisance explosive must be used rather than ordinary commercial dynamites. Since the depth of target penetration is related to jet length, a standoff distance should be provided to hold the charge a short distance from the target. This allows the jet to lengthen prior to target impact. The best results are obtained when the jet is perpendicular to the target surface. Charges can be positioned for firing by taping them to a stake or simply laying them on a flat surface at the proper distance and angle with respect to the target. EFFECTS ON THE TARGET When a jet strikes a rock target, the jet and target particles at the jet-target interface move outward radially with respect to the jet axis to create a tremendous compressive load on the target material immediately below the target surface. The result is a shallow crater formed by spalling at the point of target entry. After cratering ceases, the steadily deepening hole continues to form as a result of the jet's imparting radial motion to the target particles at the jet-target interface. These radially moving particles collide with one another and with the hole walls, the net motion of the spent jet particles and target particles being back out of the hole in an axial direction (the backblast). The backblast keeps the penetration free of debris during penetration, al- though loose surface rock often falls into the hole after penetration ceases. The sudden stress relief after penetration ceases sometimes results in minor hole-wall rebound, which can partially fill the hole. The hole bottom will taper as the jet velocity decreases, until the jet velocity is too low to maintain the backblast. At this point the remaining jet and the following slug material are simply packed into the hole bottom. HAZARDS INHERENT IN USE Air blast from the highly brisant explosives used in shaped charges can damage nearby structures

Jan 1, 1961

By Luis Tavares Ribeiro

Dynamic programming is based on the-, application of a simple property formulated by Bellman in his principle of optimality (Bellman, 1957): "An optimal policy has the property that whatever the initial state and initial decision are, the-remaining decisions must constitute an optimal policy with regard to the state resulting from the first decision". The method is charaterised by: (Dowd, 1979) a) A function defining the total value at each decision time of the system. b) The set of permissible decisions. c) The present state of the system. d) The number of steps remaining before the procedure is terminated.

Jan 1, 1982

By William P. Blacutt

This paper examines Bolivia's General Environmental Bill recently passed by Congress: a multi-purpose law with two primary objectives: a) the protection and conservation of the environment, and b) the promotion of sustainable development. In this law, environmental benefits are emphasized by stating general principles, not by attempting to define the means. Regulations are left to the writing of subsequent complementary codes. This paper shows that much of the controversy surrounding the legislation disappears when it is seen as guide rather than an operational part of Bolivia's industrial policy. In essence, the law addresses recent environmental awareness in a region more anxious than ever to speed economic growth.

Jan 1, 1992

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick's Law in 1947, through to today's models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By Joseph Pogue

THE prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry.

Jan 3, 1924

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992