Search Documents

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

"THE CONCEPT of energy as a commodity, while not entirely new, is not as widespread as the importance of the idea to this modern world would lead one to expect. The growth in the supply and use of energy over the past years has been tremendous, but our very closeness and familiarity have somewhat distorted the viewpoint, particularly of the younger generation. To many of us who remember the wonderful satisfaction of our first responsibility for directing two horsepower hitched to a farm cart or hay wagon, there still arises a feeling of some awe at the casual flick of the switch with which our sons and daughters summon to their convenience the service of some one hundred or more horsepower.Energy is the vital component of our existence and, no matter what contempt our day-to-day familiarity may •breed, it is wise to .pause from time to time and consider our national energy standing. Have we still capital in the bank? Are our expenditures wisely •conceived and well directed? Is provision being made for the years •ahead for the needs of our children and our children's children?"

Jan 1, 1953

By J. R. Giegerich

Purpose It is the purpose of this paper to describe the application of underground conveyor systems to the transportation of ore in the Sullivan mine of The Consolidated Mining and Smelting Company of "Canada, Limited, at Kimberley, British Columbia. General Applications Conveying has been recognized as a means of underground transportation for a great number of years but only during the past fifteen to twenty years has there been any extended application of the method to underground metal-mine operations. Coal miners became conveyor conscious before metal miners. Probably one reason for this is the fact that there are more flat coal seams than flat orebodies. A second reason is that coal is light and is a less abrasive material than most metallic ores. The vast improvements made in belt construction during the past few years, together with improvements in mechanical conveyor equipment, have gone a long way in making this form of transportation attractive to the metal miner. In new mines being opened today, or in major extensions to older mines, the possibilities of conveyor transportation should receive serious consideration. There may not be any widespread application of the belt conveyor as a replacement for the conventional hoisting and locomotive haulage. Where there is an application, tl1e saving in cost can be appreciable and many operating ad-vantages gained because of ease in operation.

Jan 1, 1951

By Tom Snyder, John Brulia

"The U. S. commercial explosives industry annually transports thousands of tons of hazardous materials (HM) in the form of explosives, oxidizers, and combustible liquids by highway in truck-tractor/trailer combinations and straight trucks, including pickups. Managing risk during transportation is every commercial explosives industry motor carrier’s number one job."

Jan 1, 2014

By I. Iwasaki, R. Titi-Manyaka

Chlorination and chloridization behaviors of pyrite, pyrrhotite, marcasite, chalcocite, covellite, galena, sphalerite, heazlewoodite, and elemental sulfur were investigated by thermogravimetric analysis. The possible reaction mechanisms are discussed on the basis of the theoretical weight changes and thermodynamic considerations. Chlorine is a more effective chloridizing agent than hydrogen chloride. In the light of the experimental results, a scheme for producing nonferrous metal chlorides, molten sulfur, and ferric oxide from complex sulfide flotation concentrates is discussed.

Jan 1, 1974

By S D. Fox, P B. Swart

Statistics showing that mine rehabilitation is falling behind rates of disturbance continue to be reported in the media. Unfortunately, most reported statistics do not account for the large growth-cycle that mining in Australia experiences, where there are typically significant new disturbances with large portions of these areas not being available for rehabilitation for a number of years. Many commentators assert that better planning is required to ensure that rehabilitation will be able to achieve a safe, stable, non-polluting landform that meets the agreed post-mining landuse.This paper focusses on the revegetation aspects of mine rehabilitation and in particular the matters that need to be addressed in the planning stage so that revegetation success is ultimately able to be demonstrated to regulators and other stakeholders.CITATION:Fox, S D and Swart, P B, 2018. Planning revegetation for relinquishment, in Proceedings Life-of-Mine 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By F. B. Plummer

THE practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania. oil fields30.? It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcite has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a new district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content: of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written con-cerning experimental work on the actual effect, of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores29, have developed a method of investigating the results of acid treatment which has enabled

Jan 1, 1935

A number of mineral deposits occur in close proximity to the Pacific plate fronts. Among these deposits are gold-silver and the base metal sulphide deposits of copper, zinc and lead. Gold deposits that commonly occur in these areas are of hydrothermal origin. Of these the epithermal deposits have attracted the attention of the exploration geologists as well as the metallurgists. One vital aspect of the activity of the geologists is the development of models for epithermal gold mineralisation in the Pacific Rim. These models can also be used by metallurgists for predicting gold extraction processes. This paper reviews the mineralogy, fineness and the host minerals of gold and examines the data in the light of gold mineralisation in the southwest Pacific Rim. The gold mineralisation models proposed for the Pacific Rim have been used to predict gold extraction processes suitable for the various mineralisation types. Discussed also are the mineralisation and treatment processes of some selected epithermal gold deposits and gold-rich porphyry copper deposits in Indonesia, Papua New Guinea, Solomon Islands, Fiji and New Zealand.

