Search Documents

By John H. Paugh

Hydraulic slurrying and pumpability characteristics of phosphate matrix (ore) have not been quantitatively defined. An elemental triangular diagram analysis of rock/sediment texture is used to classify the nature of the ore; then related to empirical field data of hydraulic pressureand production yardage ratios. This experiment is applied as a geotechnical tool to provide empirical data of ore slurry and pumpability characteristics as key considerations in the design of slurry pipeline systems. A real texture variability maps are developed on a section of land to assist mine engineering planning.

Jan 1, 1981

It is now widely accepted that horizontal stress is present nearly everywhere underground. Often it is more severe than the vertical stress. It is a major cause of roof control problems in underground mines. The AHSEM computer program contains two modules to improve mine layouts for control of horizontal stress. For development, the user specifies the orientations of the maximum horizontal stress, the entries, and the crosscuts. Angled crosscuts may be used, and the angles may be different for the right- and left-hand crosscuts. AHSEM then shows the user how the stress condition would vary as the entry and crosscut orientations are changed. The second module is for longwall mining. Severe stress concentrations can make headgate conditions hazardous when the entries are improperly oriented. AHSEM shows whether a particular longwall orientation and extraction sequence places the headgate corner in a stress concentration or in stress relief. It also estimates the magnitude of the stress concentration.

Apr 1, 2003

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By Lewis A. Martin

Researchers from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, in cooperation with engineers from the Department of Mining and Geological Engineering, Montana Tech, Butte, MT, conducted tests to evaluate the tensile strength, fiber count, and adhesion of shotcrete applied to panels at the Chief Joseph Mine, a research and training facility operated by Montana Tech. The tests were conducted in the mine ramp 45 m (150 ft) inward from the access portal at a 15.25-m- (50-ft) long test area divided into five 3-m- (10-ft) long sections. The shotcrete was applied with an Aliva 240.5 machine fitted with a predampener. Different amounts of fiber were entrained for each panel. Background data for the tests were obtained from earlier tests in Nevada, where the typical amount of fiber in the shotcrete is 6.54 kg/m3 (11 lb/yd3). All shotcrete was applied to a minimum thickness of 76 mm (3 in). Cylindrical cores were drilled at the wall-rock interface, and adhesion was tested after 28 days of curing. The goal of this research is to reduce the need to install multiple supports at the advancing face by creating a safer mining system that limits the time miners are exposed to unprotected roof.

Jan 1, 2004

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

By Byron Pickard

AT MIDNIGHT of Sunday, Aug. 27, 1922, a fire was discovered in the main shaft of the Argonaut mine, Jackson, Cal. With the excep-tion of a shift boss and two skip tenders who escaped, the entire night shift of 47 men was trapped in the mine and entombed for 22 days, when the bodies were recovered. The entombed miners made a valiant but fruitless effort to save their lives. Rescue crews toiled strenu-ously day and night for 21 days to save the entombed men, only to find they had arrived too late. From the experiences of the entombed miners and of the rescue crews, valuable lessons may be learned to prevent future catastrophes.

Jan 11, 1922

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By P. Taskinen, D. Lindberg, H. Viitala

