Search Documents

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first paper5/ dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second dealt with extraction in a mine (Crucible) in which coal was loaded. by hand and in which the rib lines wore long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central hart of Washington County, Pa. , approximately midway between the Montour 10 end Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalizations as appear to be justified.

Jan 1, 1940

By Ronald L. Haxby

This report presents a refractive seismic technique for evaluating the strength of rock within an open pit bench. A concept of correlating rock strength and seismic velocity is discussed and a method of predicting the degree of fragmentation of a pit bench is introduced, Figure 1 shows the area of interests [ ] Most of the work was performed while completing graduate studies at the University of Arizona.

Jan 1, 1967

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By E. H. Dix

The purpose of this paper is to introduce the subject of Stress-Corrosion Cracking at the Joint Symposium of the American Society for Testing Materials and the American Institute of Mining and Metallurgical Engineers. In this Symposium we are concerned with spontaneous cracking which results from the combined effect of high, prolonged stress, and corrosive attack. Stress-corrosion cracking may be considered a specific phase of the more general subject of the effect of high constant stresses in accelerating the rate of corrosion of metal products. The kindred subject of corrosion fatigue in which the life of a metal part under repeated stresses is reduced by corrosive attack is not a part of this Symposium. Likewise "creep," the failure of a metal part by high constantly applied stress, in the absence of a corrosive environment, is not to be included. How- ever, corrosive influences may have more effect on creep failures than is sometimes realized. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium. The penetration by molten metals such as often occurs during tinning or soldering operations, or by mercury, frequently causes cracking when the part is stressed. Strictly speaking this is not stress-corrosion cracking. However, the committee has decided that this phenomenon should be included in the Symposium.

Jan 1, 1945

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By Joseph Pogue

THE, prices of crude petroleum and its derivatives have shown an upward trend from 1915 to 1920, and a downward trend from 1920 to 1923, see Table 1. Over the former period, oil prices were dominated by the rapidly increasing demands and inflation incident to the war and its aftermath, while over the latter period oil prices were influenced at the outset by deflation and then by the conditions of overproduction that have characterized the past three years. The purpose of this paper is to analyze the broader features of the more recent price movements in the petroleum industry and to relate these features to basic economic conditions in the industry. INDEX NUMBERS OF OIL PRICES The analysis and comparison of price movements may be facilitated by converting actual prices into relative prices, or index numbers, with 1913 taken as a base of 100. In this way, the various price groups are expressed as percentages of the 1913 prices and may thus be readily compared with one another or with the average prices of other commodities similarly expressed. Table 1 gives the index numbers representing the average prices of crude petroleum, gasoline, kerosene, fuel oil, lubricating oils, and all commodities. The last named is the index of all commodities as published by the U. S. Bureau of Labor Statistics and .is widely accepted .as the official measure of the general price level. The index numbers of oil prices were calculated by the writer from weekly quotations published in trade journals.

Jan 3, 1924

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By Charles L. Kimbell

While the statistical summary focuses on 1991 data, this update and outlook section draws on information available to the author as of the date of final preparation in early 1993. For all the press notoriety associated with the shift in the Near East crisis from the defensive posture of Desert Shield to the restoration of Kuwaiti sovereignty through Desert Storm, this was not the dominant event governing global economic thinking in 1991 and the first half and more of 1992. From the global perspective, the momentous political changes in the area that was the U.S.S.R. and in the smaller emerging transitional economy states of Eastern Europe will have even greater current and long-lasting effects on world mineral industry activities than the crisis in the Near East.

Jan 1, 1993

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By George Jones

MACHINE mining on the pitch plays an important part in the produc-tion schedule at the Salem Hill Colliery of the Haddock Mining Co. This mine is just outside the city of Pottsville, in Schuylkill County, along the southern border of the Anthracite Region. The entrance to the mine is through a cross-measure tunnel 15 ft. above water level and running north 1500 ft. until it strikes the Rabbit Hole vein, where the machine mining is carried on. The main slope, dipping south, was sunk 1200 ft. in the Rabbit Hole vein with levels turned off at 300-ft. intervals. The vein is from 24 to 30 in. thick on a varying pitch of 20° to 40°. The overburden has differed from 50 to 466 ft., the most recent work having the maximum overburden. Immediately over the Rabbit Hole vein is a seam of soft sand slate from 1 to 4 ft. thick which presents a problem at times because it dis-integrates rapidly when exposed to the air. It will crack up and fall without any audible warning, therefore the workmen must always be on the alert, watching for loose slabs. The main top is sandstone, vary-ing in thickness from 8 to 20 ft. The bottom rock is similar to the top, but is finer grained and subject to a more complete disintegration. The vein has a 3 to 4-in. shelly band along the bottom, and all under-cutting has been done in this soft band.