Jan 1, 1999

By M. Mohammadijoo, J. B. Wiskel, D. G. Ivey, S. Kenny, H. Henein

Cold-wire tandem submerged arc welding (CWTSAW) has recently been developed as a novel welding technique to replace the conventional tandem submerged arc welding (TSAW) process and improve the productivity of pipeline manufacturing. The process involves two electrodes with arcs and one electrically cold electrode. Since heat-input of the welding process is a key factor affecting the properties of the weld metal (WM) and the heat-affected zone (HAZ), and the additional cold-wire affects the heat introduced to the weldment, it is of interest to investigate property and geometry changes in the WM and HAZ when a cold-wire is added to the welding process. In the current research, the CWTSAW process is investigated and optimized by correlating the main welding parameters with the micro-hardness of the WM and HAZ and the geometry of the weld, i.e., the bead width (BW), penetration depth (PD), reinforcement area (RA) and coarse grained heat-affected zone (CGHAZ) area. Three statistical and mathematical methods are employed to optimize the CWTSAW process in terms of the mechanical properties and WM and HAZ geometry of a typical microalloyed steel used for pipeline manufacturing.

Jan 1, 2015

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By R. L. Roller

In recent years, there have been many articles and papers written on the use of specially designed belt conveyor systems in mining operations, either economic studies or actual experience. These papers generally conclude that the use of these systems can reduce overall costs from 10% to 40% over conventional methods using general purpose equipment (truck/shovel, scrapers, etc.). However, they also generally conclude that conveyor systems are inflexible and capital intensive. With the increasing cost of mobile equipment, the capital cost conclusion is losing steam, particularly when the costs of maintenance shops, road and ramp construction and other related start-up costs are thrown in. Attention here will be focused on answers to flexibility related questions, but first, a look at costs in general. Basic production economics tell us that when we have a small job to do, it is cost effective to use simple, low cost, general purpose tools which will have a minimum impact on total cost. It also tells us that when we have a large project, we can employ methods using special, relatively expensive production tools. Figure 1 illustrates what occurs on projects, of different sizes, with various quantities of production. With small quantities of work, the cost per unit of work starts out much lower using general purpose equipment, rather than using special purpose methods and equipment. However, at a relatively low quantity of work, the cost hits a lower limit and, regardless of how great the quantity of work, the unit cost can never go any lower.

Jan 1, 1985

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

The object of crushing and grinding for leaching is obviously to permit contact of the solvent and mineral and subsequent removal of pregnant solution in a reasonable time. Heap leaching is the leaching of ores that have been mined and transported to prepared, relatively impervious pads for leaching by sprinkling or ponding, and percolation of the lixiviate through the ore. Dump leaching is the leaching of dumps or low-grade ore or overburden without the use of prepared pads under them. Run-of-mine material, e. g., low -grade ore from open pit stripping operations, may be leached without crushing, and a fairly high recovery made by heap leaching. An alternate method for better grade gold/silver ores is to crush to 9 to 13 mm (318 to112 in. ) size for pad heap leaching, as used by Smoky Valley Mining Company at Round Mountain, Nevada, on gold ore, and to 38 rnrn (1 -1 12 in.), which will be done by Candelaria Partners, at Candelaria, Nevada, on silver ore. Heap leaching of copper probably began at Rio Tinto, Spain, about the year 1752. This was done by the leaching of weathering piles of ore in the open air followed by iron cementation of the liquor that drained off the heaps. Its application to the low -grade southwestern United States copper ores was overlooked for many years, and low- grade ores from Sacramento Hill at Bisbee, Arizona, were the first to be heap leached in 1923. Site preparation used a half century ago is the same today. "The need for some form of waterproofing of the pad was evident. Before leaching ore was piled, the site was cleared of cactus and brush. After clearing a gentle sloping area, it was then covered with a blanket of rolled and tamped clay or slime tailing. When heaps are built, a layer of coarse fragments may be put down first to assist drainage. A second method of leaching without grinding, usually for higher grade ores, is by vat or tank leaching of material crushed to 9 to 13 mm (318 to 112 in.) size. Such a plant is considerably more expensive than a heap leaching installation but much less costly than grinding for agitation leaching, and a recovery higher than that obtained by heap leaching is to be expected. Vat leaching has been widely used by the copper industry on higher grade copper ores but has been used in only a few small operations on that size gold or silver ores. However, such a plant should be considered for a modest tonnage of a few million tons, 3 to 7 g per mt (0.10 to 0.20 oz per st), of Carlin-type leachable ores crushed to 9 mm (318 in.).

