Search Documents

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By W. Rostoker, R. F. Domagala, R. P. Elliott

The phase equilibria of the Hg-Th system over the composition range 0-100 pct Th and temperatures up to 1000°C have been studied for a small-volume, closed system. The solubility of Th in liquid Hg is about 5 pct at 300°C and decreases sharply with decreasing temperature. Two intermediate phases occur, Hg3 Th and HgTh. The structures of these are hexagonal (nonideally close-packed) and face-centered cubic, respectively. The HgTh phase decomposes eutectoidally at 400°-500°C. The solubility of Hg in solid thorium seems to be negligible. AFULL-phase diagram for this system would have to be defined on temperature-composition-pressure co-ordinates. This paper describes the pseudo phase diagram of a closed system, that is, where the alloy enclosed in a small volume equilibrates with a vapor pressure of mercury dictated by composition and temperature. Because of the experimental difficulties in studying a system of this nature, many of the phase relations can only be sketched. Alloy Preparation Alloys over the full range of composition were made from triple distilled mercury and one of two grades of thorium. For the bulk of the work, a calcium-reduced metal in sintered pellet form of reported 99+ pct total thorium content was used. Arc-melted specimens of this thorium gave a hardness of 135 VPN. The microstructure showed small primary dendrites of ThO2. A number of alloy compositions were made with a high-purity, iodide-decomposition thorium metal. The are-melted hardness of a button of this material was 35 VPN. Although the microstructure of the arc-melted specimens showed no dendrites of ThO2, there was definite evidence of an unidentified phase enveloping the grain bound-aries. There were no distinguishable differences between the constitution of alloys made with the two grades of thorium metal. Under normal conditions thorium is not wetted by liquid mercury. The film of ThO2 on all thorium metal cannot be penetrated by either liquid or vaporous mercury. It was therefore necessary to comminute thorium in the presence of mercury under such conditions that oxide films could not reform on the newly exposed metal surfaces. This was accomplished by the use of a high-speed, carbide-tipped rotary cutter incorporated in a chamber purged with argon and connected at the bottom to a demountable Vycor bulb containing a weighed amount of mercury. This experimental device is fully described in a separate paper.1 Alloy compositions were calculated by weighing the empty bulb, the bulb containing the mercury, and the bulb containing the mercury and the thorium chips. Many alloys were analyzed chemically for thorium and/or mercury after subsequent homogenization; the agreement between analyzed and calculated compositions was invariably very close. Bulbs containing the requisite amounts of mercury and fine thorium chips were clamped off, removed to a sealing unit, evacuated and sealed. Amalgamation under these conditions proceeded rapidly even at room temperature. To insure homogeneity, the specimens were annealed to 300-400°C. Alloys containing less than 30 pct Th remained pasty after all treatments, indicating an equilibrium condition of liquid plus solid. Alloys with more than 30 pct Th were transformed into a dark powdery product. These latter specimens were annealed for times of up to 1 week to complete interdiffusion. Many of the alloy compositions are pyrophoric. On exposure to air they oxidize with considerable evolution of heat to a mixture of ThO2 and free mercury. It was mandatory that alloy specimens be handled in a "dry box" purged thoroughly with argon. All X-ray diffraction specimens were powdered, screened, and sealed in capillary tubes within the dry box. Experimental Procedures Thermal analysis experiments, useful only in the mercury-rich region of the system, were conducted with the alloys in their original containers. A reentrant thermocouple well formed an integral part of the bulb. These bulbs were heated in a silicone oil bath and cooled in a dry ice-acetone mixture. The rates of heating and cooling were slowed by immersing the specimen bulb in a larger tube containing silicone oil. This provided a suitable thermal lag. In all tests, pure mercury was run as a basic standard. While the invariant reaction at about the melting point of mercury was detected by thermal analysis, the heat effect at the liquidus was not sufficient to produce an inflection in the cooling curve. It was necessary to determine the liquidus temperatures at the mercury-rich end of the system by "breaks" in electrical reslstivity versus temperature curves for individual alloys. The apparatus for this purpose consisted of a pyrex tube about 2 in. diam and 12 in

Jan 1, 1959

By Rolf R. Schillinger

It is established to an increased extent that the basic questions about raw material extractions deal with water, dust, noise and vibrations. If it has not been definitely proven that these points won?t lead to excessive environmental strains, attempts at any explanations will meet with disapproval in advance. In order to answer the basic questions about dust, noise and vibrations quality management becomes most important, particularly with respect partly unavoidable emissions of production processes. The specific questions have to be answered within the context of good blasting practices, latest discoveries of the explosives industry, and by use of a Blasting Works Quality- Management, which includes both production quality and Risk-Management. The paper shows a practical way to work out a Quality-Management Program for companies involved in blasting activities.

