Search Documents

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983

By N. Chow

The recovery of manganese from lower-grade resources has been studied for a number of years. Of key importance in prior work was the discovery that higher-valent manganese can be readily leached with sulfurous acid. This eliminates the need for high-temperature reduction roasting that is conventionally used in processing high-grade material. High-temperature roasting is energy intensive, emits a large amount of carbon dioxide and would not be economical for processing lower grade material. While the prior work provides important information for extracting manganese from lower-grade resources, the production of unwanted byproducts and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems that to this point have precluded commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low-cost, environmentally friendly manner. The emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted byproducts.

Feb 1, 2012

By Dale Ross, Bill Clements, Jim Spanos

Current world conditions are forcing the search for "green" energy technology in every aspect of our daily lives. Finding alternatives to petroleum fuels seems to be at the top of the list. The search for the "perfect" alternative is something like the never ending quest of the perpetual motion machine. Unfortunately, the laws of physics prevent us from getting something for nothing, and Murphy's Law normally gives us nothing for a lot of something. Regardless of Murphy, the quest goes on, and in our industry cheaper ANFO seems to be the popular subject.

Jan 1, 2012

By Oliver R

The Hamersley Iron ore resources are geologically complex with fluctuations in mineral chemistry. From this resource Hamersley Iron must produce consistently high quality direct shipping products and have the ability to evaluate the effects of changes in demand. In order to achieve these objectives an incremental long term planning technique has been developed. This method reduces the total geological resource statement into a simple, logical sequence of events. A logical sequence of mining increments is defined within individual areas based on a final pit and access system. Increment characteristics are derived manually and from a computer based orebody model. The end product of the technique, an optimum mining schedule, is readily developed from the incremental information. Among its many benefits, this simple technique rapidly provides management with information for policy formulation.

Jan 1, 1979

By Yaw Boadi, Andrew McCallum, Sandy Gray, Yavuz Atasoy, Peter Wemyss

"Various full-scale test programs and installations of the InLine Pressure Jig (IPJ) have provided evidence that pre-concentration of the difficult to leach sulphide mineral through gravity can provide significant increases in economic recoveries. The continuous gravity concentrates are intensively treated either by re-grinding or Intensive Cyanidation. Data from various mine sites worldwide is presented. Treatment of complex ore bodies with this low cost methodology may render previously uneconomic ore bodies financially viable and assist in the recovery profile of transitional ore.INTRODUCTIONThe use of gravity is made extremely attractive in complex ore situations due to the low cost of operation, typically a few cents per ton operating cost and lack of chemicals.Gold mines which suffer from poor recovery due to complex mineralogy such as Stibnite, Arsenic, Carbon, Telluride, Silver and other pacifying agents such as Iron, which can form coatings, can all benefit from the process proposed in this paper. The key issue is not overall recovery as much as one of economic recovery. The key to this is maximised recovery at the lowest possible capital and operating cost. Other options such as flotation are reviewed but are not seen in many instances to be the panacea due to issues discussed in the paper. The use of the InLine Pressure Jig in the re-circulating load of the milling circuit is a cost effective means of recovering a sulphide/gold concentrate containing the complex mineral assemblages which require re-grinding and intensive leaching for optimised gold recovery.The benefits of Jig Assisted Grinding (JAG) are many and the challenge over the past years has been developing, understanding, implementing and evaluating the benefits of various flowsheet models. This has involved the reconciliation of results in plant scale trials back to the original laboratory test program. The following paper outlines the insights gained in this area through extensive work carried out by many people across both laboratories and plant sites in Australia and overseas. The examples in this paper are some of the work carried out on a few selected sites but similar work has been carried out on other sites such as Penjom, Granny Smith and Agnew. This work has eventuated in several installations which we believe have great importance in the future of the gold processing industry. They will lead the way forward to the modern all-gravity plants of the future.Compared to flotation, for the recovery of sulphides, gravity is a simple option. The simplicity generally translates to low capital and operating cost."

Jan 1, 2004

By H R. Pein

"The Corridor Sands deposit is situated approximately 190 km north east of Maputo, Mozambique adjacent to the paleo-mouth of the Limpopo River. This deposit is one of the worldÆs largest known economically viable resource of titanium, accounting for approximately one third of the global resource. As part of the pre-feasibility and feasibility study for development of the Corridor Sands project, various geological and geotechnical investigations were undertaken, selected results of which are presented in this paper. These investigations have enabled a detailed understanding of the material characteristics of the orebody as well as the tailings materials, such as the fines, to be developed. These material characteristics have had a significant impact on the selection of the mining and disposal methods currently being implemented."

Jan 1, 2001

This paper provides a review of the chemical reactions occurring in the submerged arc processing of chromite ores. The excavations of industrial furnaces have shown that the charge, as it descends through the furnace, passes through a number of distinct reaction zones. Each zone is characterised by differing process conditions and reaction products. The phase equilibria, reaction steps and mechanisms occurring as the charge progresses through the furnace are examined, and the potential influences of these factors on the process outcomes are discussed.

