Search Documents

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004

By R. T. Hukki, P. Voutilainen

This paper describes a new apparatus for continuous wet fine-screening. Its preferred size range seems to be from 0.1 to 1 mm. The supercritical trommel screen is a short cylindrical trommel of wedge-bar type construction operated at a speed greater than the calculated theoretical critical speed and at a speed lower than the speed at which particles introduced into it will centrifuge. The paper describes results obtained with the prototype supercritical trommel screen in pilot plant scale. The results point to a high capacity and simultaneously to a high sharpness of screening. Finally, an analysis is presented of the forces acting in screening on a supercritical trommel screen. In the era of high speed, high capacity processing of raw materials the conventional slowly rotating trommel screen is often considered a relic from the times passed. A typical trommel screen is the cylindrical trommel rotated about a horizontal or slanting axis at a relatively low speed. Its screening characteristics are well known. Trommel screens of various types of construction, methods of operation, performances and other characteristics have been described in detail by Taggart.1 The theoretical critical speed of a trommel screen is defined by the same well known equation as that applied for grinding mills: where ncritical = the numerical value of the theoretical critical speed in rpm, D 1 = the inside diameter of the trommel in feet, and D2 = the inside diameter of the trommel in meters. ncritical corresponds also to the centrifuging speed provided that the coefficient of friction f between the trommel surface and the outer layer of the charge is = 1.0. In a general case: From Eq. 2 it is seen that in all cases where f < 1.0 the centrifuging speed of the trommel is greater than the theoretical critical speed. The supercritical trommel screen concerns screening operations within that speed range which is between the theoretical critical speed defined by Eq. 1 and the centrifuging speed defined by Eq. 2, under conditions such that the coefficient of friction f<1.0. It is reported by Taggartl that the optimum speed of a conventional cylindrical trommel screen 36 in. in diam was experimentally found to be about 16 rpm. From Eq. 1, the critical speed of this trommel is 44.2 tpm. The indicated optimum speed corresponds to (16/44.2) x 100% = 36.2% of the theoretical critical speed. The optimum speed range based on information available seems to vary from 33% up to 45% of the theoretical critical value. The trommel screen operated at a supercritical speed: operates at a speed greater than the calculated theoretical critical speed; operates at a speed lower than the speed at which the charge introduced into it will centrifuge; operates within the supercritical speed range in such a way that the coarse fraction of the charge must slide in respect to the inside surface of the trommel; the outer layer of the said fraction next to the screen tends to proceed in the same direction as any selected point on the trommel surface, but now at a lower speed, and indeed at a subcritical speed; allows to a certain degree adjustment of the maximum determining particle size x of the fine product simply by a variation of the speed of the trommel within the supercritical speed range. With increasing trommel speed, finer and finer material only will get the opportunity to find its way into the fine product while the screen opening remains constant. In conventional practice, the low speed trommel is generally used for sizing of coarse and medium coarse material, but seldom for fine screening. The characteristic feature of the product passed through the conventional trommel is that the determining size x of the biggest particle is barely smaller than the nominal size of screen opening. The supercritical trommel screen, on the other hand, is best suited for sizing of relatively fine material. Furthermore, the characteristic determining size x of the biggest particle in the fine product can be substantially smaller than the nominal width of the screen opening or slot. In the trommel screen best suited for the applications

Jan 1, 1965

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By Q. W. Jiang

This paper presents a new process for producing industrial magnesium sulphate using waste water from titanium white plant and magnesium oxide from calcinations of magnesite ore as raw materials. With the laboratory experimental equipment, the waste liquid and magnesium dioxide react effectively at ambient temperature and under atmosphere pressure. Via the press filter, a clear liquid predominately containing magnesium sulphate is obtained. It is further evaporated and crystallized by cooling, separated by centrifuge and dried. Consequently a high quality of industrial magnesium sulphate is achieved as the final product. In the course of process, as the majority of valuable component (SO42-) is recovered in the final product, most of impurities from waste acid is being removed into the by- product. With the simple operational process, it is possible for titanium dioxide plant to resolve the environmental problem completely and benefit from the industrial magnesium sulphate product as well. The filter cakes containing valuable elements such as Mg, S, Fe, Mn, V, Ti are by-product proposed to be used for manufacture of agriculture fertilizer particularly for peanut planting.

Jan 1, 2014

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By Gen-Hua Shi, Richard E. Goodman

In hard, discontinuous rocks, failure modes and stability are controlled to a great extent by the intersection of discontinuities with the excavated surface. We have solved the general problem of finding the shape and size of all blocks formed through the inter- section of any number of joints and excavation surfaces and will demonstrate a simple graphical method for determining which of these is the "keyblock." An example will explain this methodology applied to a simple open pit. The effects of slope curvature in plan or section, will be demonstrated. Finally, we will show how to determine the optimum orientations for the cut slopes. The methodology is based upon a powerful topologic theorem concerning the finiteness of spatial intersections. This paper is a companion to another dealing with underground openings in the Proceedings of the 22nd Symposium on Rock Mechanics (MIT) , July 1981. This paper discusses the rock blocks created by the intersection of discontinuities and excavation surfaces in a rock mass. It establishes principles and procedures by means of which those blocks that are finite and critically located can be identified and described. The main assumptions are the following: 1. The rock itself is assumed to be strong so that the only concern for stability is the movement of rock blocks them- selves.

