Search Documents

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By J. C. Todd

The volume of air needed to move the combustion wave through each acre-foot of the reservoir is a very important quantity for engineering economic analyses. A new method, which involves backflowing the injection well, has been developed for determining the air requirement .for the forward combustion thermal pilot in the Delaware-Childers field. The method depends on measurement of the total volume of air injected and measurement of the pore volume in the zone swept out by the combustion front. The basic premise of the method is that the pore volume of the swept zone contains air, while the formation around this zone contains flue gas, oil and water. The pore volume of the swept zone is determined by blowing down the pilot section of the formation through the injection well after the pilot is shut down. Oxygen balance is used to differentiate between air from the swept zone and flue gas from the surrounding formation. Data indicate that air'is produced from the swept zone by relatively efficient miscible displacement by the flue gas. The pore volume occupied by the air in the swept zone is determined by simple PVT relationships. The average temperature of the swept zone is calculated by heat balance from the total amount of heat generated during the pilot and losses to the surrounding formation. The new method was applied successfully at the conclusion of the pilot in the Delaware-Childers field; the air required for the reservoir conditions involved was calculated to be 19.2 MMscf/acre-ft of reservoir swept. INTRODUCTION One of the most important pieces of information to be found from a forward combustion pilot is the air requirement; that is, the volume of air needed to move the combustion wave through each acre-foot of the reservoir. Compression costs per barrel of oil recovered, which are a direct function of the air requirement, are a large portion of the expenses incurred in the thermal recovery process. Thus, the profitability of thermal recovery depends largely on the air requirement, which is a measure of the amount of fuel deposited and burned in the thermal recovery process. Several attempts have been made to correlate crude oil properties with fuel deposition and, hence, air requirement.l*2 Other attempts have been made by our laboratory to find the air requirement by material balance, gravity survey, pressure transient analysis,3 magnetic survey and the poten-tiometric model. Better methods are needed to predict more accurately the economics of fieldwide application of the process. Another method of finding the air requirement consists of operating a pilot thermal project for several years. This is followed by an extensive coring program to define the volume swept by the combustion wave. The air requirement is found from the total injected air divided by the volume of the swept region found from the coring operation. This method is costly; an adequate coring program usually costs several hundred thousand dollars. A thermal pilot was operated in a watered-out portion of the Delaware-Childers field, Bartlesville sand, from Nov., 1960, until May 3, 1965. One of the primary purposes of this pilot operation was to determine the air requirement for economic calculations which determine the advisability of expanding the project to the entire 128,000 acre-ft field. Barnes4 has described the result of this pilot operation,, including calculation of the air requirement from limited coring data. The value obtained, as calculated, was 15.8 MMscf/acre-ft. One purpose of this report is to describe a new method of finding the air requirement from a thermal pilot operation. A second purpose is to describe the application of this method to the Delaware-Childers thermal pilot. THEORY AND DESCRIPTION OF THE METHOD The combustion zone in the forward combustion process is propagated from injection w producing

Jan 1, 1970

The evolution of mineral sand mine rehab ilitation techniques have been techniqually based. Research and investigations have been carried out by government authorities, mining companies and academic institutions. Protection of the physical and biological environments is a vital part of any mine oper- ation. The Mineral Sands Mining Industry in New South Wales is successfully working within the State's environmental framework and is meeting; community requirements and expectations concerned with the environment and mine rehab- ilitation. Keywords: Environment, mineral sands mining, mine rehabilitation, revegetation.

Jan 1, 1986

By Kumar M. Lyer

The channel reactor for ferrous and nonferrous processing has been modeled as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength submerged gas injection. A composite model has been developed which describes the mass transfer between the two liquid phases, including the transfer of minor elements. The residence time for the matte droplets in the matte/slag emulsion is compared with the settling rates for the matte droplets in the slag to determine their relative importance in the mass transfer between matte and slag. The governing equations for mass transfer have been developed using correlations for the mass-transfer coefficients in the continuous and dispersed phases. An application of this scheme to a typical copper smelting system is presented.

