Search Documents

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

The difficulty of finding new ore bodies, the complexities of patenting them when they are found, and the absence of incentive legislation for exploration have limited mining exploration in the United States mostly to the big companies. This situation, coupled with ECA spending abroad, has caused American capital to look outside our national boundaries for investment opportunities which are further made attractive by some relaxing of restrictions to gain American dollars and patronage.

Jan 1, 1950

By M. S. Badollet

"DURING the past five years, production of asbestos fibers has increased in all countries that list asbestos as one of their mineral resources. Despite the many small mines that have been opened in Canada, United States, Mexico, South America, Italy, South Africa, Australia, Yugoslavia, and Rhodesia, the supply still does not meet the demand. It is estimated that total 1952 world production of asbestos fibers of all varieties approximated 1,600,000 tons, with Canada supplying 966,382 tons (I), or 60 per cent of all fiber mined.Asbestos fiber brokers continually are offering odd-lot samples of chrysotile, amosite, crocidolite, tremolite, and anthophyllite fibers to manufacturers, •quoting fantastic prices for tonnages •varying from just a few to 50 or more in a month. In many cases, the samples are not properly graded and contain quantities of rock impurities and finely ground dust.When vendors submit samples of asbestos fibers, the manufacturer should consider• them in terms of price, quality, quantity, and as possible substitutes for fibers currently used in his products.Grading of these odd-lot fibers in most cases has been poorly done, with resultant non-uniform fiber lengths. In some instances, a number of miscellaneous lots of fibers have been .blended for sale. This blending produces a fiber that is difficult for the manufacturer to accept as a substitute for the well-standardized Canadian fibers."

Jan 1, 1953

By D. G. Krige

Recent publications have demonstrated the important role that can be played by a priori information of the grade levels, variability, and spatial patterns in adjacent or nearby areas in improving the quality of grade estimates for virgin or sparsely drilled areas. A research project was therefore conducted involving the collection and analysis of extensive sampling and borehole data from 7 reefs on some 30 Witwatersrand mines. This paper shows that the 'equivalent' log variance for the two-parameter lognormal model provides a good basis for the study and comparison of the levels and behaviour of relative variances. The trends of these against the corresponding log areas were found to form distinctive patterns, which are useful for these purposes. The patterns for the Basal, Vaal, Carbon Leader, and Main Reef Series form a reasonably close group, whereas those for the V.C.R.(particularly where the facies are mixed), B Reef, and Kimberley-Elsburg Reefs (particularly for narrow channel widths) do not always conform. The patterns shown by underground chip samples are also compared with those obtained from borehole cores. It is shown how this information can be used to improve the borehole valuation of new mines and of virgin areas in existing mines.

Jan 1, 1993

By C. Karageorgos, J. Sakala, A. Prinsloo, B. Ngambi

The sulphide flotation circuit at First Quantum Minerals’ Kansanshi mine in Zambia produced over 100,000 t of copper in 2019. For this circuit, mineralogical analysis has shown that the majority of the copper lost is hosted in fine liberated chalcopyrite, which is a paramagnetic mineral. The objective of this work was therefore to improve fine chalcopyrite recovery in the sulphide flotation circuit at Kansanshi, using a magnetic conditioning technology to agglomerate fine paramagnetic minerals. This theoretically increases the probability of attachment during collision and therefore improves recovery. A four-month paired ‘t’ test plant trial was carried out and comprised of consecutive ON-OFF periods with and without magnetic conditioning in the rougher flotation bank of the sulphide circuit. The experimental design involved assessment of recovery by size based on daily and weekly composite samples of feed and tails, sized using both wet-screening and cyclosizer. Both the daily plant data and the sized samples showed an increase in Cu recovery with magnetic conditioning ON. A 0.56% copper recovery improvement was measured with magnetic conditioning at a 99.4% confidence level. Keywords: Flotation, fine mineral, chalcopyrite, magnetic aggregation

Jan 1, 2020

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By J. C. Steinhobel

Answers to questions raised at the Symposium on Trackless Mining in Metal Mines Questions by J. O. Steinhobel (1) When rubber-tyred equipment is used for the delivery of stores and items of equipment, how is heavy material-pipes, rails, timber support, ventilation columns, etc.-dealt with? Termination of Membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register.

Jan 9, 1973

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) The position of converter blower at a side-blow Bessemer steel casting plant is vacant. The State Legislature of Utah has provided for the establishment of a metallurgical research department at the State School of Mines, Salt Lake City. Applications will be received for, the position of head of this laboratory, and further details may be obtained by applying to Prof. Joseph F. Merrill, Director, University of Utah, Salt Lake City. An engineering company owning patents for improvements in steel manufacture which have been adopted at many works in America, desires. to secure the services of a technical iron and steel metallurgist as assistant to its chief metallurgical engineer.

Jan 6, 1913

By A. L. Painting

A study of the end effects in specimen cores under compression tests, with a view to the elimination of these effects by A. L. PAINTING (Student) It is well known that a cylindrical rock specimen tested under uniaxial compression in conventional fashion is subject to end effects; that is, towards the end of the core, the stress and strain distribution becomes non-uniform. The experiment described illustrates such end effects with an aluminium core between steel platens. An attempt was then made to nullifythese effects by compressing the core between pads of mercury. The resulting stress and strain distribution was significantly more uniform, but a slight over-correction was introduced.

