Search Documents

By R. R. Wells

As a part of the strategic minerals program of the Bureau of Mines, nine chromite-ore samples were obtained during the period 1949-56 from mines in the vicinity of Red Mountain, near Seldovia, Kenai Peninsula, Alaska. This report summarizes the results of beneficiation studies of the samples at the Bureau's Juneau, Alaska, and Albany, Oreg., laboratories. In general, the ores were found amenable to concentration by gravity methods for producing concentrates that assayed over 48 percent chromic oxide. Intimate association of chromite and gangue minerals, however, necessitated fine grinding and limited the amount of chromite recoverable. Recovery of chromium in concentrate that assayed 48 percent chromic oxide or higher ranged from approximately 20 percent for low-grade ores (10 to 12 percent Cr203) to more than 95 percent for 1 high-grade sample (42 percent Cr203). The iron content of the chrome-bearing mineral -hence, the chrome/iron ratio of finished concentrate -appears to vary with the grade of the ore. Concentrates made from high-grade ores had chrome/iron ratios as high as 3.1:1; the concentrates from low-grade ores, however, had chrome/iron ratios as low as 1.8:1.

Jan 1, 1957

By Ivan Van Herpe

"ABSTRACT NOT AVAILABLEPresentation"

Jan 1, 2000

By T. Plikas, T. Porretta, M. Al-Dojayli, B. Pretorius, J. Woloshyn, H. Ghorbani

"Water-cooled ducts represent an integral part of high temperature off-gas systems in metallurgical processes. Typically, off-gas enters these ducts at significantly elevated temperatures; therefore, water cooling may be required to maintain the duct skin temperature within allowable design limits. These off-gases are typically of high mineral content that could lead to dust buildup, and there is a possibility of slag buildup / molten metal splashing. Therefore, dust cleaning provisions may be necessary in order to remove or minimize accretion on the duct wall, which could otherwise impact the water cooling and the system process efficiency. These ducts may have complex geometry and experience a wide range of loading, including gravity loads, water and gas pressures, cyclic thermal loading and dynamic impact forces. Consequently, the thermo-mechanical assessment of such water-cooled ducts is critical and requires consideration phenomena such as high temperature gradients, potential nucleate boiling, thermal ratcheting and fatigue failures. Such assessment is not comprehensively covered by design-by-rule design codes and guidelines due to its complexity. This paper presents a successful implementation example of design-by-analysis methodology to improve the design and extend the life of a water-cooled furnace transition duct using Computational Fluid Dynamics (CFD) and Finite Element Analysis (FEA).INTRODUCTION Water-cooling represents an important part of high temperature off-gas systems in metallurgical processes. Typical temperatures of the off-gas in the furnace uptake are in excess of 1400°C, and thus there is a need to maintain the water-cooled duct and jacket skin temperatures within their material allowable design limits. Water-cooled channels have been used effectively in arc furnace roof design (Sosonkin et al., 1972; Smolyarenko and Khainson, 1988) and other furnaces as well as in furnace fuming jackets (Scholey et al., 1994). The design of these systems was based on one-dimensional analysis to ensure sufficient cooling is available under extreme furnace conditions (Smolyarenko and Khainson, 1988; Scholey et al., 1994). With advancement in furnace and fuming system designs, water-cooled duct designs have become more complicated in geometry. Numerical techniques, such as three-dimensional fluid flow and heat transfer modeling, are therefore needed to more accurately calculate water velocity, temperature and convective heat transfer coefficients in the water-cooled channels (Haywood et al., 2002; Henning et al., 2010). This is of particular importance around geometric corners where stagnant water flow may lead to local nucleate boiling at the critical heat flux, causing hot spots (Bergman et al., 2011). High wall skin temperatures increase the risk of failures due to thermal stresses as well as increasing corrosion rates (Gelfi et al., 2012), leading to costly equipment downtime and potential safety risks."

