Search Documents

By E. Cortese

PHOSPHATE occurs in many places in Egypt,. in two main zones: one in Upper Egypt, along the Nile Valley, principally on the right side, and one near the Red Sea coast. In the Nile zone, the principal layers of phosphate rock are to be found: in the mountains east of Mahamid (right side of the valley); in the hills near Sibaiya, also called Sebaieh (both sides); in the hills of Agula, Hagaza and Gurn (right side); and further on, along the cancel road leading from Kena to Kosseir, a few miles east of Legheita's Oasis. Following, that track, after, having crossed the watershed, underlain by rocks like granite, serpentine, porphyry and diabase, one comes again to the Cretaceous formation containing considerable quantities of phosphate, at Gebel Duwi, Gebel Nakheil and Gebel Kosseir El Kadim, not far from the coast. More to the north, in the hills near Safaga Bay (Um El Uettat El Wasif) is another rich bed of the same formation. There are reports of phosphate existing near Suez and in the Sinai peninsula, and possibly some other zones can be traced or discovered in the future. The mines are well developed on the right bank of the Nile at Sharawna (near Sebaieh Station) and along the Red Sea coast, at' Safaga and near Kosseir. Prospecting work has been done at Gebel Duwi, Gebel Gurn, Agula, Hagaza, and near Mahamid. The phosphatic formation in Egypt is quite variable, not only from place to place, but even within small areas. The phosphate is all of Cretaceous age, as is proved by the fossils found in it. It is considered to belong to the Campanian or, more appropriately, to the Maestrichtian series. The principal fossils are: Alectryonia Villei Coq. sp.; Roudereia Auressensis Coq. sp.- R. Drui Mun. Chalm.; Trigonoarca multidentata, Newton.; Cardita libyca, Zittel; Libycoceras Ismäely, Zittel; Nautilus sp.; Ancystrodon libycum Dam.; Corax pristodontus Ag.; Lamma biauriculata Zittel sp. Above the Maestrichtian beds, we have the Danian series, unconformably covered by Lower Eocene beds. Under the phosphate is a grayish marly clay, and beneath this, bluish-gray scaly shales resting on the Nubian sandstone (Santonian).

Jan 2, 1918

By Gilbert Francklyn

The requirements of coals for the manufacture of coal gas, water gas and producer gas will be considered sparately and a short description of each gasmaking process will be given. In this report the term "gas coal" is confined to coals suitable for the manufacture of city gas in horizontal, inclined or vertical retorts. The report does not refer to coke-oven practice.' Briefly, the process of manufacture consists of distilling the coal at high temperature in an externally heated retort out of contact with the air. The products of distillation, consisting of gas, tar, ammonia, etc. are collected and purified. The residue consists of coke, which is removed from the retort at the end of the carbonizing period. To supply the heat required in the process, a portion of the coke produced is converted into producer gas, which is burned under the retort settings. Qualities of Gas Coals The chief qualities that coal must possess in order to be classified as a gas coal are as follows: 1. Gas Yield.—The coal must be capable of yielding gas in sufficient volume and of a satisfactory quality. The yield depends considerably upon the temperature of distillation; a higher temperature will give a larger yield of gas, but the qualit,y of gas (now measured by the British thermal units per cubic foot) will be lower, while a lower carbonizing temperature will give less gas of higher heating value. The true measure of the yield is the number of British thermal units produced in the gas from a given quantity of coal. This number is obtained by multiplying the cubic feet of gas from 1 lb. of coal by the British thermal units per cubic foot of gas; it is called B.t.u. feet per pound. It is found that the