Jan 1, 1993

By W. Z. Rogers

U.S. feldspar output sold or used in 2005 was an estimated 760 kt (838,000 st), valued at $44 million free-on-board plant. This was below the 2004 volume and was the second year of decline in a row. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures and fiberglass insulation requiring feldspar. Shipments of glass containers were about the same as in 2004. Imports of ceramic tiles and plumbing fixtures continued to increase, taking the place of U.S.-produced goods and the feldspar required to make them. For 2005, 80 percent of the ceramic tiles sold and 50 percent of the plumbing fixtures sold in the United States were imported. Since 2000, manufacturing plant closures in the plumbing fixtures industry have reduced the demand for feldspar and feldspar-silica mixtures by 100 kt (110,000 st). Increased demand from the ceramic tile industry has partially offset the lost volume.

Jan 1, 2006

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

By E. T. Turkdogan

Jan 1, 1962

By T. K. Matthews

Minerals are mined as a one-time crop, and the processing of one ton of ore results in there being one ton less to be recovered from the deposit. Although some minerals occur in greater abundance than others, they are to a greater or lesser degree exhaustible. Depletion Allowances One of the distinctive features of the mineral industries is the allowance for depletion. The depletion allowance is a much maligned and misunderstood principal of our tax structure. Although imperfect in design, it has nevertheless served as a constructive incentive for the development and expansion of the minerals industry.

Jan 1, 1969

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

THE papers by G. F. Loughlin and I. A. Ettlinger discussed the distribution of formations and ore-bodies in two of the main mining districts of the Southwest. The convergence of the deeper orebodies at Cripple Creek points to their common hypogene ori-gin, as do the occurrences of the copper ores of, central Arizona. E. L. Bruce described the areas in southwestern On-tario around Red Lake and Woman Lake, another prom-ising gold district. Of special interest was a series of lantern slides showing the use of power-driven boats and of hydroplanes as means of transportation. Within a few years, no doubt; such devices will revolutionize the mining industry and reconnaissance mapping in these relatively inaccessible areas. Much interest was evinced in the paper by J. W. Finch on "Sedimentary Metalliferous Deposits of the Red Beds." It was written as a caution to people at-tempting to mine these deposits. The discussion of the chemical equations presented in the paper brought out the fact that a large amount of study of such ores is necessary before we shall be able to write equations to explain their formation. Especially pertinent were the discussions by David White as to the relation of decay-ing plant tissue to metalliferous deposits and the color of sediments; also the point brought out by T. S. Lover-ing that chemical compounds produced by bacteria may greatly affect the deposition and reorganization of sedi-mentary metalliferous deposits.

Jan 3, 1928

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

The accurate estimation of ore reserves along with capital and operating costs are two key components to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by improper estimation of ore reserves. The accurate estimation of ore reserves for any deposit relies heavily on understanding its geology and underlying assumptions unique to the estimation techniques being used. The assumptions unique to commonly used traditional and geostatistical reserve estimation technique will be reviewed. The shortcomings of the estimation techniques and their possible impact on a given project's economic outcome will be discussed. The latest developments in geostatistics in overcoming existing reserve estimation problems will be presented.

Jan 1, 1994

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By H. Henein

Atomization provides many advantages in processing such as rapid solidification and near net shaping. Two atomization techniques will be compared and contrasted in this presentation: Single fluid atomization techniques such as Impulse Atomization (IA) and gas atomization. The characteristics of both processing approaches will be presented. Results in powder structure, size and size distribution as well as microstructure will be discussed. A comparison of spray formed ingots carried out using both techniques will also be presented.

Jan 1, 2007

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

Agenda ?The Context ?The Challenge ?The Solution ?Benefits and lessons learnt from pilots ?Next Steps The Context ?Facilitate management decision making process by supporting the development of value/risk based business cases. ?Large scale investments by extractive industries are expected tobring broad-based benefits to local communities (e.g.: health, education, jobs, infrastructure) ?Investors continue to expect the demonstration of social performance?Specific interventions bring direct value to companies (e.g. skills development) ?Social Investments are key to protecting a company?s license to operate ?Quantifying the value of these investments and planning accordingly, however, has long posed a challenge for the extractive industries and community development practitioners

May 1, 2011

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016