The formation of copper chlorides in flue dust or deposits in heat recovery boiler of copper smelters or waste-fired boilers may lead to formation of corrosive partially molten deposits on walls and heat exchangers of the boilers. These deposits can contain various other metals, such as alkalis, Fe, Zn, Pb together with oxides and sulfates. In the present study, a thermodynamic model for copper-containing binary and ternary metal chloride systems within multicomponent CuCl-CuCl2-FeCl2-FeCl3- PbCl2-ZnCl2 system has been assessed and optimized based on own experimental phase equilibrium data, as well as literature data. The thermodynamic properties of the liquid phase was modelled using the quasichemical quadruplet model and a thermodynamic database was optimized to predict all available experimental data within the experimental error limits. The thermodynamic database allows for more accurate predictions of potential corrosion-related issues in various heat recovery boilers and waste-fired boilers due to formation of copper chlorides. INTRODUCTION In the copper flash smelting, flue dust can cause severe problems in the gas train, used for separating dust from the SO2-rich off gas, by forming corroding accretions on the walls of the heat recovery boiler. Formation of dust build-ups in the boiler need to be cleaned regularly and potential corrosion damage checked, requiring costly and unscheduled shutdowns of the flash smelting process. Compounds of copper and zinc among other elements having high vapour pressures may volatilize during the smelting of the copper concentrate, forming dust when the process gas cools down. Also, particles of solid or liquid iron oxides originating from the ore get transported with process gas to the heat recovery boiler as a result of entrainment in the flue gas (Miettinen, 2008) The dust deposit build-ups on the boiler walls are formed partly by direct impact of particles and partly by vapour condensation on the boiler walls. The initial deposition takes place by the condensation of vapours that contain zinc, lead, arsenic and other metals having high vapour pressures. Also, low melting point eutectic components of alkali salts such as chlorides and sulphates can act as sticky cohesive particles attaching to the boiler walls. The fine particles landing on the surface of the porous dust deposit layer react in the SO2-rich atmosphere of the boiler to sulphates. The process gas within the boiler contains SO2, O2, SO3, H2O and N2 that diffuse into the porous accretions to form a stagnant gas layer within the dust deposit structure. The composition of this gas layer may differ greatly from the composition of the process gas that is flowing on the surface of the accretion layer. Locally HCl and H2SO4 are formed and even a reducing atmosphere may exist within the dust deposit layer, allowing new reactions to take place. The local micro-atmosphere may enable metal sulphates to be reduced to secondary sulphides and even metallic components. Within the accretion layer, components may be formed that would not be stable in the gas atmosphere inside the boiler (Miettinen, 2008). This may be the mechanism by which for instance chlorides of Cu, Fe and Zn are formed within the deposit layer.

Jan 1, 2019

By R. Y. Wan

Thiocyanate was evaluated for gold recovery from low-grade refractory gold ores following biooxidation for an acidic heap leaching approach. One of the important features in using thiocyanate is that the leaching can be performed in acidic media, thus avoiding problems related to neutralization and material handling as leaching with alkaline cyanide. Also, the acidic leaching enables the use of ferric ion or bioleach solution as oxidants. In this study, Newmont-Nevada low-grade refractory sulfidic ore was biooxidized in columns at a particle size of 100% passing 102 mm. Thiocyanate leach on the biooxidized ore sample was performed on both ground samples in pulps and coarse material in columns using ferric ion as an oxidant. The variables of thiocyanate and ferric ion concentrations were compared for effect on leaching. Thiocyanate leach results are encouraging and indicate potential for development of a practical process. Gold extractions by thiocyanate are comparable to cyanide leach. Thiocyanate consumption was higher than cyanide, but was in an acceptable level.

Jan 1, 2003

By Wei-ling Wang, Ryosuke O. Suzuki, Xiang-ning Meng, Miao-yong Zhu

"A finite-element thermal-stress model of continuous casting mold is conducted to predict deformation of copper plates and its change with different cooling structure. The results show that deformation behavior of copper plates is mainly governed by cooling structure and thermal- mechanical conditions, deformation amount is related to structure geometry, and a small deformation mutation occurs in cooper-nickel boundary due to different properties. The maximum deformation of hot surface centricities of wide face locate at 100 mm below meniscus and that of narrow face locate at meniscus and terminal of water slots and significant curvature fluctuations on both sides of copper-nickel boundary. The maximum deformation of centricities is increased up to 0.05 mm with thickness increment 5 mm of copper plates, and maximum deformations are only depressed 0.01 mm and 0.02 mm with increments of 1 mm nickel layer thickness and 2 mm water slot depth respectively.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipate in primary cooling zone and make continuous casting mold under enormous heating load giving rise to thermal stress, deformation, high-temperature fatigue and creep not only depress mold life-span, but reduce casting stability [1] Many studies focused more on heat transfer, solidification and shrinkage of solidifying shell to provide inverse proposals for optimizing cooling system and even designing new taper of mold [2,3], but it is generally useless to those of having been manufactured or being put into production. Therefore, mold-related forward problems show necessity to be discussed deeply, and stress and deformation distributions based on special thermal conditions in mold should be analyzed in order to explore suitable cooling structure of mold directly. Samarasekera et al. [4] examined heat flow and distortion of two-dimensional longitudinal sections and investigated effect of cooling water velocity, copper plates thickness and carbon content on formation of rhomboidity and longitudinal comer cracks. O'Connor et al. [5] developed a three-dimensional mathematical model to compute thermo-mechanical state in thin-slab mold and calculated temperature and deformation of mold wall to assess roles of various process parameters on impacting mold life. Thomas et al. [6] predicted temperature, distortion and residual stress in mold and indicated increased distortion requires increased remachining, which reduces mold life and increased residual stress increases the probability of a catastrophic crack failure. Park et al. [7l determined heat-flux profiles in funnel-shaped and parallel thin-slab molds based on an inverse heat conduction model and thermocouple temperature measured in-plant and put them into three- dimensional finite-element thermal-stress model to predict temperature, distortion and residual stress of mold wall. Korie et al. [SJ focused on prediction of temperature, distortion and residual stress in mold and in particular to clarify that mold life is significantly affected by temperature and its rigidity, but little effect by mechanical including clamping force, bolt prestress, friction and ferrostatic pressure. Meng et al. [9l predicted temperature and thermal stress in a slab mold and analyzed effect by cooling system geometry and casting speed quantitatively. In present study, a three-dimensional finite-element thermo-mechanical model with type-switched element is transformed from previous heat-transfer finite-element model [9l, and mold deformation is simulated in order to shed light on thermo-mechanical behavior with special thermal conditions and different mold geometry at high casting speed."

