Search Documents

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Nobuyuki Okamoto

The present three-year long phase of the SOPAC/Japan Deep Sea Co-operative Mineral Resources Programme [Programme], commenced in 2000. The Programme has been funded by the Government of Japan through the Japan International Co-operation Agency (JICA) and the Metal Mining Agency of Japan (MMAJ), since 1985. Field survey activities and associated data analysis and interpretation, for the Programme, has largely been carried out by the Deep Ocean Resources Development Co., Ltd. (DORD). The Government of Japan has, since 1982, recognised DORD as one of its ? Pioneer Investigators? for manganese nodules in the Clarion Clipperton Fracture Zone . Although the objective of this paper is to present the results of the drilling cruise that was conducted from December 2001 to January 2002, within the North Fiji Basin, in Fiji?s EEZ, it will also seek to provide a broad overview of the results of the cruise conducted within the Cook Islands in May to June 2000, as well as present preliminary results of the cruise conducted in the Marshall Islands in June to July 2002.

Jan 1, 2002

By L. Figueroa

Electrochemical methods have potential to treat waters impacted by mining, while simultaneously producing a recoverable metal product to off-set treatment costs. Mining-impacted waters may present challenges with electrochemical treatment due to low concentrations and complex solutions of numerous dissolved metals. This paper presents an evaluation of the potential strengths and limitations of abiotic electrowinning of mining-impacted waters. In particular the impacts of chemical composition on metals removal are evaluated. Results of bench-scale experiments demonstrate the potential to remove metals on the cathode (copper, cadmium, lead), as well as the anode (manganese). Pre-treatment for iron and aluminum may be needed and post-treatment pH adjustment would be necessary. INTRODUCTION Due to continually increasing demand for metals, new technologies and innovative applications of existing technologies are needed to recover metals from mining-impacted waters. Electrochemical methods have long been used for metallurgical processes with solutions containing high concentrations of the target metal. However, electrochemistry also has potential to treat waters with lower metal concentrations, while simultaneously producing a recoverable metal product to offset treatment costs. Electrochemical water treatment may have several benefits over traditional alkaline treatment for acid rock drainage (ARD). Sludge produced from alkaline treatment has high water content that is difficult to dewater, even for treatment plants producing a relatively high-density sludge. For example, the Argo Tunnel Water Treatment Facility (Argo Facility) in Idaho Springs, Colorado uses hydrated lime to produce a high-density sludge with a solids content of 20 to 25 percent and filter cake with solids content from 30 to 35 percent [1]. Furthermore, costs for managing the sludge are significant, approximately $90,000 per year for treating approximately 150 million gallons of water [1]. Although not the case for the Argo Facility, sludge produced from alkaline treatment of ARD has potential to be classified as hazardous. Disposal of sludge also opens up the potential for future liability depending on the sludge’s chemical stability and methods of disposal. In contrast to alkaline treatment, electrochemical treatment produces metals in elemental and other highly-dense forms on the cathode. If metals concentrations and flow rates are sufficiently high, the metals recovered may help offset overall treatment costs. In addition, sludge production would be reduced, if not eliminated altogether, thereby reducing both disposal costs and potential future liabilities as well.

Jan 1, 2019

By J. Leslie Goodier

The International Law of the Continental Shelf, so far ratified by 35 nations, extends the national boundary of any coastal nation to the edge of the continental shelf, this normally being at a continuous water depth of 200 m. The Law further extends this boundary to include the floor of the deep ocean to any depth that can be mined by advanced mining technology. In effect, proof of mining can constitute proof of ownership of the subaqueous land and the minerals on or below the sea floor. Irrespective of the fact that present technology is too limited to permit mineral exploitation in the high seas-and the law regarding the right to mine appears hazy-the U. S. Treasury Department's Bureau of Customs, has a ruling that would further deter mining operations on the high seas. This law contends that minerals mined on the continental shelf of the United States are actually mined within the continental United States and are free of tariff, but mined products or other articles obtained from the ocean or the sea floor beyond the continental shelf, if brought into this nation, must be considered as imported and are subject to such customs duties as are applicable under the tariff schedules of the United States.