Jan 1, 1981

By W. E. C. A. B. Eustis

(Read at the Philadelphia Meeting, February, 1878.) IN September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the following terms : "The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1878

By A. Ivanova

The continental shelves occupy a vast area of Russia and contain complexes of commercial placer minerals. Of prime importance are Cenozoic placers of valuable minerals including gold, cassiterite, diamonds, chromite, platinoids, and minerals of titanium, zirconium and rare earth elements, biogenic amber and fossil ivory (1). Commercial placer minerals are associated with shelf placer formation zones (SPFZ). These zones are located at junctions of marginal orogens and shelf troughs in morphostructures where upwarping, subsidence, and sign-variable neotectonic movements are not significant. The SPFZs are characterized by ancient buried leveling planes with mantles of waste, series of wave-cut aggradation terraces on land and beneath the sea, and drowned and buried stream valleys. The occurrence of mineral placers in the SPFZs was caused by endogenic mineralization and exogenic placer hosted formation. Concentrations of commercial biogenic minerals are associated with areas of burial of biogenic material (release of resins by plants and theriofauna thanatocoenoses) and with their transition zones. Since the Oligocene, alternations in marine transgression-regression have dominated the shelf areas. This has resulted in the formation of polygenic placers. Climatic conditions are of great importance: warm and humid climate in the Paleogene-Neogene changed to colder climates in the late Pliocene (polar type sedimentation; formation of permafrost strata and sea glaciation). These events are responsible for the regularity in placer formation during the Cenozoic in which the early Cenozoic (Eocene-Oligocene-Miocene) and late Cenozoic (late Pliocene-early Pleistocene and late Pleistocene-Holocene) epochs are prominent.

Jan 1, 2004

By Edwin H. Bentzen, Immo H. Redeker

Important industrial minerals are separated and concentrated by froth flotation by industry today. The following descriptions are presented as an overview of the methods employed to separate and recover a few of these industrial minerals. The minerals described in this section of the book are not, by any means, the only important minerals treated by froth flotation. Other minerals, such as calcite, kaolin, wollastonite, rare earths and vermiculite were not included, primarily due to the confidential nature of the information held by the Minerals Research Laboratory and the Colorado School of Mines Research Institute. Flotation of nonmetallic minerals is sometimes viewed as alchemy. However, the art is, in reality, based on sound chemistry, experience and a little luck in the treatment of new ores. In the flotation of nonmetallic minerals, as opposed to base metal sulfides, highly specific treatment conditions are required to accomplish separations. The presentation of the treatment of each of the minerals described was outlined as follows: DEPOSITS PROCESSING SPECIFICATIONS FLOWSHEETS (in some cases) A presentation of the factors, often critical, which must be carefully investigated to accomplish successful flotation of nonmetallic minerals is presented in the section on Sulfonate Collectors, elsewhere in this volume.

Jan 1, 1986

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

By Richard Hurteau

Design and validation of an integrated guidance system for articulated ground vehicles is investigated. The development of an autonomous industrial vehicle must take into the account the specific geometry of these vehicles; they can be composed of a tractor with 1 or 2 trailers or of articulated type like LHD. Moreover the tractor-trailers type vehicles can have on-axle hitch configuration or positive/negative off axle configuration. The path-tracking of a tractor-trailer vehicle in restricted space is presented and discussed in this paper. Recent results obtained in simulation and validated by experimentation are also presented. These studies can lead to better ways of maneuvering an articulated vehicle in a restricted space or automatically executing of docking and parking maneuvers

May 1, 2002