Jan 1, 1935

By G. Coryell, E. Brack

"Remaining competitive in today's metal markets requires that copper smelters utilize the latest technology offered in process control, data acquisition, and process optimization. State-of-the-art tools like minicomputers, personal computers, and microprocessor based controllers provide real time process information that assist in making proper adjustments to the overall control strategy of an operating plant. The database accumulated by such systems broaden process knowledge, thereby reducing costly errors and plant downtime.IntroductionThe ASARCO Hayden Plant is located approximately 80 miles southeast of Phoenix, Arizona. The plant was commissioned in 1912 for the purpose of smelting copper concentrates from the surrounding mining district. Copper was produced for many years using calcining, reverberatory smelting and copper converting techniques. With the stricter environmental controls of the 1970's, the smelter experienced substantial declines in efficiency and productivity. It became necessary to identify and install a new smelting technology to maintain the viability of the Hayden plant.In 1980, after evaluating several smelting techniques, ASARCO management selected flash smelting as developed by International Nickel Company (INCO). One hundred and thirty-two million dollars was allocated for the project and construction began in 1982. Construction was completed and the new plant came on line in November of 1983."

Jan 1, 1989

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By Morris Cohen, Robert C. Ruhl

The phases in Fe-C alloys over a wide composition range have been studied after splal quenching from the liquid state. Binary alloys containing 0 to 5.1 wt pel C as /cell as a large number of ternary Fe-C-Si alloys with 2.5 to 5.0 wt pct C and 0.3 to 5.1 wt pct Si were attlong those sludied. Olher Fe-C-X alloys, zcilh X being Co, Cr, ,Wn, Ni, and Ru , were also inrestigated after splat quenching. At high carbon contents, a new hcp phase (designaled 6 phase, but different from e carbide) is retained upon splat quenching. The .fraction of this phase varies up lo 97 pcl for a Fe-4.K-1.9% alloy. The composition of the E phase ranges from about 3.8 10 4.8 wt pet C, and the corresponding laltice parameters increase linearly ulith carbon content, while the c/a ratio remains essentially conslc~nl. The E phrtse appears to he a solulion of carbon in E iron, the latler being nornially found only at high pressures. It is deduced that the unit cell of the E phase corresponds to the formula Fe12C3, and llzal il is relaled to tlie ordered slruclures 0.f 6 iron carbide and c iron nilride. The E phase is compared and contrasted to the olher known carbides and nitrides of iron and nickel. An exlrapolaTion of the atomic volume 1,s carhon conlent of /he E pllase lzcts giz.en a neu7 estitnale jor /he alomic volume of E iron, 11.30 cu A, a1 atmospheric pressure and temperature. Other alomic volume relalionships lead to /he co~zpositioti Fe2.iC tor E iron carbide, /he unit cell fortr~ula being -Fe2rClo The E phase undergoes a lulo-slage decomposition upon healing, .forrning firsl rnarlensile plus E carhide, a/ler 1 hr at 140" lo 200°C, slid then ferr ite Plus cementile, after 1 lir a1 330" to 460°C. A1 carbo,l contents between 1.5 and 3.0 LC/ pcl, (he predo.wirzar/t plzase alley quenching is fcc austenite. The retained carbon content of this phase increases with itlcreasing silicon in certain concentration ranges, reaching a maximum of 2.37 wt pct C itz a Fe-2.6C-4.OSi alloy. This is the highest carbon conten1 reLaitled in austenite to date. These high-carbon aus-tenites can be partially tm?zsforttled lo tnartensile hy severe deformation in the temperature range of — 190 to -50°C. TECHNIQUES for splat quenching from the liquid state have been utilized in numerous recent investigations to produce metastable phases in a variety of alloy systems. Among the several ways of splat quenching, the shock-tube method appears to yield the highest cooling rates1-3, 7, 8 and was adopted here. Estimated cooling rates attained in the present experiments ranged from 10' to 10 80Cper sec.' As a part of a research program on interstitial al- loy phases, the Fe-C system was selected for splat-quenching studies. It was hoped that splat quenching would allow high metastable supersaturations of carbon to be retained in solution. Also of considerable interest were the conditions governing the occurrence of the various intermediate phases upon solidification. The alloys investigated included both binary Fe-C compositions as well as six ternary Fe-C-X alloy systems. The known phases in the Fe-C system are summarized in Table I.* Only the ferrite and graphite are ent investigation.14 and is described in detail herein Table II summarizes corresponding data on Fe-N phases, which are also of interest here because of their similarity to the Fe-C phases. EXPERIMENTAL PROCEDURES Alloys were prepared by melting the elements. 99.9 pct purity, in an inert gas nonconsumable electrode arc furnace. The buttons. weighing about 5 g. were remelted twice. were then fragmented. and their interior surfaces were examined for uniformity: if any doubt existed. they were remelted again. Chemical analyses were performed on all the alloys. the accuracy being about k0.05 wt pct. At high temperatures, carbon-containing alloys react with alumina crucibles as follows: If the atmosphere in the splat-quenching furnace does not contain sufficient carbon monoxide the alloy can be depleted of carbon and contaminated with aluminum. Calculations and experimental observations showed that 50 to 100 torr CO partial pressure effectively blocked the above reaction in all the alloys investigated. The splat-quenching equipment in Figs. 1 and 2 provides for evacuation and back-filling with CO-Ar mixtures. The furnace is capable of operation up to 1650°C. and the gettering action of the graphite heating element reduces the oxygen partial pressure in the furnace atmosphere to below 10-5 torr, thus preventing oxidation of the specimens.