Jan 7, 1968

By D Misra, R Ganguli, S Bandopadhyay

The objective of this paper is to assess the accuracy and applicability of recent state-of-art methods such as the machine learning algorithms (MLA) for mineral resource estimation. Conventional methods such as geostatistics have been predominantly used in the mining industry for this purpose with varying success. Recent advances in the use of MLA have provided a fresh approach to obtain improved accuracy in the estimation of mineral resources. Two MLA methods: the neural network (NN) and the support vector machine (SVM) have been used to estimate a polymetallic ore deposit in Alaska.The general characteristic of SVM and NN emphasises the fact that they can approximate any multivariate non-linear relation among variables. Although neural network models are able to capture the nonlinear spatial relationships that may be present in the data, they are usually difficult to optimise under sparse data settings. Of the various NN alternatives, despite their effectiveness, the model selection and estimation process is typically difficult as it involves solving complex integration and optimisation of parameters. In support vector modelling (SVM), estimating of parameters involves optimisation of a convex cost function. The working principle of SVM makes it robust against noisy and extreme value data. At the same time, it can capture the spatial distribution of ore grade more effectively with careful modelling and selection of SVM parameters.The outcome of the MLA methods were compared to those of the geostatistical ordinary kriging (OK) application to study their generalisation ability. The comparison was made using the following goodness of fit criteria: mean-squared error; mean absolute error; mean error; and coefficient of determination. The results indicated that the MLA methods may improve the predictability of ore deposits and thereby reduce the inherent risk in mineral resource estimation.

Sep 26, 2011

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By T. M. Jones

This paper outlines the development of the theory of controlled district recirculation and indicates the advances in understanding and technology which have enabled a major change in established ventilation practice. An insight is presented into the possible future use of controlled district recirculation as acceptable practice in mine ventilation planning.

Jan 1, 1987

By S. K. V. Avasarala

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading tests and installation of over 3,300 prestressed concrete piles for a building complex consisting of 12, 5- and 6-story over parking buildings. The project was recently completed in three-phases over a span of 4 years. The subsoil conditions were explored by performing 25, Standard Penetration Test (SPT) borings throughout the site. Various types of driven pile foundations were considered and following an evaluation of high structural loads and site-specific constraints such as variable depth of bearing layer of Florida limestone and quality of clay and limestone layers, a prestressed concrete pile support system was selected as the most economical and effective foundation approach. The building foundations were designed for a pile capacity of 353 kN (40 tons) in compression, 45 kN (5 tons) in lateral capacity for a deflection of 0.64 cm (0.25 in.), and 133 kN (15 tons) in uplift capacity. The axial and lateral allowable pile capacity and lengths were predicted using SPT91 and LPILE computer programs, which are generally used in Florida. The validation of these capacities was derived from 144 probe piles and performance of 12 pile loading tests on selected probe piles. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the loading tests on probe piles. This information was effectively utilized as part of the overall quality control program to install a total of 4,186 prestressed concrete piles (including 144 probe piles) in different building areas across the project site to depths ranging from 8 to 21 m (25 to 90 ft) below existing ground elevation as part of foundation support system. This engineered, monitored, and tested foundation solution provided an effective and satisfactory basis for completion and approval of the foundation work for this 12, 5- and 6-story over parking building complex. A recent reconnaissance has indicated that all the building foundations are performing satisfactorily.

