Search Documents

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

By Robert M. Asimow, Bisuddhi Riddhagni

THE use of back-reflection Laue photographs for crystal orientation is standard in many research projects. The time required for the orientation of any given crystal depends largely on luck and the skill of the investigator. In any case, where large numbers of crystals are used, this time can be quite considerable when the standard methods involving a Greninger chart and Wulff net are employed. For this reason the technique described below was developed. This new procedure applicable for cubic crystals (without preparation of new charts) largely eliminates the skill and luck factors and makes possible the determination of orientation in minutes. The procedure works in the following way: the Laue photograph is examined and arbitrarily an important hyperbola is picked out. An important hyperbola is defined as one which contains some spots through which several hyperbolas pass. Such a hyperbola inevitably corresponds to a low-index zone axis. The angles between the reflection planes causing all the spots on this hyperbola can be read directly from a Greninger chart in the usual manner. If the hyperbola contains more than five spots, these interplanar angles will positively identify the zone axis and the indices of each of the reflecting planes. However, initially since neither the zone axis nor the Miller indices of a diffraction spot are known, there are a very large number of possibilities that must be considered. Using tables of interplanar angles to check out every possibility would be quite tedious, so that this approach is not generally used. Instead, various poles are plotted on a stereographic projection. In the cubic system, however, it is possible to plot out once and for all the angles between all planes of a particular zone axis up to some upper limit of Miller indices. This has been done for all low-index zone axes in Fig. 1. Given these charts, it is quite a simple matter to identify the spots of the unknown hyperbola. All that is necessary is to plot the angles read off the Greninger chart to the same scale as Fig. l(b) on a strip of paper. Then this strip can be slid along each zone axis of Fig. l(a) until a good fit is obtained. Once this is accomplished, the Miller indices of each spot are given and thus the orientation problem is solved. To check, it is possible to pick a second hyperbola and see whether a compatible solution is obtained. This is most conveniently done by picking for the second hyperbola one that contains a spot common with the first. If the specimen axis is chosen parallel to the incident X-ray beam, then usually the [ loo] hyperbola will appear on the film as one of the more important hyperbolas and consequently will be either chosen initially or as a check. Using the [100] hyperbola, after the (001) or (011) spots have been identified, the latitude and longitude of the specimen axis can be read directly from the Greninger chart so that it is unnecessary to use a Wulff net for the entire orientation procedure. This makes the operation not only quicker but more accurate. Of course, if neither the first nor second hyperbolas correspond to [loo] then a third hyperbola can be chosen.

Jan 1, 1967

By D. E. Hulse

"Social License, the consent of the neighbors and community to develop and operate a mine, has received little attention until recently. Though social license is intangible, not having this relationship with the community carries operational and economic risk to a project, potentially including future impairment of the asset. Acquiring and maintaining social license is a long term personal relationship. It requires communication, commitment, consistency, and transparency. This presentation will review the building blocks to acquire and maintain a social license based on experiences with mining projects in Mexico. INTRODUCTION Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them” (Agricola 1556). In 2015 it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate. “Most commonly, the SLO is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders.” (Bice 2014) A generation ago I learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three legged stool is a very stable structure.In 2015 it seems that we have added some other legs to the stool. The JORC code addresses “social, and governmental factors” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves”. The Canadian CIM Guidelines refer to “environmental, legal and social data” (CIM 2003).Compared to these the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the Competent Person."

Jan 1, 2016

By K. L. Hardee

A recent development has emerged which produces a retrofittable, low cost anode by attaching disposable, electrocatalytically active titanium mesh over the existing lead anodes. The coated titanium mesh anode operates at potentials of several hundred millivolts lower than the lead anode, providing significant power savings. The exposed lead surfaces are stabilized since most of the current flows through the titanium mesh. With the minimal lead corrosion, the sludge formation is virtually eliminated and the purity of the plated copper is greatly enhanced. Further savings may be realized by the elimination of non-essential chemicals such as cobalt. Since the combination anode is stable and uniform, the plated copper is also more uniform with minimal formation of dendrites, reducing the shorting. Full-size anodes have been tested for over 6 months in commercial copper electrowinning cells. The laboratory and field performance of the stabilized lead anode will be reviewed, including the voltage characteristics, the lead stability and the copper cathode purity.

Jan 1, 1999

By J. R. Shouldice

"IntroductionREEFS of Silurian age are recognized in southwestern Ontario, both in outcrop and from subsurface information. This paper deals with the so-called 'pinnacle' reefs which are known only in the subsurface. For the purpose of this paper, the pinnacle reefs are arbitrarily defined as those structures having a height of over 250 feet and a length of less than two miles. This definition eliminates numerous mounds and other broader, more subdued, structures of less certain origin, found in subsurface beds.The term 'pinnacle reef' is perhaps unfortunate, but it is in common usage in Ontario and is used elsewhere for different types of reefs. A new name is justified by the unusual environment and structure of the Ontario reefs, but it is unlikely that any other term would gain acceptance. Rather than propose a new term which would be ignored or result in further confusion and misuse, the name 'pinnacle', as defined above, is used in this paper.Pinnacle reefs have been found over a fairly large part of southwestern Ontario. The known reefs of this type parallel the southeast edge of lake Huron and •follow the strike of the structure contours which circle the Michigan basin (see Figure 1). In total, twenty-five such reefs have been discovered in southwestern Ontario."

