Search Documents

By Thomas Egleston

The copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have Well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Heela Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as " mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently to make it pay. The metal is so unifornily distributed throngh these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces, up to many pounds. In one instance, in making an excavation for a cellar of a

Jan 1, 1879

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By Kanaan Hanna

A joint research program between the U.S. Department of the Interior's Bureau of Mines and Cyprus-Yampa Valley Coal Company is being conducted at the Foidel Creek Mine, Oak Creek, Colorado. This program goal is to study the effects of state-of-the-art, high-speed, automated longwall mining on health and safety, and primarily, ground stability under various geological conditions. The Bureau installed an automated data monitoring system, known as the Ground Control Management System (GCMS), to monitor in real-time the effect of rapid mining on pillar and face loading, stress redistribution in and around the longwall panel, and caving characteristics of the roof. The Bureau's GCMS, combined with the company's existing monitoring systems, which include environmental monitoring, a computer programmable conveyor belt system, and gamma ray roof control thickness indicators, has been effectively used to improve safety at the face, increase productivity, and reduce production costs.

Jan 1, 1991

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By Brad Wahlquist

An ex-situ biological treatment system was implemented at a gold mine site in South Dakota. The system removes selenium and nitrate from a mixture of groundwater and surface water runoff at ambient water temperatures. The Applied Biosciences? system replaced a denitrification system that did not perform consistently, did not treat for selenium and required heating of the influent water. Installation was completed in phases starting with the selenium circuit being brought into operation in February, 2002 and the nitrate circuit in March, 2002. System design can accommodate average flows of 380 L/min (100 gallons/minute) and a maximum flow of 1,136 L/min (300 gallons/min). Four cells were designed to remove nitrate from approximately 30 mg/L to below 10 mg/L and two cells were designed to remove selenium from 0.01 mg/L and higher, to below 0.005 mg/L. No pretreatment is required to operate the system at ambient temperatures, which can fall as low as -12C in the winter, and treat water at temperatures ranging between 8C to 16C. Nutrient requirements are met using a sugar based nutrient mixture that includes a balanced C:N:P:S ratio, trace elements and vitamins. Since start up, the system has consistently been in compliance for nitrate and selenium, treating water to below detection limits for both contaminants. This paper discusses laboratory biotreatability testing of a system designed to remove selenium, arsenic, and nitrate and full-scale implementation and optimization of a system to remove nitrate and selenium.

Jan 1, 2003

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By John E. Sweet

THERE have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed ; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steam-engines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the, case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Maxwell Adams

OLIVER C. RALSTON, Salt Lake City, Utah.-We are indebted to these two gentlemen for the work which they have done with the oils derived from sage brush. Their work should not be confused, however, as the work of Mr. Adams deals with steam-distilled oils and that of Mr. Clevenger with destructively distilled oil, largely. In other words, Mr. Adams' oil is probably the original essential oil that existed' in the brush before distillation while Mr. Clevenger's oil not only contained this essential oil but also some products of destructive distillation of the wood constituents. I had noticed the work of Mr. Adams on attempting to separate the various constituents in the oils of some of the Western conifers and had sent to him to ask if he could send me small samples of some of. these pure products. This he very kindly did, and with them included some samples of oil from the common sage brush, whose characteristics he has here described, as well as a sample of oil from the common "rabbit brush." Only the sage brush oil proved of much value for flotation, but it, was very powerful, and I so informed Mr. Adams. Even in amounts as small or smaller than 1/10 lb. per ton of ore, it gave very quick and positive flotation of many ores, with high-grade concentrates and good extractions. It proved to be especially desirable for the flotation of carbonates of lead and of copper which had received an artificial coating of sulphide by treatment with a solution of a soluble sulphide. I also received a sample of crude pyroligneous acid from sage brush prepared by Dr. W. C. Ebaugh, of Salt Lake City. It did not do very good work in flotation, but it is possible that by concentration of this product to obtain the residual tar a good flotation oil might result. This has not been done as yet and I am sorry to see that Mr. Clevenger has not done this. It might be that the dissolved tar, added to the settled tar, would make a total yield of flotation oil higher than the 4 per cent. which Mr. Clevenger feels is a safe estimate. The importance of this point will be seen in the following discussion of the possible costs of sage brush oils for flotation.

Jan 10, 1916

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By Willaim A. Berg

Vegetative stabilization can help meet the esthetic objections and pollution problems posed by mine wastes. However, mine wastes are often unfavorable growth media and special treatments and techniques are needed for plant establishment and continued growth. The establishment of vegetation on mine wastes was the subject of many papers presented at the International Symposium on Ecology and Revegetation of Drastically Disturbed Areas held at Pennsylvania State University on August 3-16, 1969. This paper is a summary of those papers presented at the symposium that dealt with the nutritional and physical aspects of plant establishment on a variety of mine wastes. The synopsis presented is a combination of excerpts from the abstracts, notes on the oral presentations, and rough drafts of some of the papers. The papers will eventually be published in the symposium proceedings.

Jan 1, 1970

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Forest H. Majors

"INTRODUCTION The Brutch sulfur deposits were explored by the Bureau of Mines during the spring and summer of 1944. Old workings were rehabilitated and sampled, test pits and shafts were sunk, and trenches were cut through the surface alluvium.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is due S. R. Zimmerley, regional engineer, and Paul T. Allman, principal engineer, Bureau of Mines, Salt Lake City, for their supervisory aid, and to the metallurgical staff, Salt Lake City, for beneficiation of samples."

Oct 1, 1946

By N. S. Margaris

The vegetation of Mediterranean ecosystems is distinguished by its resistance to adverse environmental conditions, and that is the reason for examining the possibility of growing species of this flora in waste disposal sites (WDSs). The survival and growth of vegetation established at a waste disposal site is dependent to a large extent on the qualitative and quantitative characteristics of the material used in the final soil cover. In the Ano Liossia WDS, where extensive remediation work is under way, three areas were examined, which met certain criteria in relation to the age of the underlying waste and the existence of impermeable material in the final soil cover. Laboratory analyses have determined soil parameters and nutrient and heavy metal content. Alongside this, at all three sites a network has been installed to monitor the qualitative characteristics of the gaseous phase of the soil cover material. The results showed the existence of a soil material containing few nutrients and the prevalence of oxygen-poor conditions, accompanied by large concentrations of CH4, CO2 and H2S, at depths of up to about one meter.

Jan 1, 2002

By H. F. Yancey, O. L. Furse

For several years the Bureau of Mines at its Northwest Experiment Station, in cooperation with the Mines Department. of the University of Washington, has been studying the breakage and degradation of coal. The first phase of the study was devoted to the determination of the friability of many coals of various ranks and comparison of various methods for estimating friability.' A study of the relative ease or difficulty with which various coals are reduced to the fine size required for use as pulverized fuel followed the completion of this work. Baltzer and Hudson2 list twelve research organizations in the United States, two in England, one in Germany and one in Canada that are reported to be engaged on this problem; showing the general appreciation of the need for a simple method of estimating the grindability of different coals. Hardgrove,3 ho has advanced a method for estimating grindability, points out that pulverizer tests of different coals are incomplete and unsatisfactory. He compares such tests to that of a boiler test made without knowledge of the calorific value of the coal. Frisch arid Holder4 also stress the same point. They state that,

Jan 1, 1934