Jan 1, 2017

By C. R. Boyd

The region to which I have the pleasure of calling your attention, though limited in area, is remarkable for the quantity and purity of its mineral deposits, and in these respects it would be difficult to find its equal anywhere. IRON ORES. The red and brown hematites, pipe ore, and semi-magnetites, from which is made in charcoal furnaces the highest quality of iron for car-wheels, extend through the counties of Giles, Montgomery, Pulaski, Wythe, Smyth, Washington, Bland, Tazewell, Russell, Scott, Lee, Floyd, Carroll, and Grayson, Virginia, and run over into Ashe County, North Carolina. One locality of semi-magnetite, in the centre of the great Giles County basin, has in sight, by actual measurement, 50,000 tons of ore, which, according to Prof. Fesquet, contains 69.74 per cent. of iron and no phosphorus. In the great brown-ore belt, which passes through the counties of Montgomery, Pulaski, Wythe, Smyth, and Washington, there is an extraordinary deposit of more than a million tons. A small section of this very long vein, on Cripple Creek, in the County of Wythe, yields an ore which, analyzed by Mr. James Aumann, gave the following results: Metallic iron,........58.15 Water,.........12 96 Alumina,........2.32 Silica,.........1.09 Phosphorus,.. none. At one point towards the western end of Red Land Mountain, in Pulaski County, New River section, I measured a body of ore in this belt which will yield, to a depth of 150 feet, over 8,000,000 tons, and the deposit extends far below the 150 feet measured at the upper part. Again, at Rich Hill, near the mouth of Reed Island Creek, these veins show extraordinary surface development, giving an ore of very great purity. At numerous places, also, in the counties of Giles, Bland, Tazewell, Russell, Scott, Wise, and Lee, these brown and red iron ores are exposed in such vast quantities as to baffle both description and measurement. That of Chestnut Flat, in Giles County, back or west of the Angel's Rest Mountain, is an easily reducible ore, blood-red when crushed, of which there are fully 300,000 tons in sight. Its analysis is as follows :

Jan 1, 1880

By Claudio Marcio de Araujo

O trabalho apresenta o estudo e resultados da aplicação do dessulfurante micronizado Puresteel-1000, seus benefícios, economia e melhoria do processo de dessulfuração. Objetivando redução de custo e manutenção nos parâmetros operacionais a CSN desenvolveu junto a um fornecedor um dessulfurante a base de CaO que favoreceu o atendimento com redução de custo .A metodologia utilizada para o trabalho foi à avaliação do sistema produtivo da EDG-CSN, e o estudo de solução para o processo apoiado na revisão bibliográfica do tema. A implantação da aplicação do dessulfurante micronizado Puresteel-1000 obteve para a CSN ganho através da redução de custo de aproximadamente 30% no custo do dessulfurante, mantendo os mesmos parâmetros operacionais.

Jul 29, 2018

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By W. J. Adams

It is recognized that within life cycle assessment that the eco-toxicity potentials (TPs) derived for metals require additional research to improve their reliability. Current models used to develop TPs do not include important fate process for metals such as speciation and bioavailability. Toxicity potentials are standard values used in LCA to enable a comparison of potential toxic impacts between substances. Huijbrechts (2001) calculated toxicity potentials for 181 substances utilizing the USES model for six impact categories, i.e. freshwater aquatic ecotoxicity, marine aquatic ecotoxicity, freshwater sediment ecotoxicity, marine sediment ecotoxicity, terrestrial ecotoxicity and human toxicity (not considered here). Marine ecotox potential for metals is typically high using this approach, whereas most open ocean metal concentrations are very low. A sensitivity analysis of the USES-LCA model was undertaken using copper as an example. Results indicate: fate processes on the global scale are driving the marine water and sediment TPs for copper most; the second most important fate parameter is sedimentation from the water and burial in deep sediment layers; inclusion of speciation and bio-availability processes would be very beneficial; more accurate estimates of input parameters should be used, and the PNECwater and PNECsediment and all partition coefficients for metals should be updated in the model.

Jan 1, 2007

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Dallas Bienhoff

Boeing Study Team Participants Andrew Daga & Associates American Aerospace Advisors Hamilton Sundstrand Harris Honeywell ILC Dover Lunar Transportation Systems Oceaneering Orion Propulsion SICSA Thin Red Line USA LSSCA BAA Topic 2: MFHE Definition Minimum Functionality Habitation Element Deployable Habitat DHE Update The Path to Growth