Jan 1, 1930

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

By J. Guzman

Introduction The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km' (386 sq miles) in and around the Carlin Trend and own all or part of I6out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output. The same incentives produced even more spectacular exploration results. In each of the last five years, net additions to reserves and resources outpaced current production by substantial margins. These facts demonstrate the spectacular past prospectiveness of the Carlin Trend and the success of focused, multi-disciplinary exploration methods that made it possible to more than offset the recent accelerated depletion of gold resources. However, is this situation sustainable? How long can the mining companies along the Carlin Trend keep on finding resources faster than they deplete them? These are some of the questions that motivated this study. The authors have not quantified the future potential for gold exploration in the Carlin Trend nor established a deposit discovery path. But strong indications were discovered that the [ ] Carlin Trend remains a relatively immature exploration district and that the potential for significant new discoveries is high. Methodology and data The approach chosen to address the above questions was simple. The authors compiled deposit size data, measured in contained ounces of gold resources, for all known deposits along the Carlin Trend (Table 1). The resource information was obtained by adding cumulative historical production (adjusted for mining losses and metallurgical recovery) to 1989 year-end published resource inventories. In a mature exploration area, where most deposits have been discovered, this distribution would be expected to approximate lognormality and would plot along a straight line on a lognormal probability scale. This result was found in previous work by Allais (1957) and recently confirmed by Cox and Singer (USGS, 1986) in regard to various types of mineral deposits in several regions of the world. It was also found to hold true for oil and gas pool size distributions (Arps and Roberts, 1958; Kaufman, 1962; McCrossan, 1969). [ ] The data used were compiled by Newmont Exploration geologists. The purpose of the study is to make inferences about the underlying geologic processes in the district and the maturity of the exploration effort. Therefore, deposits were not classified according to ownership but according to geologic occurrence as known from current information. Newmont's Post and Barrick's Goldstrike and Betze deposits, for example, are shown as a single occurrence to reflect the actual geologic setting. The cumulative frequency distribution of deposit sizes was plotted on lognormal probability paper (Fig. 2). The abscissa shows the cumulative fraction of deposits at or below a certain deposit size and the ordinate shows the deposit size in thousands of ounces of contained gold resources.

Jan 1, 1992

Depending upon the probability one assigns to project go-ahead, up to $10 billion (1978 figures) could be required for resource based projects in Australia in the next decade. In the past major resource projects were readily financeable against sales contracts. In the future the complexities imposed by such matters as political risk, inflation, currency movements and environmental and other socio- economic considerations on project development costs and returns may require a different approach. This paper addresses itself to the ramifications of providing development finance for resource based projects in the future - and in particular examines such factors as project completion guarantees, sales contracts, protection against exchange rate fluctuations, interest rate structures and debt/equity ratios as each relates to the provision of finance. TABLE OF CONTENTS SECTION 1 : Introduction SECTION 2 Factors Affecting Project Financing in the Next Decade SECTION 3 Some Aspects of Financing New Projects in Australia in the 1980's Conclusion

Jan 1, 1979

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981

By Dirk van Zyl, Lysa Morishita

Mining companies are increasingly approaching the social aspect of sustainable development within the rural communities that neighbour their projects and operations. Rural community engagement requires significant effort and resources, and it can be extremely challenging for mining companies to earn and sustain social capital. The focus on rural, proximal community engagement is not to be understated and has led to significant benefits in many communities. However, opposition to mining projects is often exhibited in urban environments, where there may be potential for mining companies to gain social capital with relative ease. Cities tend to have existing frameworks for community engagement and public activation, such as annual parades and festivals, that make it easy for a mining company to provide financial support or value-in-kind. Local organizations and community groups can achieve the same amount of engagement in an urban environment with significantly less effort required from the mining company. By applying simple marketing principles to community engagement strategies, corporations can increase awareness for their business and encourage city residents to think critically about the origin of resources. Unlike many corporations, mining companies are not marketing or selling products to individual consumers. From this arises the opportunity for a company to use marketing to promote other positive initiatives and, as such, connect their brand with positive messaging thus earning social capital. This may lead to a wide variety of secondary impacts including benefits to recruitment efforts, increased political support, and positive media coverage. This paper explores these matters with special reference to Vancouver, BC, Canada and the mining companies Teck and Goldcorp.

