Search Documents

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By M. H. Kotze, V. Yahorava

A gold-selective ion exchange resin, containing tributylamine groups, was developed by Mintek for the recovery of gold from cyanide leach solutions. The Dow Chemical Company and, more recently, Purolite commercialized the production of this gold selective resin for use in the gold mining industry, and it is marketed as Dow XZ-91419.00 and Purolite A194 respectively. A novel application of this resin is the selective recovery and separation of AuCl4 - f rom p latinum group metals (PGMs) in chloride and nitrate solutions. The current paper describes potential benefits of this type of resin for selective recovery and upgrading of gold from low grade chloride or nitrate waste streams, and the possibility of gold separation from PGMs during their refining in chloride media.

Jan 1, 2014

By Mark Gershon

This paper describes an application of a new approach to mine planning and production scheduling in a gold mine. The technique, limited to use in open pit mines (but not limited to gold), has been described previously (Gershon, 1987). The-computer program used is the HOPS software, which has been described previously as well (Gershon, 1988). The mine is scheduled for the production of 8,000 blocks out of a mine having 25,000 blocks (50 x 50 x 10). The technique is based on the concept of inverted cones (Gershon, 1987). While it does not provide a true optimization of results, it does approximate the optimal situation. As opposed to most scheduling software that only serves as a computerized notepad for the scheduler, the use of this approach allows for a scheduling intelligence to be built into the software.

Jan 1, 1989

By J J. Pretorius, G M. Hoffmann

Utilisation of lower-grade (<60 per cent Fe) resources, not utilised in the current products, is crucial to ensure optimal resource utilisation and maintaining/improving future profit margins by reclassifying low-grade material to ore. The purpose of the Sishen Expansion Project (?SEP?) is therefore to investigate the technical and financial viability of producing up to an additional 10 Mtpa of new products at Sishen from material currently classified as low-grade materials. Jigging technology has progressed to a point where Sishen?s 50 to 60 per cent Fe run of mine (?ROM?) material, once considered as waste, can be beneficiated to produce a saleable 64 per cent Fe product. This has been confirmed through appropriate beneficiation testwork. Consequently, Sishen can now produce saleable product from material not currently included in the resource definition, increasing the resource base of the mine significantly and ensuring higher resource utilisation. Mine Planning utilised the geological models to produce detail planning schedules, reflecting the current and SEP plants separately, optimised to comply with product specifications of both the current and SEP plants and to confirm the viability of the low-grade resources identified as SEP feed material. The SEP products specifications have been derived by optimally matching iron ore market requirements with the revised resource base. A 64.0 per cent Fe lump product and a 63.5 per cent Fe fine product are the optimal SEP products. The SEP plant will be able to produce 10Mtpa at an average yield of 60 per cent and a lump to fine ratio of 62 to 38. The plant consists of five major sections namely crushing, material preparation, beneficiation, final product handling and quality control services. Maximum integration with the current Sishen plant was considered. Kumba currently has an agreement with Transnet to rail up to 23.5 Mtpa through the Sishen Saldanha Iron Ore Export Channel (?IOEC?). Transnet and Sishen Iron Ore Company have signed a Definitive Agreement that deals with the expansion of IOEC?s capacity, which increases Kumba?s entitlement from 23.5Mtpa to 35.0Mtpa. The detailed enviro-legal impact assessments for the SEP indicated that the project has low enviro-legal risk as a result of it being a brownfields project incorporated into the current Sishen operations.

Jan 1, 2006

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.&apos; The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953

The objective of current efforts by AQUILA Mining Systems Ltd. is the continued development of computer-based systems and techniques to automatically process and interpret monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1995

By V. Rajaram, S. Bhattacharya, M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, (in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory a field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30% to 65% less in reverse than when operating in the normal forward mode.

Jan 8, 1983

By A. F. Baker, E. R. Palowitch, A. W. Deurbrouck

As air-pollution regulations become increasingly more stringent, increased significance is being placed on the amount of sulfur present in coals used for steam generation. These regulations are aimed at minimizing the pollution of the atmosphere with noxious gases such as the sulfur oxides that are formed and emitted when coal is burned. Two meet these future requirements, a definite need exists to reduce the sulfur content of some of the coals used for steam generation. Reducing pyritic sulfur involves liberating the pyrite from the coal and then removing it. The specific gravity of pyrite is high (5.0) compared to that of coal (about 1.2, mineral-free), and standard coal-washing devices, such as wet concentrating tables, will efficiently remove pyrite particles larger than about 100 mesh. Particles below this size will be entrained in the table water and will be carried into the clean coal product. Techniques such as froth flotation are of little benefit for pyrite reduction because the flotation characteristics of pyrite are similar to those of coal.

Jan 6, 1966

By S. Kawatra, K. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from fines migration. Agglomeration of the ore can immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it “feels right”. We have developed procedures to quantitatively determine whether a binder gives good performance in an acidic solution, and have identified several binders that will be suitable for copper heap leaching.