Jan 1, 2013

By M. Kaya

The main purpose of this study was to design a modular/mobile coal preparation plant with a capacity of 300 t/h for Seyitömer B3 vein (almost 70% of the whole SLI deposit). Firstly, coal washing properties and washability curves were determined by sink and float tests. Then, equipment sizing, selection, flow sheet development, economic evaluation, investment and operating costs were determined for coarse (-150+18mm), fine (-18+0.5mm) and slime (-0.5+0.1mm) coals. Economic evaluation of the proposed flow sheet showed the feasibility and profitability of the investment.

Jan 1, 2006

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By Robert L. Mentch

CADMIUM is one of the metals apparently destined to remain relatively scarce. The en tire supply of primary cadmium is recovered as a byproduct, concurrently with the treatment of ores of other metals. Development of the cadmium industry is attributed to metallurgical improvements in the zinc industry; output depends almost wholly upon zinc production. Cadmium is a metal of specialized uses where its superior performance has developed a strong, expanding demand. The supply, however, has been relatively unresponsive to price because of its byproduct nature. Cadmium's outstanding properties would assure it a manyfold greater market if more were available at lower prices.

Jan 1, 1958

By A. Deneys

This paper reviews industrial gases used in primary copper production. Copper smelting industrial gas demand has steadily increased since the first commercial oxygenconcentrate smelting in 1952 [1]. In copper production oxygen for smelting is the dominant industrial gas use followed by oxygen for converting. Nitrogen is finding increased use in copper smelters. Nitrogen is used for porous plugs for copper converting and anode refining [2-5]. Nitrogen can be used for concentrate drying [6,7] and is also used in some Ni-Cu smelters as a coolant in Peirce-Smith converting [8,9]. Industrial gas supply options of cryogenic or adsorbent based on-site plant or cryogenic liquid delivery are detailed.

Jan 1, 2007

By P. Barnes

THE object of this paper is to make a brief comparison of the out-lines of several forms of ports for steel-melting furnaces, in reference chiefly to the proper mixture of the gas and air, and to the direction in which the flame is thrown down into. the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M. Pernot, of St Chamond, France. This is used with the dome roof preferred by him for the revolving bottom that bears his name. From No. I has been derived No. 2. This is shown on the plans of Mr., A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched. roof of nearly the ordinary form., instead of over the top of the roof, as with the done of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or “washing” -to use the briefer French term. In this the gas and air come into contact in broad sheets one above the. other. Fig. 5 shows the form used by Messrs, Richmond & Potts

Jan 1, 1881

By A. C. Cascalheira, L. M. Abrantes, M. Savic

This paper reports our results on the application of a novel process for the spontaneous and sustained reduction and recovery of elemental silver and gold on an electroactive polymer surface. This work incorporates the metal recovery from photographic films (silver) and goldsmith residues (gold), by direct contact of metal containing solutions with polymer. The performance on such process of electrochemically and chemically prepared polyaniline (P ANI) is evaluated. SEM coupled with EDX and XRD analyses confirmed the presence of metallic silver and gold deposited onto polymeric material.

Jan 1, 2000