Jan 1, 1995

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. The following question has been suggested for discussion: "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein.† Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line? In some multivein districts the line for any given vein may be approximated by simple interpolation or extrapolation. Where this is possiblc the bottoms of the lowest ore shoots in the various veins are points on an imaginary, gently rolling surface. The trace of this surface upon the vein is our critical line for that vein. The imaginary surface rolls so gently that it may be projected from two or more known veins to an unexplored vein near by. Here is a criterion for the bottoming of ore that has nothing to do with changes in the appearance of the vein in question; it rests solely on the depth at which the ore bottomed in adjacent veins. The method is not applicable in districts only slightly explored in depth, nor where the lower limit of the ore-bearing horizons

Jan 1, 1941

By Gerald A. Munson, Fremont F. Clarke

DURING recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodu-mene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S. Lithium Corp. of America, during its rapid development and growth, has successfully employed three different methods of concentration: 1) hand sorting, 2) Heavy Media separation, and 3) froth flotation. Each method, though economic in its sphere, is becoming outdated as extractive techniques improve. The most recent development has taken place at Lithium Corp.'s new operation in North Carolina, where the extractive process yields lithium compounds directly from mined rock without an intervening concentrating step. Until 1954 Lithium Corp. mined only in the southern part of the Black Hills of South Dakota, where the various types of lithium-bearing pegmatite could be used to develop untried processes of beneficiation. Concentrates from these operations are shipped to the corporation's chemical plant in St. Louis Park, Minn., where actual extraction of lithium and production of commercial compounds takes place. Nature of Deposits The geology of the southern Black Hills pegmatite deposits is admirably presented by a U. S. Geological Survey publication.' Only the factors pertinent to exploitation need be mentioned here. Lithium Corp. has been interested primarily in three deposits, the Edison, the Mateen, and the Longview-Beecher No. 2. The history of these deposits dates back to the mining boom of 1880 to 1900 in the Black Hills, when most of the deposits were prospected for tin by the ill-fated Harney Peak Tin Mining Co. The three deposits described here, however, lay idle and unwanted until Lithium Corp. opened the Edison mine in 1943 and the Mateen and Longview-Beecher No. 2 in 1951. Edison Deposit: The Edison deposit is about a mile southeast of Keystone, S. D., on the northeastern flank of the Harney Peak uplift. The deposit consists of no less than four and probably at least six separate pegmatites that coalesce in a central mass from which the individual pegmatites finger outward and downward in complexly folded schist and gneiss beds of the country rock.

Jan 1, 1956

By Carolyn Barnes

The Offshore Technology Conference, the world's largest technical conference and exhibition on the development of offshore resources and protection of the ocean environment, is sponsored annually in Houston, Texas, by 12 international engineering and scientific societies. This year's OTC, the seventh, will be held May 5-8 at the Astrodomain, and will be the largest in its history. The technical program for the first meeting in 1969 consisted of 100 papers, an exhibit display of 380 booths, and an attendance of 4300. This year. 280 technical papers are to be presented, and more than 2800 exhibit booths, representing some 1200 companies and nine countries, will be on display for an anticipated audience of 40,000.

Jan 4, 1975

JoHN W. BELL, Montreal, Quebec, Canada (communication to the Secretary*).-Mr. Taggart's reply illuminates a puzzling element in his original paper. Unconsciously, he has allowed practical considerations to influence some of his conclusions. In certain cases, he accepts the direct conclusions indicated by his Stadler efficiencies, and these are proved wrong by both the Rittinger and practical method for estimating efficiency. In other cases, a direct conclusion based on his Stadler figures would be so unsatisfactory to him, that he is. compelled to argue how he could have obtained satisfactory results if lie had crone something that