Jan 1, 2007

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By Michelle Cardinale Souza Silva Macedo

Neste trabalho, o comportamento eletroquímico das ligas Ti-35Nb-xTa (x = 0; 2,5; 5,0; 7,5)Ta (% em peso), solubilizadas e resfriadas em água, foi investigado em meio de NaCl a 0,9% mol/L através de testes de polarização anódica e medidas de impedância, micrografias e DRX. Os ensaios eletroquímicos mostraram que as ligas contendo tântalo apresentam uma maior resistência à corrosão que a liga sem tântalo. Além disso, os ensaios eletroquímicos em conjunto com as micrografias e DRX indicam que a composição Ti-35Nb-5Ta é a que apresenta maior resistência à corrosão no meio estudado, pois além de ocorrer uma estabilização da fase ?, o refino do grão foi menos pronunciado e por esse motivo minimizou o surgimento de microcélulas eletroquímicas.

Aug 16, 2017

By K. Hawboldt, J. E. Halfyard, C. Bottaro

The removal of sulfur from leach residues has been practised in the zinc industry using a combination of flotation and hot melt filtration. The process is highly dependent on the nature of the concentrate and the subsequent residue. When the mineral constituency of the residue alters, the process can encounter significant operational challenges. An alternate method of converting elemental sulfur to water-soluble polysulfides was applied to leach residue from Vale&apos;s nickel demonstration plant in Argentia, Newfoundland. Reaction parameters, sulfur purity and other key indicators are discussed as is the potential commercial application.

Jan 1, 2011

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By F. H. Edmunds

LLOYDMINSTER is the centre of a well developed agricultural area, lying on the Alberta-Saskatchewan interprovincial boundary in Township Fifty. The surrounding country is gently undulating, without any notable topographic features, but twenty-two miles to the north the North Saskatchewan river, and thirty miles to the south the Battle river, have cut deep valleys. In the spring of 1934, a wild-cat well (Lloydminster Gas Company&apos;s No. 1 well) was successful in striking a large flow of gas at a depth o 1,974 ? feet. The gas was piped into the town, a short distance south, and Lloyd-minster became the first Saskatchewan town to be served with natural gas. Following this discovery, other wells were sunk and, up to the present, thirteen wells have been drilled m what is here designated the Lloydminster area. Ten of these wells are in Saskatchewan and three in Alberta. Seven were successful in obtaining gas, three oil, and three have been unsuccessful. The area tested by this drilling is about eight thousand acres, six thousand of which can be considered as proved gas or oil land. To the south and west of Lloydminster, in the Province of Alberta, there are several areas in which oil and gas have been discovered. The Wainwright field lies nearly fifty miles to the southwest; Battleview, where recently gas has been discovered, is thirty miles west-southwest; and the Ribstone area is about thirty miles south and a little west. At Ribstone, a number of wells were drilled some years ago and there is a small production of oil. The data relating to the wells in the Lloydminster area that are recorded in this paper are taken from the records of the several companies operating in the field. The names of these companies are given on the map and on the type stratigraphic section (Figures 1 and 2). The author wishes to record his appreciation to Mr. R. H. Shaw and Mr. 0. C. Yates, both of Lloyd-minster, for much valuable information; also to Mr. E. Swain, of the Department of Natural Resources, Regina, with whom the writer has visited the field on several occasions, and who, by his enthusiasm and encouragement, has done much to forward the development of the area. The well samples were examined at Ottawa by officers of the Borings Division of the Geological Survey of Canada, who also made the interpretations of the logs. Frequent references will be made to the work of Dr. G. S. Hume, of the Geological Survey, and the writer would like to pay tribute here to his work.

Jan 1, 1940

By William A. Johnson, Robert F. Mehl

It is now recognized that several important types of reactions in metallic systems proceed by the formation of nuclei and the growth of these nuclei. The process of freezing is a simple example of this, as Tammann pointed out years ago.1 Tammann held that the rate of freezing is determined by a rate of nucleation, expressed as the number of nuclei formed per unit volume of unfrozen liquid per second, and a rate of growth of these nuclei, expressed as the linear rate of radial growth in units of length per second. For isothermal freezing the conception is simple; for ordinary freezing, extending over a range of temperature, it is not as simple, for the values of the two constants must change with change in temperature. There is ample evidence that the postulated mechanism is correct even though a quantitative derivation of the rate of isothermal or of ordinary freezing in terms of the two constants has been lacking. In recent years other reactions have been found to proceed in a similar fashion. It has been well established, particularly by Bain12-8 that the formation of pearlite from the eutectoid decomposition of the solid solution austenite proceeds in such a way, and Polanyi and Schmid, Tammann and Crone, Karnop and Sachs, and others9-11 have shown that the process of recrystallization proceeds in a similar way. Isothermal reaction rates have been determined for eutectoid decomposition by a number of investigators. Bain&apos;s2-8 work on the formation of pearlite from austenite is especially valuable in this respect—the type of isothermal reaction curve obtained, as illustrated in Fig. 13, showed an initial slow rate, accelerating to an intermediate maximum rate which then decelerated to the completion of the reaction; similar curves have been obtained by Wever and his collaborators.12 Other eutectoid decompositions show similar behavior: for example, the decomposition of the beta eutectoid in the copper-aluminum system, studied by Smith

Jan 1, 1939