Jan 1, 1955

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By Juan Mori

El presente texto describe la evolución de la tecnología con sus limitaciones iniciales en su aplicación, los cambios culturales de una empresa y su relación con las necesidades del conocimiento, y la globalización de los mercados y los nuevos roles de los socios estratégicos. En este sentido, el nivel competitivo de las organizaciones exige la implementación de diversas estrategias en la Gestión estratégica de costos para supervisar las desviaciones, cambios, y tendencias en la información histórica para encaminar la estrategia de la situación actual y futura.

Oct 21, 2015

By Z. Liang, Z. Q. Liu, X. F. Li, H. L. Zhang

"Dynamic characteristics of frozen soil is important for the safe, effective and rapid construction in cold regions and artificially frozen engineering. In this paper, dynamic characteristics of frozen clay with various low temperature and different strain rate were studied by using Split Hopkinson Pressure Bar (SHPB) test and numerical simulation test. Variation of dynamical parameters and dynamic stress-strain curves of frozen clay were obtained and analyzed. The results of these test show that: Frozen clay exhibits temperature effect and strain rate effect that the failure type tends from plastic failure to brittle failure with the increase of strain rate or decrease of temperature; Under impact loading, frozen clay exhibits three typical dynamic stress-strain curves as strain rate increases, and the maximum strain of frozen clay only linear increases with strain rate.INTRODUCTIONArtificial freezing technology has been widely used in the construction of underground engineering, such as the coal mine shaft, the deep foundation pit, the urban metro and subsea tunnel, etc. Research on dynamic mechanical behavior of artificial frozen soil will provide supports for these artificially frozen engineering (Xu et al. 1998; Ma 2009). However, the dynamic mechanical research on frozen soil is mainly carried out at low frequencies or small amplitudes of the waves, behavior of frozen soil under impact loads or high strain rate loads has not been made clear."

Jan 1, 2015

By G. K. Manning, M. C. Udy, L. W. Eastwood

Those who have examined beryllium and beryllium-rich alloys under the microscope have noted the results of the difficulties encountered when preparing these materials for examination. Hard constituents are readily chipped and pulled out of the matrix, and the soft ones are easily gouged out or embedded with abrasive or other material. The matrix is easily deformed, which makes it very difficult to remove the effects of scratches. Furthermore, the matrix and some of the constituents are also readily pitted during etching, which makes the structure difficult to develop. The metallographic techniques designed to avoid these difficulties are neither radically new nor necessarily the best possible procedures. They were developed at Battelle to fill immediate requirements as part of a study of the preparation and pouring of beryllium melts as described in a separate paper. A part of the research program on the causes of gas unsoundness in beryllium castings entailed a study of the effects of such gases or gas formers as oxygen or oxides, nitrogen or nitrides, and carbon or carbides. These gases or gas formers, if dissolved in the melt, might be an important factor in the study of unsoundness caused by gas evolution in beryllium. Because it was necessary to be able to distinguish these gases or gas formers, if present as alloy constituents, from metallic phases also present as alloy constituents, a series of alloys was prepared with additions of the various possible metallic and non-metallic constituent formers. It should be emphasized that the constituents referred to as gases or gas formers are important in the study of gases in beryllium only if they form a part of the alloy, that is, if they dissolve in the liquid or solid metal. During the first part of the development of metallographic techniques, the Massachusetts Institute of Technology, unpublished report (TC 3315, Nov., 1945) by Paul Gordon, describing various microconstituents in beryllium, was quite useful. Of particular interest in this report is the confirmation of one of the conclusions drawn from the present investigation, that is, that a distinct oxide phase apparently does not occur in beryllium. The Preparation of Metallographic Specimens GRINDING PROCEDURE The original specimen is either sawed or cut on an abrasive wheel to a convenient size. For best results, the surface to be polished should not be more than about 1/4 in. square, and it is convenient to mount the specimens in bakelite to facilitate handling. Two alternative grinding procedures have been developed. As one alternative, specimens are ground successively on 120-, 240-, and 400-grit, wet-or-dry metallographic discs. The abrasive discs are revolved at 1750 rpm on a conventional pedestal grinder. The coarsest disc (120 grit) is used either wet or dry, and in most instances, it can be eliminated from the procedure. Grinding on the two finer discs (240 and 400 grit) is accompanied by the application of kerosene. The technique consists of holding an oil can, containing kerosene, in one hand and the mounted specimen in the other hand. While the grinding is being done, several drops of kerosene are applied every few seconds close to the center of the disc. Carbon tetrachloride serves at least as well as kerosene as a lubricant; perhaps it is slightly better, but it volatilizes so readily that an additional health hazard is involved. Light oils and water are not satisfactory for the finer grinding operations. The second procedure is perhaps slightly slower than the first and requires a more careful technique, but it eliminates the use of kerosene. The specimen is first ground wet on a 240-grit disc, followed by dry grinding on a 400-grit disc. Finer grinding does not appear to be necessary with either of the two alternative procedures. The pressures used throughout either grinding operation must be extremely light, that is, barely sufficient to hold the specimen in contact with the disc; otherwise, flow and chipping are almost certain to occur. In both procedures, it is essential that the discs be sharp and that they be discarded as they show evidence of becoming dull or loaded. In general, not more than four or five specimens can be ground on a disc before the disc becomes dull enough to warrant discarding it.

