Search Documents

By Peter A. Hacquebard

Recent drilling programs have shown that the in-situ coal resources of Nova Scotia are very substantial. The grand totals of the measured, indicated and inferred categories amount to 232 m, 646m and 993 m tons, respectively. This vast quantity of coal occurs essentially in five main fields: Sydney, Mabou, Port Hood, Pictou and Springhill. The largest resources (84% of the total) occur in the submarine area of the Sydney coalfield. With a 65% recovery rate, there are at present 150m tons of proven, recoverable coal in Nova Scotia. At a predicted maximum annual production of 5 m tons, this amount equals a lifespan of 30 years. However, additional drilling, particularly in the Sydney offshore area, holds promise of increasing the recoverable reserve tonnage to at least 350 m tons. This figure may be compared with the 484 m tons production obtained during 191 years of mining (from 1785-1976). The geological appraisal of the remaining coal resources in the five fields mentioned is presented in three-dimensional diagrams, per individual seam and corresponding reserve area. In addition, the submarine extensions of the Sydney and Mabou coalfields are discussed in light of results obtained from off shore oil exploration wells. The terminology and standards of coal resource calculations are pointed out, and the phenomenon of seam splitting and its prediction from geological data is illustrated. The availability in Nova Scotia of either thermal or metallurgical coal is considered in relation to rank and sulphur content. This paper was presented in June 1977 at the 90th Annual Meeting of the Mining Society of Nova Scotia. The coal resource estimates, however, have been updated to include the results obtained with the offshore drilling in the Sydney Coalfield to November 1977.

Jan 1, 1979

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modelled with conditional simulation which generates multiple possible realisations of grade that are equally probable (or improbable) to occur. Methods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time consuming. This paper proposes a simple and efficient modelling approach to incorporating conditional simulation into pit optimisation, which would be able to be applied in currently commercially software. An example for Resolute Mining Ltd?s Syama Gold Project in Mali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Feb 27, 2013

By Om P. Garg

The purpose of this paper is: 1) To summarize the capabilities and some of the limitations of the existing mine planning software. 2) To provide some guidelines for acquiring the software. 3) To identify problems and challenges in terms of how to justify increased use of computers (particularly the 32-bit microprocessor based super micro computers), for various activities related to a mining operation No attempt has been made to review the contents of available software packages in detail. Also the scope of this paper is limited to mine planning related computer applications. Applications related to accounting, inventory control, preventive maintenance, equipment scheduling, etc. have not been covered.

Jan 1, 1983

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By T. R. Curr, W. A. Gericke, J. Basson

South Africa is a leading player in the international ferro alloys industry. Historical factors that have contributed to this dominant position include an abundance of natural resources and relatively low cost electricity. A number of relatively recent developments are potentially threatening this position. These include new legislation affecting the mining and minerals industry, a shortage of some types of suitable reductants, depletion of surplus electricity generation capacity with resultant threat of real escalation of electricity prices and pressure resulting from the recent strengthening of the South African Rand. The industry is addressing these challenges in a number of ways to ensure long-term viability. Some of these measures include investments in more efficient technologies that have economy of scale benefits and are less dependent on expensive reductants and electricity. Local macro-economic impacts include new legislation regarding ownership of enter-prises, mineral rights and royalties on mineral sales, development plans for port and rail infrastructure, as well as initiatives to expand electricity generation and coke production capacity. The fundamentals for being a successful ferro alloy producer are still largely in place for South African producers. Therefore the South African ferro alloy industry will remain competitive and is well placed for continued growth in line with the international growth in ferro alloy demand. The industry should emerge leaner, more efficient and ready to respond to any future demands of the industry. This paper will cover the present status of the industry, the factors that are impacting thereon and a view on its future outlook.

Jan 1, 2007

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By Kevin Bell

About Beltek Inc. For more than a decade Beltek, Inc. has been working with national and international organizations to harness and deliver solutions which gain real ebusiness advantages in today's world. Our objectives are to partner with our customers to achieve maximum results, while reducing costs. At Beltek, we provide a commitment to you and your organization's needs. Whether that be delivered by ensuring our services and products are state of the art or by providing a level of personalized service, which makes you feel like the center of attention, Beltek is about adding value to every job we work on. The individuals who work at Beltek quickly become your friends because we share your passion and enthusiasm for the business we are in. That's why every person is a leader in his or her respective fields. Having these individuals as apart of our business ensures you get the best out of our equipment, receive the very latest in advise, problem solving and support. We also pride ourselves on our ability to remain flexible at all times because we know deadlines and schedules can change quickly, so we always go the extra mile to deliver exactly what you need.

