Search Documents

By Ersin Yazici, Ahmet Bas, Haci Deveci

Pregnant leach solutions from waste of printed circuit boards (WPCB) leaching contain many impurity metals (Fe in particular) at significant levels. These impurities should be reduced to acceptable levels to avoid problems in downstream recovery processes e.g., low current efficiencies in electro-winning of copper from sulfate solutions in the presence of ferric. In this study, removal of iron in the form of goethite from synthetic (30 g/L Cu2+ and 1 M SO42-) and real leach solutions of WPCB was studied in some detail. The influences of initial concentration of iron (1-4.5 g/L Fe3+), pH (2.5-4.0), temperature (80-90°C) and seeding (23.5 g/L) were investigated over a period of 4 h. A significant increase in the iron precipitation was observed (i.e., from 68% to 96% over 4 h) with rising the pH from 2.5 to 4.0. The addition of seeds had also increased the removal rate over 4 h albeit to a limited extent i.e., from 96% to 99%. For the real leach solutions of sulfate (H2SO4-H2O2) and sulfate/chloride leaching (H2SO4-CuSO4-NaCl), precipitation of iron was found to be 63-73% (pH 2.5) and 93-98% (pH 4.0), respectively. The precipitates were further characterised by SEM-EDS analysis which showed the presence of copper (1-25%) in the precipitates indicating significant copper co-precipitation from the solution. These copper losses can be attributed to the formation of copper compounds such as anthlerite and brochantite within the range of pH (2.5-4.0) tested. This study showed that iron can be readily removed from synthetic/real leach solutions of WPCBs to a large extent (=93%) at the expense of high copper losses particularly at pH 4.0.

Jan 1, 2014

By R. M. Gammell

"INTRODUCTION The Farmer prospect was examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. As a result, studies of this property were included in a general preliminary investigation of the Etevens County lead-zinc deposits by the Bureau in 1945. The exploratory work was designed chiefly to supplement the surface examination by determining the nature of the mineralization below the zone of oxidization. The results of the small-scale diamond-drilling program undertaken at the property are presented in the following report.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization our resources to the end that they make the greatest possible contribution to security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work and prepares the filial report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Mar 1, 1947

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade. By the late 1990s, longwall mine output accounted for 40 percent of all underground output in the U.S., and today longwall mines account for approximately 50 percent of coal produced underground in the United States. A 53 percent increase in average shift production rates has occurred over the last fifteen years. This increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust provides an ongoing challenge for coal mine operators. The National Institute for Occupational Safety and Health (NIOSH) has completed a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify dust generation from major sources on the longwall section and to determine the relative effectiveness of the different control technologies in use today. Substantial reductions in dust levels were realized at sampling locations on the face when compared longwall surveys conduct in the 1990?s. This paper summarizes the results from the underground dust surveys and discusses current longwall dust control technology and operating practices.

Jan 1, 2010

By N. W. Martison, J. E. Hawley

"The Moulton Hill deposit is in the Eastern Townships of Quebec, 3 miles northeast of Sherbrooke. It is complex, both structurally and mineralogically, consisting of a narrow, irregular, mineralized zone that has been traced for a length of 600 feet, and in places to a depth of 1,000 feet, containing copper, lead, and zinc sulphides with a low content of gold and silver. It lies in a series of highly schistose micaceous rocks, believed to be of Ordovician age, but the mineralization is probably post-Lower Devonian. New details of the structure of the ore have become available since it was first described (1) , and as these show some striking peculiarities a further discussion is here merited .As detailed elsewhere, the deposit was discovered in 1942 as a result of regional geological studies followed by the application of electrical geophysical methods.Actual production began in July, 1944, and ceased in June, 1945. During the period July, 1944 to June, 1945, 75,643 tons were milled§, yielding the following:"

Jan 1, 1954

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .0, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

Jan 1, 1999

By Peter Kondos

The need for a sustainable development of ore deposits makes it imperative to be innovative and mindful in creating an economically and environmentally viable operation, while maintaining a good working relationship with the various stakeholders involved in developing and operating a large and complex mining project. This is becoming immensely important as gold ore deposits are becoming more mineralogically complex along with lower grades presenting both metallurgical and environmental challenges that need to be addressed in mitigating risks and improving project economics. This paper presents Barrick?s approach to development of strategic technologies for our long-term sustainable growth through conversion of valuable resources into reserves for both our green-field development projects and the expansion of our existing mining operations. Some of the key strategic solutions, including mineral processing, metallurgical and energy technologies, developed by Barrick and their impact on some of our complex gold and copper-gold ores will also be discussed in this paper. Keywords: gold ores, copper-gold ores, processing, breakthrough technologies