Jan 1, 1950

By David A. Sterling

Approximately 50 percent of the uranium resource of the Free World is in deposits of Precambrian age, principally in lower Proterozoic conglomerates in Canada and South Africa (Uranium Resources, Joint Report, ENEA and IAEA, 1967). Most of the uranium resource of the United States is in Mesozoic and Cenozoic continental clastic sedimentary rocks that fill intracratonic basins. The Atomic Energy Commission is investigating the distribution of uranium and thorium in the Precambrian of the Western United States and the relationship of, time-space-facies patterns of uranium and thorium enrichment in the Precambrian to the major resources of uranium in the Mesozoic and Cenozoic host sedimentary rocks. This paper summarizes the results of preliminary studies of the Precambrian in the Southwestern United States including New Mexico, Arizona, southern Nevada, and southern California (Fig. 1). The host rock provenances for the major uranium resources in epigenetic deposits of Mesozoic and Cenozoic age in the Western United States were in areas of extensive Precambrian exposure along the eastern margin of the Phanerozoic geosynclinal belt (Fig. 2). Mesozoic continental clastic sediments in the Colorado Plateau contain about two-thirds of the uranium resource of the United States. These sediments formed from detritus derived from the Mogollon highland in the Southwestern United States where the Precambrian was extensively exposed (Stewart, et al., 19593 McKee, et al., 1959; McKee, et al., 1956; Craig, et al., 1955) (Fig. 2). A genetic relationship may exist between this provenance and the major uranium deposits of the Colorado Plateau. The Precambrian might be equally important in the genesis of uranium deposits whether the most important process in the formation of these deposits was the leaching of low-order intrinsic amounts of uranium from Precambrian granite or from Mesozoic pyroclastics derived from syntexis of the Precambrian basement rocks (Malan, 1968).

Jan 1, 1969

By D. W. Davis, P. Landais, L. J. Robb

Abstract -Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Pb-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter ?13C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoid­ and sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By G. Asai

The Bureau of Mines has been engaged in a program to increase the utilization of chromium by providing samples to individuals and institutions requesting chromium for research investigations. This report consists of a tabulation of the disposition of chromium samples distributed from July 1953 through June 1961; 109 requests for chromium were answered by providing chromium as electrolytic plate, powder, or wrought forms. The demand for samples reached a peak in fiscal year 1959 and declined to a relatively low level in fiscal year 1961. The largest number of requests came from individuals engaged in mechanical property studies; there were also many requests from those concerned with vaporized metal and physical properties studies. Most noteworthy application for chromium was the experimental use of the radioactive form, Cr[51], in radiotherapy of cancer.

Jan 1, 1964

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By Lilly PA, Kavetsky AP

An empirical, kinematic model is developed which calculates the trajectory of individual blocks of rock in a blast, their point of impact in the muckpile and the final shape of the muckpile. The method is based on the determination of initial block velocity and requires input on stemming length, bench height, subdrill, burden, spacing, energy of explosive per unit length of blasthole, energy attenuation rate and resistance to movement. The model, which will form part of a comprehensive blast simulation package, has application in open cut mining in predicting muckpile geometry and the movement of grade blocks during blasting, which in turn impact on shovel productivity and grade control.

Jan 1, 1986

By Nicholas Chlumecky

To date information is somewhat limited concerning the strength and bearing capacity of floor strata, which is of great importance where proper roof control is desired. If the bearing strength of strata is not known, the support may be excessively strong in relation to the support capacity of the floor, with the result that strong props sink into the floor strata, giving them dubious value as a roof support. The method described is used to determine how tests are made on dry rock to determine the required support area for the base of props or other structures which may rest on rock strata in mines. Relationships were established for the bearing capacity of rocks which were subjected to loads by means of bearing areas of various sizes ranging from 0.09 sq cm (.014 sq in.) to 700 sq cm (108.5 sq in.). This permits the evaluation of the bearing capacity of rocks by testing small areas for the de- termination of the capacity of larger areas.

Jan 3, 1968

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.