Search Documents

By Yotamu Stephen Rainford Hara

"The aim of our work is to investigate a low energy and clean route for the recovery of copper and cobalt from complex sulphide mineral concentrates. The mineral concentrates were roasted in air, in the presence of CaO (MS + CaO + 202 =MO+ CaS04) at temperatures below 973K. The roasted products containing CuO, CoO and Fe203 were carbothermically reduced at 1073K within an hour to preferentially reduce copper and cobalt. The kinetics of reactions were studied using the thermogravimetric technique and by characterisation ofreaction products using the XRDSEM-EDX techniques. The effects of MS:CaO ratio, roasting temperatures and physical nature of the mineral concentrates were analysed. The method for capturing S02 by forming CaS04 was analysed for reuse in the process. The energy balance for the above process is compared with that of conventional continuous smelting/converting process.1.0 IntroductionCopper sulphide mineral concentrates from Zambia contains substantial amouot of cobalt. The cobalt metal content in the concentrates ranges between 0.7 and 2 % weight, which corresponds to 3 and 9 % weight copper, based on the spot price of copper ($7 386/tone) and cobalt ($31 000/tone). Although the traditional approach using a combination of roasting-leaching-electrowining steps can be applied to recover copper and cobalt from sulphide mineral concentrates [1-4], there are two major draw backs of the traditional process: (i) the S02 emitted during roasting is too lean for economical conversion for sulphuric acid manufacture, which causes serious environmental pollution. (ii) silver and gold which are normally present in the sulphide concentrates are lost out [5] because they are not leachable by H2S04 or HCl which are the common leachants. The above two problems have been overcome by adopting flash smelting in which a rich S02 gas above 20% is produced [1, 5] and successfully converted into sulphuric acid. The precious metals tend to partition to blister copper and recovered during refming. However, nearly all cobalt is lost into the slag phase uoder oxidising condition which prevails during flash smelting. It is important to note that the cobalt content in the slag can be up to 2.6 % weight [6]. The recovery of cobalt from the slag is a process which requires huge amouot of energy since the slag is smelted above 1873K [6]. With a view of minimising the amouot of energy and S02 emission during metal recovery, our investigation involves roasting the sulphide concentrates in the presence of lime and reducing the roasted samples with carbon."

Jan 1, 2013

By S. Kesler

Rössing Uranium Limited has operated since 1976 a large open pit uranium mine and extraction plant at a remote site in the Namib desert, South West Africa/Namibia. The geology (Berning, I., et al. Economy Geology) and the technical aspects concerning mining, grade control and metallurgy have previously been described (Rössing Uranium, Mining Magazin and Whyllie, R.J.M. "Rössing Uranium reaches rated production", World Mining). The improvement of leach 'extraction has been reported in 1984 (Kesler, S.B. et. al. "Uranium extraction at Rössing") and the installation of a central process control system has been described (Kesler, S.B. et al. "The introduction of a central process system at Rössing"). At the beginning of 1983 a decision was made to develop a computer system for metallurgical plant optimisation which included mass and volumetric balances, analytical assays for up to 5 chemical elements and the costs for the major consumables. Within 10 months this computer system was developed and implemented. A large number of test runs were made and computer studies were undertaken. The metallurgical division now has a scientific tool for production; planning for actual comparison with plant results and for strategic investigations and decision making.

Jan 1, 1986

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By F. M. Lewis, E. C. Johnson