Jan 1, 2002

By John Stubbs

Sub-Surface Shaft excavation Mine development Headframes Surface Production facilities Product storage and loading Tailings area Infrastructure Discovery Lodge Utilities Operations complex Port Marine loading Rail unloading and storage

May 1, 2013

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By V. F. Marsters

THE main producing oilfields in Peru are located in the department of Piura and province of Thumbes, adjoining Ecuador on the south and west. In the department of Puno, a small field known as the Pirin or Hauncané Area was exploited some years ago by Fred Brown and associates and considerable production obtained. As. shown by the statistical table of production, this area reached its maximum production about 1909; since 1915, operations have been suspended. During the past year, however, the Peruvian Corpn. has acquired some interests in this section. It is reported to have made a few shallow tests with the hope of obtaining sufficient production to supply fuel for its railway lines, which operate between Mollendo on the coast and Puno and Cuzco in the interior. Only partial success has accompanied these efforts; nevertheless, exploitation is being continued. The petroleum of this region contains a paraffin base with small amounts of asphalt. While the gasoline content is small, the kerosene content runs as high as 30 per cent., with the fuel element varying from 50 to 72 per cent. While it is known that the structural conditions of the Huancané area are somewhat complicated, it is believed that exploitation based on a careful interpretation of the geology of the region will eventually yield commercial production of at least modest proportions. In the main fields in Piura and Tumbes, drilling operations were somewhat more active during the first half of the year, than in 1922. The latter half of the year witnessed curtailment, owing to the abnormal situation in the petroleum industry at that time. For the same reason, no attempt was made to obtain the maximum production from existing .wells. Production was pinched down and exportation of crude was correspondingly reduced during the latter half of 1923. Nevertheless, the total production of the Peruvian fields is considerably in excess of that for 1922, as is also the production of the Negritos area alone.

Jan 3, 1924

By P. Piga, O. Sammarco

There is a markedly increasing tendency to design deeper and deeper mines, to use larger amounts of explosive per round, to increase the advance rate of the excavations and so the natural ventilation tends to be more intense in the new mines. For this reason, the mines that make use of powerful mechanical ventilation should also take into account such factors as natural ventilation pressures, especially in the case of mines excavated in high-temperature rocks for which natural ventilation is particularly intense. The results of the studies reported here refer to a very hot mine excavated in an area with a high geothermal flow (the Boccheggiano - Campiano mine, southern Tuscany). At various external temperatures, experimental measurements and analyses have been made of the trend of the thermodynamic characteristics of the ventilation air and of the trends of the air/rock heat exchange along the downcast shaft and along the upcast shaft. These data were then used to work out approximate values of the corresponding natural ventilation pressures. After having identified the most conspicuous variations of the thermodynamic parameters of the ventilation air and the factors causing them, an assessment was made of the repercussions they have on the air flow rates and, above all, on the climatic conditions of the underground excavation sites. The natural ventilation pressures were found not to be constant in time; indeed they change continously and it is difficult to predict the changes. Moreover, it was found that their influence on the ventilation of a section of the mine network is greater if the effect of mechanical ventilation on that section is weaker. In the mine section where the measurements were carried out, some portions were found where the ventilation could become insufficient as a result of the effects of natural ventilation pressures. Finally, some guidelines to be followed in designing hot mines have been put forward which ensure efficient ventilation throughout the network at times with the aid of the natural ventilation pressures, which in certain circumstances may reach very high values in mines of this type.

Jan 1, 1987

By Alastair J. Sinclair, Asger Bentzen

Abstract - A simple linear model for interpreting duplicate analytical data for a range of values is described. The conceptual model can be quantified using a reduced major axis model rather than the inappropriate traditional least squares approach. The reduced major axis parameters (slope, intercept) and associated errors provide a quantitative basis for: (1) defining bias, and (2) comparing results within laboratories, between laboratories and between sampling/analytical methods. Application of the linear model must be preceded by extraction of obvious outliers or small groups of values that have an inordinately large impact on values of the statistical parameters defining the model. In addition, consideration must be directed to the presence of more than one population of sampling error, as in the case of multiple styles of mineralization being sampled.