Jan 1, 2017

By P. Zarate, M. Peart, T. Bhambhani, D. R. Nagaraj

More than 50% of all the molybdenum produced in the world is a by-product of copper production. A bulk Cu-Mo concentrate is first produced, which is subsequently separated into Cu and Mo concentrates. The Cu-Mo separation circuits rely on the use of inorganic Cu sulfide depressants such as NaSH, Na2S, and Nokes, which are hazardous, and sometimes require very large dosages for effective depression. Synthetic polymeric depressants are safer and more efficient, and are now being used on the plant-scale. Data presented in this paper demonstrates that these polymeric depressants can replace 50-90% of all the NaSH in Cu-Mo separation at a fraction of the NaSH dosage. In this paper we provide an overview of the mechanistic and practical aspects of the Cu-Mo separation with inorganic depressants and polymeric depressants. Important practical aspects include depression dynamics (related to conditioning time and rate of depression), optimum pH for effective separation, the role of pH modifiers such as lime and NaOH, and the effect of flotation gas on the efficacy of the separation. Using nitrogen as flotation gas, the NaSH consumption can be reduced by up to 95% by using a small amount of polymeric depressant. The experiments with conditioning time demonstrate that there is a significant rate component to the depression mechanism with NaSH, which is absent for the polymeric depressant system. This has important implications in the effective use and application of the depressant. It is also demonstrated that the pH modifier type (NaOH or Ca(OH)2) has no significant effect on separation efficiency and Mo recovery (i.e. Ca2+ ions do not depress MoS2 in the Cu-Mo separation).

Jan 1, 2014

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By W. J. Nelson

Detailed underground geologic map- ping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Company, which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium- to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular-bedded limestone, and (4) fine-grained, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sand- stone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults of small displacement, "slips" and clay dikes, and limestone "bosses." Less stable roof and wet con- ditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that inter- sect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural patterns apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof sup- ports. Drilling also is useful In locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1980

The accuracy of an ore reserve is only as good as the geologist's understanding of the deposit. The methods that are applied to resource and reserve estimation reflect that understanding. At the Olympic Dam copper-uranium-gold deposit in South Australia, evolution in the understanding of the controls on mineralisation coupled with the changing demands of the project have led to changes in the approach to reserve estimation. The project has moved into a phase where detailed stope mining reserves are now required as distinct from global ore reserves. The complex nature of the mineralisation and the large amount of data demand that all available information be readily accessible in a flexible format. To enable the selective manipulation of geological and assay information and its characterisation, a relational database has been developed. For reserve calculations themselves, initial computations were based on a system derived from that used for the Kambalda nickel orebodies. The Olympic Dam system differed mainly in the use of statistical analyses in the estimation of grade instead of the previous polygonal area of influence weighting method, Three dimensional weighting techniques are now being used for local reserve estimates. Flexible facilities for raw data handling combined with grade estimation techniques which are commensurate with the mine geologist's understanding, produce detailed gridded and contoured ore zone models suitable for reserve calculations and stope designs.

Jan 1, 1987

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By J. J. Antony

As the first wave of precious metal heap leach closures and reclamation projects occur, a number of companies are being hit with costly surprises. While this paper refers specifically to U.S precious metal projects, it could be conceptually directed at copper leach operations and acid rock drainage (ARD) problems on an international basis. ARD is Mother Nature's version of heap leaching, only with different products and timing. Although many precious metal deposits tend to be small in comparison with some base metals systems (porphyry copper deposits), adjacent or nearby discoveries have extended the operating lives of numerous precious metal mines. Now, depleted reserves, several years of relatively depressed precious metals prices and some properties with technical difficulties have resulted in numerous mine closures. As a result, our industry is getting a diverse and comprehensive initial look at mine closure and final reclamation. The situation has been further complicated by the evolutionary trend in regulations and their enforcement and increasing public and political awareness of all environmental issues. Concurrent (proactive) vs. deferred (reactive) reclamation and a realistic early appraisal of ultimate reclamation and closure requirements, not just regulatory compliance, need to be a part of project design. The U.S. and Canada are the current fertile testing grounds and have set the design, regulation and closure standards for the next wave of operations in Latin America, the CIS (?), etc.