Jan 1, 1983

By A. Berghezan, E. Bull Simonsen

A simple and general method is described for melting and zone refining refractory metals by induction heating on a specially shaped water-cooled copper crucible. The crucible is the essential part of the apparatus and is placed horizontally. It consists of either a copper plate, or a flattened tube, or of several parallel small diameter tubes all water cooled. The charge lies on the crucible, or whenever possible, is suspended above it. This assembly goes into a transparent quartz tube and the whole is passed through the coil of a radio frequency generator. Vaarious atmospheres can be used. No contamination is detected from the copper crucible. purification is obtained both by selective evaporation of impurities and by zone refining. METHODS of melting and refining relatively large ingots of all reactive and refractory metals as well as some semiconductor materials have been developed in this laboratory during the past several years using induction heating and cold crucibles. These methods are simple and permit the use of a variety of starting materials in preparing ingots of suitable shapes. Among these methods, two are of particular interest. One deals only with the problem of melting without contamination. In this method the induction coil has a specially designed shape and acts simultaneously as heating element and crucible. The second goes one step further, being designed for both melting and further purification of the refractory metals. The aim of this paper is to describe the second method which is of more general interest and of greater applicability to metallurgical problems. A) THE PRINCIPLE OF THE MELTING AND PURIFICATION METHOD As originally proposed by one of us1 the method consists of heating a charge of any refractory metal or semiconductor material to the melting point on a water-cooled copper crucible by passing both the charge and the crucible through the induction coil of a radiofrequency generator. Although both are subjected to the same induction field, one achieves the melting of a refractory metal on a copper crucible even when the refractory metal has a melting point of more than 2000°C above that of the crucible. This seemingly "odd" method works effectively for the following reasons. Because of its high electrical and thermal conductivity as compared with the material being melted, copper can be used as the crucible and kept at a low temperature while the material is heated by induction to its melting point. With water Silver and other highly conducting materials can also be used. If a nonconducting material is contemplated, e.g. SiO or a high polymer, a very thin wall should provide efficient cooling. cooling through ducts in the crucible its temperature can be kept between 40" to 70°C; thus its electrical resistivity is kept low, while the resistivity of the charge increases rapidly as its temperature is increased. B) APPARATUS The crucible is the essential part of the apparatus. It has been designed in various shapes depending on the atmosphere used, whether vacuum or an inert gas or hydrogen. In all crucible designs an effort was made to reduce its volume to "nothing but the cooling water" in order to avoid shielding the ingot from the induction field. In practice it is either a

Jan 1, 1962

By R. O. Burt, R. W. Bruce

"IntroductionGravity concentration, the separation of two or more minerals due to the difference in their relative specific gravity and usually in a fluid medium, is the oldest recorded form of mineral processing.The principles of gravity concentration were known to, and practiced by, the ancients and Hoover's commentary to De Re Meta/lied'' notes many early references.Over the centuries, as direct smelting ores became more and more uncommon, the mineral processing industry developed and along with it many varied methods of concentration. Gravity concentration declined rapidly in importance in the early twentieth century, and it is only in the last decade that its advantages are being re-evaluated.A significant proportion of ores are processed by gravity; a large proportion being in the iron and coal industries<'>, or in the treatment at very high volume of relatively coarse alluvial deposits. The tin dredges of South East Asia and Beach sand plants of Australia are prime examples.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive.Principle of Gravity ConcentrationGravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air.The relative movement of minerals to one another is achieved by a variety of methods. These are: separation in a fluid of intermediate density (heavy media separation); by stratification (such as in jigging); in a flowing fluid (cones, spirals, sluices etc.) and with a horizontal shear (shaking tables etc.)."

Jan 1, 1989

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a &quot;D&quot; welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By R. T. Sorensen

Bench-scale and continuous testing were performed to adapt the anionic process for flotation of calcium activated silica to the fine-grained hematitic-goethitic jaspers from the Marquette range, Michigan. These ores typically contain about 35 percent Fe and require grinding to about 80 to 100 percent minus 400 mesh to insure an adequate liberation of gangue from the iron oxides. A method for removal of troublesome slime fractions without excessive iron loss, by first dispersing the quartz and then selectively flocculating the iron oxides, was evolved in the laboratory and successfully accommodated to pilot plant practice. The efficiency of the flotation process was improved with respect to both reagent usage and concentrate grade and recovery by using the selective flocculation-desliming technique as a pretreatment. The benefits of the combined desliming-flotation procedure were most evident in pilot plant processing. The best tests on two ores yielded recoveries of about 84 percent in concentrates containing 65.1 percent Fe and 4.8 percent SiO2 and 66.2 percent Fe and 3.9 percent SiO2, respectively. These results are in comparison to recoveries about 10 percent lower than the above to concentrates containing 63.9 percent Fe and 6.6 percent SiO2 in the one instance, and 63.6 percent Fe and 7.2 percent SiO2 in the other, obtained by flotation without the prior desliming treatment.

