Search Documents

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By D. Gove

Several coal mines in Southeastern United State face the problem of multiple, very thin coal seams or seams adhering to interburden, and because of the strip ratio economics, these seams must be recovered. Over the past few years several mines have discovered a common method to solving these problems...use of a Caterpillar RR-250 Road Reclaimer.

Jan 1, 1995

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By M Roche, W J. Huxley

Finding a balance between practical and acceptable groundwater management, and providing for the needs and impacts of mining developments remains a challenge. The changes that accompanied the recent implementation of water reforms have provided greater flexibility for the water manager and greater certainty for the resource user. However uncertainty associated with understanding of complex aquifer systems, balanced against providing for the needs of mining developments, the rights of existing water resource users and expectations of the broader community have not diminished the conflicting issues faced by water resource managers and resource developers. Licensing under the Water Act 2000 provides the regulatory link with the taking of water for water supply purposes or as a consequence of the mining activity. This paper outlines key elements of sustainable water resource management involving certainty of access to water and adaptive environmental management that are delivered through conditioning the water licences issued for the particular mining development. Implementation of this approach is illustrated through a case study involving the BHP Billiton Cannington Mine in North West Queensland.

Jan 1, 2003

By Alan M. Ritchie, Paul Miskelly

The 2-D code FIDHELM has been used to simulate conditions in piles of pyritic material with vertical dimensions of 20 to 70 m and a horizontal dimension of 500m. Those properties of the pile and its external environment (wind, temperature) important in determining the time and space dependence of sulfide oxidation, have been identified. A prescription to evaluate the overall sulfide oxidation rate in a pile of known volume but variable geometry has been developed.

Jan 1, 2000

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By Kumar M. Lyer

Residence time distribution (RTD) of light and heavy liquids in a pyrometallurgical channel reactor was mathematically modeled by representing the reactor as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength bottom gas injection. The experimental variables include flow rates, heights, density and viscosity of the two liquids; gas flow rate; injector diameter; and distance between injectors. The experiments covered a wide range, of the appropriate dimensionless parameter, including conditions in ferrous and nonferrous extractive metallurgy. Dispersion modeling studies were also carried out to determine the degree of backmixing. Results indicate that the degree of backmixing in the channel reactor for various operating conditions corresponds to that for 3-20 perfectly mixed reactors in series.

Jan 1, 1993

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Kyle J. H, Misra V. N

The most recent development in gold processing is the increasing use of heap leaching for the extraction of gold from low grade ore, and old tailings dumps. The reason for this trend is mainly to do with economics. The advantage of heap leaching is the considerable saving in both capital and operating costs. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have suitable permeability char- acteristics, and the gold recovery is poorer than by conventional process. In this study, an attempt has ben made to ascertain the heap leaching characteristics of Western Australian gold ores on the bench scale using multiple, appropriately sized leach columns. The influence of particle size, flow rate, column depth and leaching time on the rate of gold extraction was determined. The percolation rate of cyanide leaching solution was deter- mined with and without gypsum additions. Efforts were also made to minimise particle segregation, fines migration and solution channelling during leaching, so as to improve solution percolation, gold extraction rate and recovery.

Jan 1, 1991

By F. Musuka, D. Jenkins, A. Keyes

BHP Olympic Dam operates a Direct-to-Blister copper flash smelting Furnace (DBF) and an Electric Slag Cleaning Furnace (ESCF). Tapping blister copper from these furnaces via tapholes is a routine task carried out by trained personnel. Blister tapping is a high-risk activity with personnel operating in close proximity to molten metal. BHP’s risk management framework has identified taphole integrity as key to managing the potential for loss of molten metal containment and molten metal – water steam explosion, both of which have the potential to cause multiple fatalities. As part of the focus on managing this risk, since 2017, a dedicated Taphole Development Team has been embedded in the operation to run an accelerated improvement program focused on safely and sustainably embedding an improved taphole design with greater integrity. The program of works includes selecting and testing of new materials as well as improving operating discipline by collaborating with tapping personnel to convert their knowledge into codified condition monitoring and operating strategies. Computational fluid dynamics (CFD) is being used to derive critical risk controls, and to develop live-alerts to infer excessive refractory insert wear. To date, improving DBF blister taphole mudgun clay has led to more consistent drilling depths and subsequently reduced oxygen lancing requirements, resulting in improvements in taphole insert service life. On the ESCF, insert performance testing and development of a new taphole condition monitoring strategy, is being used to increase taphole insert tonnages to more sustainable levels. Operations personnel have been closely involved in different phases of the change management, this has led to standardization of tapping practices for both furnaces, and improved ownership of the proposed changes. The paper discusses the maturity in taphole integrity risk management as a result of recent and ongoing developments. It then provides an overview of future taphole developments proposed at Olympic Dam. INTRODUCTION Tapping operations at Olympic Dam and learning from significant events The Direct-to-Blister furnace (DBF) at Olympic Dam was built with a conventional design blister taphole, which was designed for manual oxygen lancing and clay stopper bar plugging tapping operations (Campbell, 2005). Manual tapping is a high-risk activity, where personnel work in close proximity to molten metal, and molten metal personal protective clothing and equipment must be used. Opening tapholes by oxygen lancing is a skilled activity and unintentional damage to the taphole inserts can occur. Since 2008, a Mudgun and Drill unit has been developed and trialled and is now in use on the DBF blister tapholes, to remove personnel from the line of fire when opening and closing tapholes. This has the additional benefit of reducing lancing damage to taphole inserts. A new taphole design labelled the Modular Blister Taphole (MBTH) was developed at Olympic Dam for the Mudgun and Drill operation. The intent of the design was for mudgun clay to fill the entire tapping channel when plugging after a tap. The drill would then drill through this clay plug to open the taphole.