Jan 1, 1994

By E Drueppel, M Mistry, J Pateiro

As mining undoubtedly influences the natural environment future challenges of copper ore mining are minimisation of land use in area and duration, proper land rehabilitation as well as tailings management. One possible solution to avoid these negative impacts could be the application of underground mining with backfilling tailings compounds. This approach would definitely increase the production cost. Against this background the project analyses the influence of an æecologically satisfyingÆ copper ore mining on world market prize and demand as well as on the environment. In the project 261 copper ore mines accounting for 98 per cent of world copper production have been examined. After modelling a backfill plant, analyses of applied backfill techniques were conducted. Afterwards a method of cost estimation was developed and then the backfill plant model was applied in three case studies. The results were transferred into scenarios. The work closes with a short discussion and gives an outlook to forthcoming research. The results presented in this work have been generated within the Collaborative Research Center (CRC) 525 entitled æResource-orientated view of metallic raw material flowsÆ. This interdisciplinary project was established at Aachen University of Technology (Germany) in 1997 and is funded by the Deutsche Forschungsgemeinschaft (DFG). The long-term goal of this research program is the identification of options for the resource-sensitive supply and processing of metallic raw materials. In order to address the sustainable development challenges facing the metals and minerals industry an integrated resource management system is to be developed and tested for important metallic raw materials. Case studies for aluminium and copper are being conducted by the CRC 525 in order to provide useful and efficient tools for decision makers over the entire life cycle of these materials.

Jan 1, 2003

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By Dalton. J. L., H. P. Dibbs

An account is given of investigations into the application of two neutron methods to the on-line analysis of slurries. One deals with the application of the neutron moisture gauge principle to the determination of the water content of iron oxide slurries, and the other with the application of gamma radiation from thermal-neutron-capture to the determination of the composition of aqueous slurries of iron oxide, copper oxide, zinc oxide and sulphur. Linear relationships were found between the composition of the slurry and the neutron count-rate in the first study, and between the slurry composition and the prompt-gamma-ray count-rate in the second study. A mathematical relationship has also been developed which relates changes in the prompt-gamma-ray counts from hydrogen to changes in slurry composition.

Jan 1, 1973

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By David Newman

Landslides and soil creep often occur with varying degrees of severity on steep slopes within Southern Appalachia. Ground movement may take place over years with subtle changes in topography and vegetation or it can occur rapidly in response to water inflow or disturbance at the toe of the landslide. Although the ground movement typically is restricted within the soil and colluvial layers, failure can extend into the weathered rock zone. Certain areas of Appalachia are described as "slide prone" because of historical precedent. To develop a profile of "slide prone" areas, the strength and physical properties of the soil and colluvium, topography, groundwater and surface water runoff, present and historical land use, and any surface disturbance are examined in detail. These attributes are useful in determining whether an area is potentially unstable before surface development including construction, logging, or mining. Recommendations are provided to avoid initiating ground movement concurrent with mining operations.

Jan 1, 1998

By T. C. Rao

The quantum of coal fines below 6 mm in run-of-mine (ROM) coal has been increasing due to progressive mechanization of mining methods which has created a substantial incentive, worldwide, to develop suitable fine coal beneficiation techniques. The majority of the efforts have been directed toward reduction in ash/sulfur contents in clean coal. The beneficiation techniques may be broadly grouped as those based on specific gravity and surface property. The processes, which use heavy medium cyclone, water-only cyclone, concentrating tables, and spirals, belong to the former group while the latter group encompasses froth flotation, column flotation, oleo- flotation, and oil agglomeration. In almost all the gravity based techniques, it has been noted that a classification step prior to beneficiation is essential for effective treatment. In general, the effect of design and process variables on the performance of these units and also the quantification of the processes have been the main areas of research and development. In froth flotation, efforts throughout the world have been mainly to understand the effect of variables and to optimize the process. Quantification of the process has been attempted through kinetic studies and mathematical modeling. The efforts have led to the development of new reagents, machine designs, and flowsheets for a specified objective. The attempts so far with the column flotation and oleoflotation processes have indicated a great potential. Extensive R&D efforts are in progress to understand as well as to commercialize the processes. The efforts in the oil agglomeration process have been toward substantiating the inherent merits of the process by developing cheaper bridging liquids and technology to recover and reuse the oil to make the process commercially viable. Modeling of the process has also been attempted to predict the yield and size distribution of the agglomerates. This paper reviews and summarizes the recent developments in the science and technology of fine coal beneficiation processes. The current trends in R%D efforts for these processes are also highlighted.

Jan 1, 1987

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019