Jan 1, 1998

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By J. R. Finlay

Every business man who has reached the age of forty, or perhaps even thirty, must know from his own experience that there are occasional periods of "good times'' and others of "bad times "-booms and panics. Those who give to business some complexion of science have invented a semiscientific name for these alternations-the business cycle-indicating that it is a normal phenomenon which by its own nature repeats itself. The longer one lives and the more one enlarges his own experience by the study of history, the more of these cycles he knows and the more disposed he becomes to take their recurrence for granted. If these alternations can be put into the category of common- places, why not treat them as such? We are in a sharp depression right now, why worry about it? Is there not a certain average value for business that can be depended upon in spite of depressions? By way of rejoinder one might answer that war is the great commonplace of history, but when we get into one we generally find it worthy of attention. In the present case, many a man has lost two-thirds of his income, and he is extremely nervous about finding it again. The Southern Pacific Railroad earnings have dropped 75 per cent in the past year; Pennsylvania, 60 per cent; United States Steel Corp., about the same. The drop in current earnings is

Jan 1, 1932

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

Currently the challenge that our society faces is to combine the economic activity for the continuously increasing needs of our expanding population with the necessary environmental integrity and the humanistic social concerns. In this paper, the methodologies that should be applied by the progressive mining industry in order to fall within the frame of the sustainable development are summarized. The Sappes project, an advanced gold mining project in north-eastern Greece, is presented together with the approaches adopted by Thrace Minerals S.A.

Jan 1, 2003

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By K. H. Coats

In tnany oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. This paper treats the problem of optimally locating the trunkline(s) for a given systet to nlinimize both the total length of piping connecting the individual wells or lease batteries to the trunkline and the length of the latter. Single and multiple trunklines, varying line sizes, and grouping of wells are considered. Some attention is paid to the case of a curved trunkline. A field case is treated and conclusions are that the problem of locating a single trunkline is relatively straightforward while the location of multiple trunklines requires further research. INTRODUCTION la many oil and gas fields, significant investments are required in piping networks for collection, injection and disposal of various fluids. A single field may concurrently require piping systems for gathering of oil, gathering of gas, injection of water or gas and disposal of salt water. Two problems arise in the consideration of any one of these networks. The first involves the sizing of the various segments of the network to minimize piping and compression costs. The second problem, treated herein, is that of optimally locating the trunkline(s) for a given piping system to minimize the total length of pipe connecting the individual wells or lease batteries to the trunkline. This minimization problem may arise in field automation if it involves replacement of individual lease batteries by a central field battery which will require trunklines and connecting pipelines to individual wells. The problem also arises in connecting a gas pipeline through a subsidiary trunkline to wells in a gas storage field. The first analysis given below treats the case of a single trunkline and of separate connecting lines for all field units.* The analysis is then extended to consider multiple trunklines and common connecting lines for groups of field units. Varying sizes, and therefore costs, of the connecting lines are taken into account. A simplified development is given to illustrate the manner in which line sizing calculations may be integrated with the line placement problem. This study is primarily directed toward the placement of straight trunklines, although for certain field shapes or well distributions curved trunk-lines might be preferable. Some mathematical consideration is therefore given to the placement of a curved trunk-line in a field. The determination of optimal locations for two or more trunklines involves some difficulties which are discussed below. The need for further research in this area is emphasized. The problem of a single trunkline is solved in relation to an actual oil field. The problem of optimally locating two trunklines in the same field is also treated and the results are compared to the single-trunkline case. All calculations reported were performed on an IBM 7072 digital compker. The importance of right-of-way, roads and terrain in locating trunklines and connecting lines is realized. The present analysis is advanced on the premise that in planning piping networks one should start with the optimal conditions whenever possible and proceed therefrom.

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By K. S. Choi, B. S. Shin

The adsorption characteristics of sodium silicate on scheelite, calcite, and fluorite minerals were investigated. Adsorption equilibrium took about 60 minutes. Adsorption data show that the masimum amounts of adsorption of sodium silicate occurs at about pH 9.8. The adsorptivity was in the order of calcite > fluorite > scheelite. The amount of adsorption of sodium silicate increased with the increase in temperature of sodium silicate solutions. The amount of adsorption of sodium silicate decreases in the low concentration range of ferrous sulfate, while in the high concentration range of ferrous sulfate, the adsorption of sodium silicate increases.

Jan 1, 1986

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

COMMITTEES. Precious and Base Metals. Charles W. Goodale, Chairman.. L. D. Ricketts, Vice-Chairman Darsie C. Bard, Secretary, Montana State School of Mines, Butte, Mont. Leonard S. Austin, Thomas J. Grier, Willet G. Miller, David W. Brunton, Hennen Jennings, Albert F. Schneider, Theodore B. Comstock, Edmund B. Kirby, George C. Stone, Stanley A. Easton, Charles W. Merrill, Benjamin B. Thayer. Samuel S. Fowler,

Jan 11, 1913

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012