Jan 10, 1917

By T. F. Witherbee

IN a paper read at the Lake Superior meeting, August, 1880, an account was given of the successful use of Rendrock and Monaky powder upon a scaffoldn and salamander in the furnace. On April 5th, 1881, the same trouble called for like treatment, which, though not so immediately. successful, was on the whole more instructive than the first trial, and points, I trust, to a reasonably sure remedy for all such difficulties. Up to December 4th, 1880, foundry and mill iron were made from Old Bed and New Bed magnetite, and Kearneyy red hematite, when a return was made to Bessemer iron, from an inferior quality of New Bed ore as compared with that used during first blast. January 18th, 1881, New Bed, Chateangay, and East-shaft, a newly-opened Bessemer deposit of Messrs. Witherbee, Sherman & Co., were first used, and continued up to February 13th, on a fuel charge of 80 per cent. anthracite and 20 per cent. coke, the product on the three ores being about 10 tons more per day than on New Bed alone. From this time until March 11th all coal was used, and New Bed, Chateangay, and East-shaft ores, up to February 22d, and from that date Chateangay and New Bed, the product falling off 9 6/10 tons per day as a result of not using coke. It is fair, however, to state that the furnace was not in good condition during' this period, being over-burdened, and the New Bed ore was, temporarily, uncommonly poor, for reasons of no particular interest here.. It required to properly flux it at least 140 per cent. of limestone; and 101 per cent was actually used. March 11th, all Chateangay ore and 80

Jan 1, 1882

Jan 1, 1969

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.' The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.' The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00' were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-'. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By M. H. Cullender

The performance characteristics 01 gas wells producing from formations which fail to stabilize within a relatively short period of time are obscured by the interrelation of the coefficient (C) and the slope "n" of the conventional back-pressure curve q = C(P2 f- p2s)n An empirical method is presented whereby the characteristic or true slope (11) of the back-pressure curve may be determined for a particular gas well. For those gas wells which do not stabilize within a relatively short period of time, the coefficient (C) is considered as a variable with respect to time and as a constant only with respect to a specific time. Thus, the back-presrure performance of such a well is presented as a series of parallel curve5, each curve representing the performance of the well at the end of a given time interval. Through use of the method presented, a simple presture gradient is developed and maintained within the drainage area around a producing gas well during the test period in order that the variation of the coefficient (C) with respect to time does not obscure the true value of the lope. INTRODUCTION The back-pressure method of testing gas wells as set forth by Schellhardt and Rawlins1 is dependent upon the requirement that a series of flow rates and corresponding pressure data be obtained under stabilized conditions. These data arc then plotted on logarithmic coordinates of flow rate (Q) vs difference in squared pressures (P2f — P2s) in order to determine the constants (C) and (n) for Equation 1. With respect to this method of presenting the performance characteristics of a gas well, it should be pointed out that although Equation 1 is an empirical relationship, the form of the equation was justified to a considerable extent by an independent development by Muskat and Botset.2 This development was theoretical in nature; however, certain assumptions with respect to the type of flow existing (viscous vs non-viscous) were madc which may or may not be correct. As the use of the method presented by Schellhardt and Rawlins spread through the industry, it became evident that the method of testing was applicable for those wells which approached stabilized prbducing conditions within a relatively short period of time. Performance characteristics could not be determined by this method, however, for wells which approached stabilized protlucing conditions slowly over a considerable period of time. This characteristic of "slow stabilization" has generally been associated with gas wells producing frorn reservoirs of low permeability. As the demand for natural gas continued to grow through the years, a great number of wells were completed in reservoirs of low permeability which exhibited "slow stabiliz:~tion" characteristics. Consequently, the problem of determining the true performancc characteristics of these wells became more apparent. It is with this problem in mind that the isochronal performance method of determining the flow characteristics of gas wells is presented.

Jan 1, 1956

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By R. L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps is a potentially hazardous practice which often results in localized slope failures. A limit plasticity approach to determine the total admissible weight for moving loads near slope crests is presented. A three-dimensional analysis provides an upper bound solution to the load that can be applied to the top of the slope (dump point), and it also provides the critical distances of the load from the slope crests. The analysis accounts for the inertial forces generated by the deceleration of a moving load (e.g., a dump truck), and it also includes the drag resistance of the front wheels if the brakes are engaged. The results can be utilized to determine the safe operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism. An example with realistic parameters also will be presented.

Jan 1, 1991