Used as a classifier in a plant expanding capacity or changing to closed-circuit operation, the liquid-solid cyclone offers the advantage of being adaptable to existing conditions. This paper presents the costs involved and experience gained from operating a unit of this kind. BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid-solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made. The unit installed is a 24-in. diam cyclone classifier with a 20" cone angle. Diameter of the vortex finder is 8 in., the feed entrance area 20 sq. in. Maximum diameter of the adjustable apex valve is 6 in. and minimum diameter approximately 3.5 in. To refer again to Figs. 1 and 2, the cyclone* is mounted motor. It is charged with 18 tons of 1-in. balls. The overflow, or fines, passes by gravity directly to the copper flotation plant. The ball mill discharge and the new feed combine in a sump from which they are sent to the cone by an 8x6 SRL pump at a rate of 497 gpm. Pressure at the cyclone is 5 psi. For reasons dictated by the nature of the ore treated, particularly the bonding of fine grains of chalcopyrite to pyrrhotite, the froth from the second cell of the copper rougher circuit is returned to the regrind mill. This flow, which somewhat complicates the standard closed-circuit calculation, is seen in Fig. 1 to be 156 tpd of solids. This combines with the cyclone classifier underflow to constitute the ball mill feed. The requirement of the regrind product is that it be 77 to 80 pct —200 mesh. The liquid-solids cyclone operating in conjunction with the 6x12-ft mill adequately met this requirement. Of primary importance is the fact that this arrangement provided sufficient classification capacity to replace the undersized classifier and was capable of building up a circulating load to 87 pct, large enough to give an efficient grind. In this instance the circulating load is taken as the ratio of sands to new feed. Any comparison of performance between this liquid-solid cyclone and the replaced classifier would of course be unfair, since the bowl classifier was

Jan 1, 1955

By B. Denby, R. Hollands, S. Cooper

Augmented Reality (AR) is a technology that can be used to mix computer-generated images of data with views of the real world. The University of Nottingham is developing AR technology in a major research project which can be used to assist mining companies in visualising complex mine data whilst out in the field. The technology comprises of integrated GPS surveying technology and electronic orientation devices to provide location and viewing information, video capture via digital camera and portable computing hardware to overlay 3D models on views of the real world. The paper describes the concepts of the technology in some detail and concentrates on the possible applications of this in the surface mining and exploration industries.

Jan 1, 2002

Foreword—H. Foster Bain........................ 7 Officers and Committees......................... 9 PAPERS Growth of Metallic Crystals. By C. H. Desch...............13 Aluminum Castings of High Strength. By R. S. Archer and Zay .Teffries (With Discussion).............................35 Constitution of Alloys of Aluminum, Zinc and Tin and Aluminum, Zinc and Cadmium. By V. Jares.......................65 Exudations on Brass and Bronze. By W. B. Price and A. J. Phillips (With Discussion)..................•..........80 Preparation of Metallic Single Crystals and Twinning in Zinc and Zinc Single Crystals. By 0. E. Romig (With Discussion).............90 Plastic Deformation of a Zinc Single Crystal. By S. L. Hoyt (With Discussion) 116 Plastic Deformation of Coarse-grained Zinc. By C. H. Mathewson and A. J. Phillips (With Discussion)......................143 The Solidus Line in the Lead-antimony System. By E. E. Schumacher and F. C. Nix (With Discussion)........................195 Note on the Distribution of Energy in Worked Metals and the Effect of Process Annealing Temperature on the Final Annealing Temperature of Fine Copper Wire. By L. Zickrick and R. S. Dean (With Discussion)........207 Note on the Relation of Annealing Temperature to Conductivity of Copper Wire. Ry J. C. Bradley (With Discussion)..................210 Beryllium-copper Alloys. By W. H. Bassett (With Discussion)........218 Some Comparative Properties of Tough Pitch and Phosphorized Copper. By W. R. Webster, J. L. Christie and R. S. Pratt (With Discussion).....233 A Study of the 470" C. Transition Point in Cast 60:40 Brass. By Frances Hurd Clark (With Discussion).......................253 Strldy of the Heat Treatment, Microstructure and Hardness of 60:40 Brass. By Frances Hurd Clark (With Discussion)...............276 Corrosion and Physical Properties of Some Alloys of Aluminurn, Zinc and Tin. By N. 0. Taylor (With Discussion)..................302 Equilibrium Relations in Al-Mn Alloys of High Purity. By E. H. Dix, Jr., and W. D. Iieith (With Discussion)....................315 Deformation of an Aluminum Alloy by a Constant Load. By C. B. Sadtler and J. L. Gregg (With Discussion)....................336 Still Casting of Metals. By P. H. G. Durville (With Discussion).......343