May 1, 2013

By S Kowalczuk, S V. L Barrett

The potential for adverse surface settlement during tunnelling in soil and rock poses a significant risk to the successful completion of any tunnelling project. Undesirable ground movement may lead to unacceptable level of damage to surface infrastructure, buildings and the environment, resulting in safety concerns as well as causing significant delays and costs to a project. One of the empirical methods which is commonly used to predict surface settlement in the early stages of a project’s development is the volume loss approach as described by Mair, Taylor and Burland, 1996. This method was developed for use in soft ground; however it has also been applied in weathered and soft rock to provide an initial indication of potential surface settlements along a proposed tunnel alignment. This paper presents some initial thoughts on the use of this method in weathered and soft rock and the associated limitations which need to be taken into consideration when interpreting the results. This includes complex weathering profile cases where the strength and stiffness of the ground does not necessarily increase with depth.CITATION:Kowalczuk, S and Barrett, S V L, 2014. Initial thoughts on application of the volume loss approach for estimates of surface settlement due to tunnelling in weathered rock, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 641–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Thomas L, Archibald N

The use of oxygen in the Mount Percy cyanidation circuit was investigated, with the aim of improving recovery. Preliminary batch and plant testwork justified a plant trial, and it was demonstrated that the use of oxygen reduced gold leachable from plant tailings by 12 per cent, and was economically viable. Oxygen is now in permanent use. Other benefits of oxygen in leaching were not proven. There were no savings on compressed air costs and no measurable reduction in cyanide consumption, although HCN levels in the atmosphere above the tanks declined. The possibility exists that more efficient use of compressed air for tank aeration could have achieved similar recovery gains.

Jan 1, 1992

By H. K. Lin

The free-milling ore characteristics of the Fort Knox gold deposit are ideal for studying gold and silver behaviors in various processing circuits without serious interference of sulfide minerals and other refractory factors. A galvanic effect leads to faster silver dissolution than gold dissolution and, as a result, the Au/Ag solution concentration ratio increases through the leach circuit. In the CIP circuit, Au adsorption is more effective than Ag adsorption. The Au/Ag solution concentration ratio decreases from 10.0 to 1.0 as the slurry advances from CIP tank #1 to CIP tank #5, while Au/Ag ratio in the carbon increases from 3.2 to 15.3, as the carbon advances from CIP tank #5 to CIP tank #1. Silver is stripped more effectively than gold from the loaded carbon. The Au/Ag ratio in solution reaches 2.0 in the first 75,700 L of strip solution that pass through the loaded carbon; as the stripping process continues, the Au/Ag ratio in the strip solution increases. In the electrowinning circuit, the Au/Ag ratio in the spent electrowinning solution is significantly lower than that in the electrowinning feed, indicating that Au is more rapidly deposited onto the cathode than Ag.

Jan 1, 2010

By J Ireland, S Rose

The main outcomes of mining grade control include defining the boundary between ore and waste and then categorising the ore according to which stockpile it should be sent. A typical workflow includes using general mine planning software (GMP) – such as SurpacTM, VulcanTM or CAE StudioTM – to create three-dimensional wireframes of mineralisation domains, which are used to flag the relevant samples of interest and constrain estimation during block modelling. Creating the wireframes is a time-consuming process, requiring reasonable software skills, patience and an eye for detail. The interpretations can be subjective; indeed, even the same geologist will give different shapes if presented with the same data at different times. The process can become particularly tedious when trying to carry out updates due to new data. It can also be difficult to test the effect of alternative interpretations or grade thresholds because of the time constraints in production.There are now several implicit modelling tools available, either as standalone programs or as add-on modules to existing GMP. In this paper, the authors develop a workflow using implicit modelling methods to show how grades and geology can be rapidly interpreted to provide effective domains for grade estimation. The paper includes case studies from open pit gold mines. The implicit modelling approach can save several days of interpretation work for each grade control drilling campaign.CITATION:Rose, S and Ireland, J, 2014. Implicit modelling applied to grade control data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006

By James R. Craig

The General Image Processing System (GIPSY) is being employed for the quantitative textural analysis of complex sulfide ores from the Southern and Central Appalachians and for the determination of liberation characteristics of the mineral constituents during grinding. Optical images from a microscope-mounted TV camera or from 35mm film are converted into digital images which are subsequently analyzed by GIPSY, a transportable image processing software package. Properties measured by GIPSY include spatial distribution of mineral constituents, grain sizes, grain shapes, grain orientation and mineral co-occurrences.

Jan 1, 1982

By M. L. Bakker

The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 8 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, in which role it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and platinum group metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003