May 1, 2004

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969

By W. O. Henderson, H. W. Seaney

The sinking and grouting methods employed at the 3C and 3D ore hoisting shafts and the No. 5 service shaft are discussed. The reasons for selecting a circular section over a rectangular one and other technical aspects are reviewed.

Jan 1, 1974

By T Ireland, B Wright, S Weaver

All tunnels have unique characteristics that result in different fire and life safety risk. The fire safety systems for each tunnel also give different benefits at different costs. It is therefore neither pragmatic nor cost-effective to prescribe specific fire standards requirements for all tunnels. Each tunnel needs to be assessed individually but using a common process.The owner/client is normally the risk owner and needs to make the decision on what fire and life safety provisions will be provided within the tunnel. To make this decision they need to be appropriately informed. The low probability and high consequence nature of fire events creates a challenge such that traditional analysis processes, which tend to focus on a major event after it has happened, are not easily applied and do not give the best value for money. Therefore a process is required that provides the relevant information to the owner for decision-making.A quantitative risk assessment (QRA) provides a process and framework for the consideration of fire life safety risk when applied properly. This involves a risk assessment of the ‘do nothing’ option together with assessments of improvement options and their costs. It also involves consideration of benchmark safety levels for other tunnels and the open road.This paper will outline a QRA process for assessing fire and life safety risk in tunnels and how this has been used for three existing tunnels, Homer Tunnel, Lyttelton Tunnel and Mt Victoria Tunnel. Key challenges include determining an acceptable safety level, defining realistic inputs, providing sufficient complexity to get meaningful results but not so complex that transparency is lost and interpretation to enable decision-making by non-technical personnel.CITATION:Weaver, S, Wright, B and Ireland, T, 2014. A transparent and pragmatic quantitative risk assessment process for assessing fire safety in New Zealand tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 121–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Sebastian Avalos, Julian M. Ortiz, Willy Kracht

Semi-autogenous grinding mills play a critical role in the processing stage of many mining operations. They are also one of the most intensive energy consumers of the entire process. Current forecasting techniques of energy consumption base their inferences on feeding ore mineralogical features, SAG dimensions, and operational variables. Experts recognize their capabilities to provide adequate guidelines but also their lack of accuracy when real-time forecasting is desired. As an alternative, we propose the use of real-time operational variables (feed tonnage, bearing pressure, and spindle speed) to forecast the upcoming energy consumption via machine learning and deep learning techniques. Several predictive methods were studied: polynomial regression, k-nearest neighbor, support vector machine, multilayer perceptron, long short-term memory, and gated recurrent units. A step-by-step workflow on how to deal with real datasets, and how to find optimum models and final model selection is presented. In particular, recurrent neural networks achieved the best forecasting metrics in the energy consumption prediction task. The workflow has the potential of being extended to any other temporal and multivariate mineral processing datasets.

Jun 16, 2020

By G. Merazchiev

In the selection of copper ? molybdenum concentrates with the use of reagents containing sulfide ion ? sodium sulfide, sodium hydrosulfide etc for depression of copper minerals and pyrites, big part of depressor is oxidized by oxygen, which is dissolving in pulp during aeration with air in flotation machines and it is expended unproductively. This is the main reason for the big expenditures of depressor, reaching up 15~20 kg/t collective concentrate and the high exploitation expenditures for the copper ? molybdenum selection. Effective direction for lowering expenditure of depressor and increasing of the technical ? economical effectiveness of moly production is the conducting of the selection in nitrogen medium. In the paper are shown the results, obtained by applying of this direction in selection of collective copper ? molybdenum concentrate from the porphyry copper deposit ?Ellatzite? ? Bulgaria, in which the ratio Mo:Cu is over 1:120. In laboratory conditions, through comparative experiments in medium of air and nitrogen are defined: expenditure and initial concentration of NaHS in pulp for effective depression of copper minerals and pyrites; kinetics of flotation process of molybdenite; influence of pulp density; emf (negative milivolts) of pulp and the expenditure of nitrogen on tech-nological indexes of molybdenum flotation. When working in nitrogen medium decrease of NaHS in rougher molybdenum flotation from 40% to 45% is settled. When nitrogen is also fed in cleaner stages, the total expenditure of depressor is lowered by 64%. The quality of end molybdenum con-centrate is raised with over 5%. On the ground of the results of laboratory studies and of world practice data, an industrial installation for selection of copper ? molybdenum concentrate in nitrogen medium in Wemco inert ? gas machines.