Jan 1, 2019

By G. S. Hume

As predicted a year ago, owing to the discovery in 1936 of crude oil on the west flank of the south end of Tuner Valley in the eastern foothills of Alberta, 50 miles southwest of Calgary, and the drilling activity that resulted, the production of crude oil in Canada during 1937 showed a very substantial increase over the previous year. The production from other parts of Canada is relatively small and shows slight variations only from year to year. The production of crude oil in Canada and the production in Alberta, the main producing Province, is shown in Tables 1 and 2.

Jan 1, 1938

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By Georgios Kalamaras, Sebastiano Pelizza, Carlo Alessio

"This article describes, through the presentation of five cases-history, technological advances that the Authors together with Tunneling Contractors devised for coping with adverse geotechnical conditions. It is believed that by introducing these new elements in a method that has proven its value in Italy and abroad for the last 40 years, the umbrella arch method, due to its versatility and simplicity, can become a universal method for conventional tunneling in very poor ground conditions. After a description of common faults and mistakes in applying the method, 5 projects are presented which demonstrate that self-drilling pipes give excellent results in terms of performance a zero volume loss, while, function of the ground conditions the various grouting mixtures used, such as expansive jet-injected cement-base grouts and bi-component resins, extend the use of the umbrella-arch in variety of grounds even in presence of water-bearing lenses. The case-histories provide successful applications in different conditions.BASIC FEATURES OF UMBRELLA ARCH METHODThe umbrella arch method provides a short support of the tunnel vault just ahead of the excavation face. The method foresees the drilling and installation of peripheral, sub-horizontal steel pipes in the ground, followed by their grouting. The umbrella arch method is also known as forepoling, steel pipe umbrella, reinforced protective umbrella or simply “umbrella”. The umbrella arch method does not have a static function because the immediate stabilization of tunnel section is entrusted to the internal shell of steel ribs and shotcrete. The “umbrella” provides a pre-support of the excavation which has to be stable for an adequate length and duration permitting the installation of the next steel rib and shotcrete under conditions of safety (Figure 1).The umbrella-arch provides pre-reinforcement of poor ground around the tunnel perimeter in a simple and flexible manner that is adaptable to different ground conditions. In fact, it is possible to vary the number and length of pipes, the distance between them, their diameter and thickness as well as the overlapping length of two succeeding umbrella arches. The versatility of the umbrella arch technique allows its application to: clay deposits, granular alluvial deposits, moraine and debris materials even when containing large blocks, heavily jointed, foliated and tectonically disturbed rock masses."

Jan 1, 2016

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By Dalmijn WL, Valk HJLvd

At the Faculty of Mining and Petroleum Engineering, the Department of Raw Materials Technology, a mathematical model has been developed to predict the porosity distribution in an uniform jig bed. If the porosity distribution in an uniform jig bed is known, it is possible to correlate this to the settling velocity of particles with a density different from the density of the bed grains and thus model the stratification in a jig. For measuring the porosity distribution in the jig bed a method has been developed based on light absorption techniques.

Jan 1, 1993

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By J. M. Singer

Flame propagation of lower limit hybrid coal dust-methane-air mixtures in vertical and horizontal flame ducts of 15.2 cm id and 1.8 m length has been investigated to provide information bearing on safety in mines. Fuel concentrations at lower limits of flame propagation and equivalences of coal dust and methane are much higher for continuing flame propagation than for short-span flame propagation in the vicinity of an "overdriving" ignition source. As the energy of the ignition source was increased, the flame speed and the distance of flame propagation from the ignition source increased, whereas the total fuel concentration at the lower limit decreased.

Jan 1, 1968

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000