Jan 1, 1970

By H. D. Kessler, F. A. Crossley, J. J. Rausch

The titanium-rich corner of the system Ti-AI-V has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the principal method of investigation. TWENTY-SIX alloys in the region 1 to 22 pct A1 and 2 to 11 pct V, and the temperature range 600° to 1200°C, were studied as part of a program on phase relationships and transformation processes of titanium alloy systems. Experimental Procedure Preparation of Alloys—Materials used in the preparation of alloys were high purity Bureau of Mines sponge titanium (103 Bhn), 99.7 pct pure V chips obtained from the Electro Metallurgical Div., union Carbide and Carbon carp., and 99.71 pet pure A1 in the form of granulated shot from Aluminum cO. Of The alloy ingots, weighing l5 g, were melted in a nonconsumable tungsten electrode arc furnace un-

Jan 1, 1957

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.' This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

By John C. Nigro

Bench scale and pilot plant research was conducted using dolomites (CaO,MgO) lime as the basic additive in the preparation of self-fluxed pellets from a typical magnetic taconite concentrate (5.57 S_2). The specific objective of this investigation was to ascertain the viability of the magnesia lime pellets in high temperature oxidizing and reducing atmospheres. Pellet basicity and induration temperature were major parameters affecting fired pellet quality; temperatures ranging from 1,200° to 1,250" C appeared to be the most favorable for production of self-fluxed pellets with basesities (B) above 1.0. Comparison of the mechani¬cal and metallurgical properties of regular (acid) and self-fluxed pellets (B 1.55) produced under similar conditions in a modified grate pelletizing machine showed that the self-fluxed pellets were more resistant to abrasion and to high and low temperature reduction disintegration, an important consideration in commercial application. The Plus 3 mesh Linder index increased from 68 percent (regular pellets) to over 90 percent (self-fluxed pellets). The reducibility and swelling indices of the self-fluxed pellets were found to be comparable to the regular pellets.

Jan 1, 1972

By Plamer D. J, Newman O. M G

The Effluent Treatment System at Pasminco Metals - EZ (PMEZ) was commissioned in December, 1991 and has operated satisfactorily, ensuring that aqueous discharges from PMEZ comply with the Tasmanian Environment Protection Act. The system treats both spills and run-off from the Zinc Plant, and acidic liquor generated in the gas cleaning section of the Sulphuric Acid Plant. The spills and run-off from the Zinc Plant are collected in a large catchment pond. The pond liquor, after partial neutralisation with sodium hydroxide to pH 4, and removal of suspended solids, is preferentially recycled to the Zinc Plant, for example, for washing of residues. Liquor which cannot be recycled, is treated in the Lime Neutralisation Section. The other input to the Lime Neutralisation Section is the acidic liquor from the Sulphuric Acid Plant from which mercury has been removed by contact with aluminium pellets in a fluidised column. In the Lime Neutralisation Section, the liquors are blended and neutralised to pH 10 by the addition of slaked lime. The heavy metals and most of the fluorine are precipitated. The precipitated solids are removed in a thickener with part of the thickener underflow being filtered. Most of the thickener underflow is recycled to generate solids that settle rapidly and filter well. The filter cake is returned to the Zinc Plant for the recovery of contained heavy metals while the thickener overflow is discharged to the Derwent River.

Jan 1, 1993

By John McDonald

THIS report is a continuation of an earlier one with a similar title,1 to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as re-ported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be com-pared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a con-siderable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated.

Jan 1, 1940

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009