Jan 1, 2004

ANNUAL MEETING OF THE NEW YORK SECTION - The annual meeting of the New York Section was held at the Machinery Club, May 7. While the dinner, at which fifty attended, was in progress, the names of the nominees for next year's officers were posted. The result of the election was as follows: Chairman, E. P. Mathewson; vice-chairmen, William Y. Westervelt, R. M. Atwater, Jr.; treasurer, Wilber Judson; executive committeemen, Lucius W. Mayer, Edwin S. Berry. The subject for the evening was "Organization and Campaign in France of the 27th Engineers." Colonel O. B. Perry described the many difficulties surmounted, for it was necessary to work with untrained men ALLEN H. ROGERS WALTER S. DICKSON CHAIRMAN OF NEW YORK SECTION SECRETARY OF NEW YORK SECTION and shortage in supplies. He described the unusually fine character and physique of his officers, which made it possible to make the untrained men most efficient. He described in some detail the work of building bridges over the Meuse River and the bringing up of supplies to the first army base, in particular at the Argonne-Meuse sector; General Pershing gave a personal commendation of the work undertaken by this regiment. The Colonel described the methods of operating the transportation of ammunition and supplies to the "army dumps," by which at the time of signing the armistice there had been brought up 600,000 tons of equipment for use in the projected campaigns. An interesting item was that 3,600,000 sand bags had been provided, in case the Germans should be able to turn the line of the American troops. Captain Edwin S. Berry described the methods of sending materials to the front lines and gave figures to indicate the huge quantities required, adding that the order of preference was troops, ammunition, food, and engineers' supplies. The speakers then answered several questions given by the members present. WALTER S. DICKSON, Secretary.

Jan 6, 1919

By G. A. Doyle

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1997

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Anthony Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Jan 1, 2004

By Paul A. Bailly

“For innovative leadership in bringing about a quantitative rationality to mineral exploration; for the impact his efforts and wide respect have made on national mineral policy issues; for his effective managerial role in major mineral discoveries; and for his lecture, ‘Managing for Ore Discoveries.’”

Jan 1, 1980

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Rolf Koenig

A fire aboard a vessel transporting explosives and detonators manufactured by Dynamit Nobel endangered the cargo. Due to the special safety properties of the detonators, no mass detonation occurred.

Jan 1, 1989

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By N. Ohmura, H. Saiki, T. Nagaoka

A microbiological flotation system that facilitates the removal of pyritic sulfurfrom coal is reported. The chemoautotrophic bacterium Thiobacillus ferrooxidans is utilized as a pyrite-selective biological surfactant that augments the flotation-mediated rejection of pyritic sulfur. The bacteria were produced by continuous cultivation in 50-L tanks, where it was possible to produce 3.8 x 1012 cells/day when the dilution rate was optimal and the pH was 1.6, a condition that prevented ferric precipitation. Prior to flotation, the bacteria were mixed with coal, which allowed cells to selectively adhere to the pyrite. The adherence of bacteria made the pyrite surfaces more hydrophilic, which facilitated separation by increasing the tendency of pyrite to sink, while the hydrophobic coal floated. When a synthetic coal/pyrite mixture (10.1 % sulfur) was subjected to microbial flotation, the level of sulfur rejection was stable during the entire period of operation (i.e., one hour). In the absence of bacteria, flotation reduced the sulfur content of a coal/pyrite mixture to within the range of 6.7% to 7.4%, with the combustible recoveries ranging from 93.9% to 99.0%. In the presence of bacteria, the sulfur content of cleaned coal was in the range of 1.3% to 1.4%, with the combustible recoveries ranging from 80.8% to 86.3%. Bacterial activity accounted for 57% of the total sulfur rejected through flotation. The desulfurization capacity of the system was further confirmed by testing it with run-of-mine coal. The pyritic sulfur content was reduced from 2.9% in the feed coal to around 1.2% in the froth product, while 80% of the combustible recovery was retained. Microbial flotation removed 60% of the pyritic sulfur from the feed. These findings demonstrated that micro¬bial flotation could be utilized for the removal of pyritic sulfur from coal in a semicontinuous system.

Jan 1, 2000

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By Hendrix J. L, Nelson J. H

A model based on non-steady state has been developed for dissolution and diffusion in porous ore particles. Results from the particular model have been incorporated, as a rate term, into a global, heap-scale model based on a plug flow reactor at unsteady state. The global model can be used to consider leaching by aqueous-phase reagents in equilibrium with a gas- phase component, such as oxygen gas, as well as strictly aqueous-phase reagents, such as cyanide. The flexibility of the model even allows predic- tion of the outcomes of using reagent sideflow injection in large heaps. Data from column leaching tests are compared to the model, and their relationship is discussed.

Jan 1, 1991

By H. C. Doepken

Wrought Hadfield steel was tested in axial tension at from 100° to —196°C, to determine flow and fracture stresses as well as conventional properties. Ductility and related properties, such as fracture stress, decreased continuously with temperature. Peculiarities during straining indicated possible martensite formation or mechanical twinning. THE mechanical properties of austenitic manganese steel have been summarized by Avery and Day,' including the low temperature tensile properties reported by Hadfield and coworkers2,3 " These data show the material to be brittle at both liquid oxygen and liquid 'hydrogen temperatures. Avery and Day report considerable ductility measured by Charpy V-notch tests at —100°F (-73°C). Since the review of low temperature properties by Seigle and Brick' show face-centered cubic structures, other than Hadfield steel, to be ductile at low temperatures, it was felt that a study of tensile properties, between the reported intervals, should show whether the decrease in ductility was a gradual decline or an abrupt drop beginning at some intermediate point. X-ray examinations were made in an attempt to shed further light on the mechanism of work hardening of austenitic manganese steel. The presence of a magnetic constituent has been found by Hall" and by Avery, Homerberg, and Cook." Krivobok7 demonstrated the growth of magnetic constituents on reheating cold-worked specimens. Hadfield2,3 ' and Goss found no a iron. The steel from which the specimens were taken was commercial hot rolled % in. diam rod of electric furnace steel. The ladle analysis was as follows: C, 1.40 pct: Mn, 12.11; P, 0.060; S, 0.012; Si, 0.120; Ni, 0.080; and Cr, 0.090. Fifteen specimens, 6 in. long, were cut from a

Jan 1, 1953