Sep 1, 2012

By Jochen Petersen, Jean-Paul Franzidis, Allan Nesbitt

This study presents a method for the determination of intra-particle diffusivities in ion-exchange resins for the purposes of evaluating the state of resin degradation during service. The method uses a zero length column (ZLC) in a closed circuit with variable speed pump and reservoir. The intra-particle diffusion is determined from absorption data by using the Nernst-Plank approximation along with the ‘mass transfer factor’ - which is a product of the mass transfer coefficient (kf )and the concentration of the adsorbing ion in the liquid at the surface of the resin - in a computer algorithm fitting simulated curves to experimental data.. Through this approach the changed intra-particle diffusivity, of a gel-type acid resin, over a 1000 loading and elution cycles, is shown.

Jan 1, 2014

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

By Chester Washburne

COLOMBIA has an almost ideal situation with respect to the world's markets, being only a short distance from the Panama canal and the West Indies. The sailing distance from its Caribbean ports to New York is less than that from Tampico. Geographically, Colombia consists of three systems of broad mountain ranges separated by two long narrow valleys. The Cauca River valley separates the Western or Coastal range from the Central range. On the west side of the Coastal range are the Atrato and San Juan Rivers. The Central and Eastern ranges are separated by the Magdalena River valley. In the department of Santander the Eastern range divides, one branch continuing northward as the Cordillera of Perija, the other turning eastward across Venezuela as the Cordillera of Merida. Between these ranges is the great basin occupied by Lake Maracaibo. These valleys consist mainly of long narrow reëntrants or tongues of Tertiary sediments between the older rocks of the mountain ranges. The late Miocene and younger sediments seem to have been deposited in separated basins, but the Cretaceous and possibly some earlier Tertiary strata were laid down more or less continuously over a great part of .Colombia and Venezuela. These strata were subsequently folded into the present ranges. The deposition of the Cretaceous and of some of the Tertiary was in a great sea, the main land mass being in Brazil, with land probably along some of the cores of the present mountain systems. The sediments, except the Lower Cretaceous, vary markedly in character and thickness. An illustration is seen in the massive series of non-marine conglomerates and sandstones of the upper Magdalena River valley, near Honda, which are almost wholly wanting in the coastal sections where marine sediments prevail. The oldest rocks bearing on the search for oil are the black carbonaceous and bituminous shales, limestones, and cherts of the upper part of the Lower Cretaceous. These probably are the main source of oil in both Colombia and Venezuela. They include thick bodies of true "oil shale. Above the carbonaceous and bituminous beds, lies a series of many thousand feet of clastic sediments. The most noticeable and easily recognizable formation among these clastic sediments is the "coal-bearing series," which may be either upper Cretaceous or Eocene. The

Jan 6, 1922

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

By Kadir Sariiz

Abstract - The Akçayir-Yürükakçayir Miocene-Pliocene basin in the Central Anatolia hosts ancient lacustrine sepiolite deposits. The succession in this basin consists of conglomerate (Yürükakçayir conglomerate), clayey and silty limestone, dolomitic marl, sepiolite beds and lenses, and dolomitic limestone (Kepeztepe formation). The main impurities within the sepiolite rock are dolomite, opal-CT, calcite, smectite and feldspar as sepiolite + dolomite and sepiolite + opal-CT are the main mineral assemblages. Smectite and feldspar are thought to be of detrital origin. Calcite is found as a secondary filling in root tubes and casts. Sepiolite samples studied display root-marks and root tubes, soapy and massive structure indicating direct precipitation. Sepiolite deposits probably formed at a pH of 8 to 9, and Mg+2 and SiO2 concentrations in moderately saline environments of internal facies of an alkaline lake.

Jan 1, 2000

Published by ?MILOS CONFERENCE CENTER ? GEORGE ELIOPOULOS? Editor Professor Z. AGIOUTANTIS Editorial Coordinator HELIOTOPOS ? PROFESSIONAL CONGRESS ORGANIZERS Layout IRINI KALOGIRU Production HELIOTOPOS ? PROFESSIONAL CONGRESS ORGANIZERS Cover PANAYOTIS PAPASTAMATIS HELIOTOPOS - PROFESSIONAL CONGRESS ORGANIZERS

Jan 1, 2003

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975