Jan 4, 1974

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By Louis A. Panek

This report deals with the combined friction and suspension effects in the reinforcement of horizontally bedded mine roof by bolting. Other reports have treated these two effects separately. Friction effect refers to the reduction of bending in a laminated roof due to the clamping action of tensioned bolts. If the beds tend to have unequal deflections, the bolts oppose this tendency, thus creating a suspension effect, which consists of a transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds within the bolted unit. The combined effects of friction and suspension on the bending of the beds, whether an increase or a decrease, are difficult to generalize because they depend on the bedding sequence and the bolt pre-tension. Some analysis of the bedding sequence usually is required to determine the critical bed within a set of bolted beds. However, if the suspension effect is substantial and if the bolts are pre-tensioned, then the greatest bending stress is likely to occur in the thickest bed. Findings are based partly on theory and partly on tests of mine-roof models in a centrifuge, which were found to verify the theory. Mathematical formulas are obtained for the change in maximum roof bending stress and for the change of roof deflection due to the combined friction and suspension effects. The maximum bending stress is needed for designing a roof-bolting system and the deflection for evaluating its effectiveness.

Jan 1, 1962

By Suresh K. Bhatt

Although overall worker productivity for U.S. underground coal mines is available, productivity by mining method and seam thickness is not. Mining technology has gone through dramatic changes in the past decade, and the industry has experienced a lack of accurate productivity Figures addressing these changes. This information is of great interest in planning for future mining systems as thick and shallow coal seams currently being mined are depleted and exploitation of thinner, deeper, and better quality seams is considered to partially meet the requirements of the 1990 Clean Air Act Amendments. In a cooperative program, the U.S. Bureau of Mines obtained raw mine level production and related data from U.S. Energy Information Administration for 1989 and 1990 and performed the needed statistical analysis. Base criteria, parameters, and salient results of the mine productivity analysis are presented in this report.

Jan 1, 1994

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By J. P. Beukes

The production of ferrochrome alloy from chromium bearing chromite ores is conducted at high temperature under highly reducing conditions. However, albeit completely unintended, it is impossible to completely exclude oxygen from all high temperature process steps, with the corresponding possibility arising for the generation of small amounts of Cr(VI) species. Certain Cr(VI) species are regarded as a carcinogenic, with specifically airborne exposure to these Cr(VI) species being associated with cancer of the respiratory system. With approximately three-quarters of the world?s viable chromite ore reserves located in South Africa, and annual ferrochrome production approaching almost half of total annual global output, aspects of Cr(VI) generation and control are of particular relevance and importance to the local industry, and naturally to the global industry at large. This paper seeks to examine theoretical and practical aspects associated with Cr(VI)generation (based largely on experience within the local South African industry, but considered to be generally encountered in the broader global industry context), together with mitigating measures that can be applied within the context of the production processes. From the discussions it is clear that significant improvements in various Cr(VI)-related aspects have been made by the South African ferrochrome industry. However, it is also evident that several areas of uncertainty still exist, which require further research in order to better quantify risks and enhance the efficacy of mitigating steps. Keywords Hexavalent chromium, Cr(VI), ferrochrome production, South Africa.

Jan 1, 2010

By A Struminski

The principles of occupational risk evaluation resulting from the improper ventilation of the underground mines were presented. It was shown that the risk level implies the appropriate planning and usage of prevention methods. That approach is fundamental in the ventilation, fire and climate safety management in the copper ore mines. The paper uses the adequately modified Risk Score method.

Jan 1, 2003

By William P. Diamond

Production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 m' to 10.1 x 106 m3. Peak production rates were generally about 0.03 to 0.06 x 106 &/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to several factors including: completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance, is hole location. Holes on the ends of the panels, where overburden strata are in tension due to the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location which is in compression. Analysis of gob gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1995

By W. G. Davenport

The offgas from flash furnaces inadvertently contains dust. The dust contains 25 to 30% Cu so it must be treated for Cu recovery. This is almost always done by recycling it back through the flash furnace*. This chapter shows how dust production/recycle is included in our matrix calculations. It then discusses the effects of dust production/recycle on flash furnace industrial oxygen and oil requirements. It concludes that re-smelting of dust requires considerable industrial oxygen and fuel, so that dust production should be minimized. Recycled dust also takes the place of new concentrate in the flash furnace feed system, decreasing Smelter productivity -another reason to minimize dust production. Compositions of industrial dusts are given in Appendix VII and Table 18.3. Industrial quantities are given in Tables 2.1, 3.1, 19.1,20.1' and Appendix VI.

Jan 1, 2001

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By Richards J. W.

J.W. RICHARDS, South Bethlehem, Pa. (communication to the Secretary?).-Mr. Howland's paper, data and conclusions have interested me intensely, and have led me to study carefully the record-of his 26 furnaces therein given. Mr. Howland is undoubtedly right in his conclusion that when expressing the amount of carbon burned at the tuyères in percentage of the total

Jan 1, 1917

By R. V. Ramani, R. Bhaskar

"While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mi ne environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use.As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined.The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.INTRODUCTIONThe sampling of airborne dust in mines can be done for several purposes. Traditionally, dust sampling has been restricted to the gravimetric measurement of airborne respirable dust to comply with the regulations governing the mining industry. Instruments such as the MRE gravimetric sampler, and personal gravimetric samplers that have collection characteristics similar to the human respiratory system have been in use for the last two decades. Presently available instrumentation for the purpose of regulation have been considered adequate by the Committee on the Measurement and Control of Respirable Dust in Mines (National Academy of Sciences, 1980),"

Jan 1, 1989