Jan 1, 2014

Perhaps the most significant development in China's base metal sector is the discovery of major copper porphyries in northern Jiangxi Province and the adjacent southern Anhui Province. At the center of the new exciting district is the proposed Dexing copper complex, located some 350 km east of Nanchang, the provincial capital of Jiangxi. This project represents China's first attempt to put together a major large-scale open-pit operation, comparable in magnitude to Arizona porphyry operations. With the aid of Fluor Mining and Metals, the Chinese plan to develop a 135-175 kt/d open-pit mine, a matching large-scale mill, and the infrastructure needed to accommodate the big operations. An operation of this magnitude would significantly reduce China's import requirements by some 75%. China imports of the red metal are running around 200 kt/a. Under the direction of the Ministry of Metallurgical Industry, the Chinese are currently operating a 10-kt/d mine and mill with equipment primarily of Chinese origin. Dexing engineers told ME that they are considering a possible scale-up to 20 kt/d. How this effort will ultimately jell with the major expansion program is largely a matter of conjecture. Fluor Mining and Metals received a $10-million contract in December 1978 to develop a preliminary engineering and design program. While the original plans called for a 175-kt/d capacity complex, the Chinese subsequently decided to scale it down somewhat. The current proposal is around a 135 kt/d, which would in- elude the existing operation, according to Dexing engineers. Completion of the engineering and design phase is expected by March 1980 and a go-ahead decision will likely be made at that time. The value of the engineering and construction contract is estimated between $800 million and $1 billion. At right, mined ore is dumped 150 m down the mountain to a holding pocket below for rail haulage to the processing plant. Below, a Chinese miner tackles the universal problem of hard toes in the pit with a jack leg. Reserves and Early History The Dexing mineralization consists of three principal ore bodies, including the Chushahung on the north mountain, and the Tungchang and Fuchiawu on the south mountain. Combined ore reserves are estimated by mine geologists at 1.7 Gt of 0.4-0.5% copper. As is characteristic of porphyries, the ore contains important associated values of molybdenum, rhenium, pyrite, gold, and silver. There is also some secondary calcocite and bornite with an oxidized capping. Historically, copper was recovered with iron from the pregnant solutions emanating from the Tungchang deposit as early as the Tang Dynasty (700 AD). Modern day exploration was conducted by the Bureau of Geology in 1956 and reserve figures were es-

Jan 3, 1980

By C. G. Carlström

The total iron ore production in Sweden in 1969 was 33.3 million metric tons. 31.7 million tons were exported mainly to Western European countries. 27.8 million tons (87 per cent) originated from the mines at Kiruna, Svappavaara and Malmberget, located just north of the Arctic Circle in Sweden. Planned production for 1970 is 25 million tons during 10 months, due to a strike at the beginning of the year. Present production plans for the next five years expect an annual export capacity around 33 million tons in 1975, including 5.7 million tons of pellets. The mining and shipping at the loading terminals of Narvik on the Atlantic coast and Luleå at the Gulf of Bothnia are managed by LKAB - a 96 per cent state-owned company. 4 per cent of the share capital is owned by the private Grängesberg Company. The railway - 106 miles from Kiruna to Narvik and 130 miles from Malmberget to Luleå - is operated by the State Railways in Sweden and Norway. Comprehensive expansion of the Narvik ore port will be carried through during the next five years to increase the annual shipping capacity to at least 35 million tons and meet the development of rapidly growing ship sizes.

Jan 1, 1970

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979