Jan 1, 1927

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By N. A. Gokcen

In this Bureau of Mines report, appropriate equations correlating the activity of water with the activities of electrolytes in binary and multicomponent solutions have been derived for computer calculation. It was found that the half-integer power series are far superior to the integer power series, for both types of series having the same number of terms. The pro-posed method of calculation is capable of accurately yielding the activities of all components from the measurements of the activity of a single component at various concentrations. This method replaces the cumbersome and objection-able method of graphical integration of the Gibbs-Duhem equation. Two novel methods are proposed for determination of activities of electrolyte solutions important in hydrometallurgy; (1) Water vapor pressure measurement by differential pressure transducers having an accuracy of 0.001 pet, and (2) transpiration method with an inert gas bubbled through concentrated solutions followed by the analysis of the evaporated and redissolved electrolytes with specific ion electrodes having a sensitivity of ±10-10 molal. The first method is suitable for nonvolatile electrolytes, and the second, for volatile electrolytes such as hydrogen halides, HN03, H2S03, etc. The existing methods of estimation of ionic activities have been surveyed, and the best method has been selected, discussed, and summarized.

Jan 1, 1979

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By A. Refahi

For predicting the energy consumption during the size-reduction process, the Bond approach is often used. In this work, the PFC3D discrete element method (DEM) software was employed to model the crushing behaviour of some rocks with different mechanical properties in a laboratory jaw crusher. FLAC3D software was adopted to analyze the stress distribution in the rocks. The rocks studied were modelled as granular assemblies in the shape of a sphere and/or a cube located between two jaws, and the work done by the jaws in the crusher was determined. Nine different types of rocks were studied and the energies consumed by the crusher were compared to those of the Bond comminution energy estimated from the Bond index. There is considerable difference between Bond crushing energy and work done by the jaw crusher for rocks. It appears that the Bond approach is not a suitable method for predicting single particle fracture energy done by the crusher. To verify the results obtained from DEM models, the fracture behaviour of the crushed rocks was examined and was compared to the PFC3D results. The tensile mode of fracturing is favourably modelled by the PFC3D software while the delamination mode cannot be well modelled by PFC3D software. Keywords: jaw crusher; discrete element method; crushing energy; Bond index

Jan 1, 2009

By P. Somasundaran

Adsorption of a nonionic polyacrylamide (PAM), an anionic polyacrylamide with sulfonate functional groups (PAMS), and a cationic polyacrylamide with amine functional groups (PAMD), on hematite was investigated as a function of different solution conditions. Adsorption results indicate that the major mechanisms of adsorption of polyacrylamides on hematite is through hydrogen bonding, with electrostatic forces playing a secondary role. All the polymers exhibited irreversibility of adsorption upon dilution. Also, entropic effects were determined to be important in adsorption. Surface chemical properties of hematite and solution chemistry of the polyacrylamides are considered to explain the polymer adsorption behavior on hematite.

Jan 1, 1985

By Konstantinos Theodoridis, Michael Galetakis, Olga Kouridou

Recent advances in Artificial Neural Networks (ANN) and Adaptive Neuro-Fuzzy Inference Systems (ANFIS) have provided a new approach to the estimation of related quality characteristics, such as heating value, ash content and moisture of coals used for power generation. The basic strategy for developing ANN and ANFIS models for the prediction of missing quality values, is to train the models using an existing quality data set and an appropriate learning method. Statistical analysis results of the estimated values, showed that ANN and ANFIS are not only more accurate than the widely used regression models, but also tends to reproduce the variability of the initial data, while regression models generate a smooth representation of reality.

Jan 1, 2002

By Filigenzi M. T

Stresses around mine openings at depth can cause the surrounding rock to fail, releasing stored strain energy. When this happens, the rock may literally explode or `burst' into the opening without warning. As mining progresses deeper into the earth, the possibility of seismic events and rock bursts increases. Researchers at the US Bureau of Mines (USBM) are currently studying seismic activity in three underground hard-rock mines in the United States: the Homestake Mine, Lead, SD; the Lucky Friday Mine, Mullan, ID; and the Sunshine Mine, Kellogg, ID. Waveforms from seismic events are recorded by personal-computer-based hardware and software. This information is archived and transferred from the mine sites to the USBM via modem communication links. Then, using USBM-developed software, the events are analysed to determine various parameters, including magnitude, frequency, and location. In addition, researchers are modelling the deep levels of the Homestake Mine using a finite-element code. These models generate stress and displacement values for a given loading condition. By studying material properties, in situ stresses, and seismic activity along with actual scope sequencing, researchers can make correlations between stresses induced by mining and the frequency and magnitude of seismic events. Information on seismic events coupled with results from finite-element analyses have increased understanding of rock mass behavior and the mechanisms that may lead to rock bursts. Optimisation of slope sequencing designs as a result of these studies could reduce rock burst hazards.

Jan 1, 1995

By E. C. Harder

INTRODUCTION THE situation in the United States, at the present time, regarding the supply of manganese ores and alloys of manganese is one of great seriousness and is likely to become increasingly so while the European war continues. The two principal iron-manganese alloys, ferromanganese and spiegeleisen, are indispensable in steel manufacture, being used extensively in the Bessemer and openhearth processes.. Spiegeleisen, the lower alloy, contains between 15 and 25 per cent., and ferromanganese, the higher alloy, between 60 and 80 per cent., of manganese. Besides manganese the alloys contain iron and carbon. On the market ferromanganese is usually quoted on the basis of 80 per cent. manganese, and spiegeleisen on the basis of 20 per cent. manganese. The consumption of ferromanganese has been increasing during recent years at the expense of spiegeleisen, because larger quantities of the latter must be used to ac-complish the same purpose with the result that the amount of carbon introduced with it into the molten metal is frequently injuriously great. Manganese ore proper, in the form of manganese dioxide, is used extensively in many chemical industries, especially for oxidizing purposes. It is also used for the manufacture of both wet and dry electric cells and in the manufacture of paints and dyes. The manganese ore used in this country has been derived hitherto from three principal sources:. Southern Russia, Southern British India and East Central Brazil. The following tables show the quantity of manganese ore imported from these countries, and (for comparison) the domestic production, during 1912, 1913 and 1914. The imported manganese ore has been used largely in the manufacture of iron-manganese alloys and in addition large quantities of the alloys themselves have been imported, chiefly. from Great Britain, Germany and other European countries.

Jan 5, 1916

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By J. C. Hampton, L. A. Matzar, C. R. Gamwell

In geomechanics, conducting uniaxial or triaxial compression tests require samples to be prepared to a certain length-to-diameter ratio. This ratio is typically defined as 2:1 (length to diameter) and is accepted as a common standard for all materials on which mechanical properties testing is performed. Variations in sample length can cause changes in measured strength properties across multiple material types, such as cement, rock, or soil. Within the oil and gas industry, it is not uncommon to receive samples for technical services work that are slightly under or exactly the length requirement before surface grinding and sample preparation. Many of these samples are discarded from uniaxial and triaxial compression tests and used in another manner; therefore, it is necessary to study the length-to-diameter ratio in efforts to understand the limits and validity of testing samples that are slightly out of the 2:1 ratio. This paper discusses uniaxial compression tests performed using Berea sandstone and a standard cement mixture of 2.54-cm diameter to study changes in rock strength and properties. Compressive strength for each lengthto- diameter ratio over a range of 0.5:1 to 2.2:1 was measured. The investigation was extended to study near-end effects, where the sample length is near, but not exactly twice the diameter. It was discovered that the cement samples conformed reasonably well to the suggested ASTM correction factors. The sandstone did not conform to the correction factors and further analysis is required to develop a correction factor unique to the material. Near end effects, in both the cement and Berea, were found to increase compressive strengths, especially when the L/D of the samples was increased slightly over a 2:1 L/D.

Jan 1, 2015