Jan 1, 1967

By J. D. Miller, P. J. McDonough, H. Q. Portillo

Previous investigations have demonstrated the catalytic effect of silver additions in the ferric sulfate leaching of chalcopyrite [ ] The enhanced rate of leaching was found to be due to the formation of an intermediate Ag S film which forms on the Cures2 surface by an exchange reaction Under these conditions, unlike the uncatalysed ferric sulfate leach, the elemental sulfur forms a nonprotective reaction product on the Ag S crystallites As a result, the rate appears to become limited by an intermediate electrochemical reaction in {he Ag2S film rather than by transport through the elemental sulfur reaction product [ ] The reaction rate was found to have a complex dependence on the Ag+, Fe++ and Fe+3 concentrations, but independent of the Cu concentration Electrochemical measurements with a Ag,S-coated chalcopyrite electrode provide further information regarding the nature of the reaction mechanism The kinetics of the rate limiting, intermediate electrochemical reaction are analyzed in terms of the Butler-Volmer equation

Jan 1, 1981

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By C. R. Johnson, R. A. Greenkorn, E. G. Woods

A new method of reservoir evaluation called pulse-testins has been developed for describing formation properties between wells. Pulse-testing utilizes a sensitive differential-pressure gauge at a responding well to measure and record the response generated by a series of flow rate changes (pulses) at an adjacent or pulsing well. Since the pulse-test instruments have a sensitivity of about 0.001 psi, pulses of several hours or less in duration will generate a measurable response in most reservoirs. For this reason, many well pairs can be tested in a short period of time with little interference in field operations. Comparison of pulse-test results to conventional testing methods shows that the pulses obey unsteady-state, compressible-flow theory and thus provide a measure of both transmissibility (kh/µ) and storage (Fch). In additian, the method can be used qualitatively to describe communication across faults and between zones, and direction and tnagnitude of fracture trends. INTRODUCTION To obtain maximum usefulness of new reservoir analysis methods as well as to aid the field engineer in understanding local reservoir anomalies, improved methods are needed to describe heterogeneities in specific reservoirs. Optimum well spacing, equipment specifications, well completion design and especially the economics of pressure maintenance and secondary recovery programs depend on the extent and location of the heterogeneities that affect flow behavior in the field. One method for obtaining a measure of areal reservoir heterogeneity is an interference test. In the simplest interference test. constant-rate production or injection is initiated at one well and the effect of this flow is measured as pressure vs time at another well. Thus, during interference tests the flow characteristics of the formation are determined in situ. Despite their obvious usefulness in reservoir delineation. interference tests have not enjoyed frequent usage. Reasons for this have been the weeks or months required in many fields to obtain a pressure response measurable with conventional gauges, and the interruption of routine field operation during the field-wide shut-in normally required during these long times. Also, only average properties of the relatively large volume of the reservoir disturbed during these long times can normally be obtained — variations in properties between individual wells cannot be delineated. To eliminate these drawbacks of conventional tests, a special reservoir description technique called pulse testing&apos; has been developed. Pulse-testing has several advantages that make it more convenient and practical for field use than interference tests. Valid tests are more certain because use of a series of flow disturbances gives rise to a diagnostic pressure response that can more readily be distinguished from unknown trends in reservoir pressure and other "noise." The time required is only a fraction of that for an interference test because a special, high-sensitivity differential pressure gauge can detect a much smaller pressure change. Variations in properties between individual wells can be delineated because of the relatively small volume of the reservoir disturbed during these short times. Finally, wells other than the pulsing and responding wells do not have to be shut in or carefully regulated.

Jan 1, 1967

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency&apos;s list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Study on the Reasonable Mineral Processing Technology of a Cu-Mo Ore

Sep 13, 2010

By Hayward B. Oblad

The effects of eight independent variables on froth flotation product yield, ash content, and coal recovery were studied using laboratory batch flotation of 0.6 am x 0 coal. The eight flotation variables investigated were air feed rate, pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, collector conditioning time, frother (methyl isobutyl carbinol) concentration, and collector (No. 2 fuel oil) dosage. The two-level Plackett-Burman screening design and the three-level Box-Behnken design were used. Within the ranges studied, air feed rate had no effect on product yield. Pre-dispersion of collector oil, impeller speed, product collection time, initial solids concentration, and collector conditioning time showed only minor effects on the product yield and quality. Frother concentration (mg/L) in the process water and collector oil dosage (g/kg) were shown to be the dominant independent variables in coal froth flotation. Flotation experiments that vary initial solids concentration at constant frother dosage (g/kg) confound the effects of frother concentration (mg/L) and solids concentration. The dominating effects of frother concentration and oil dosage on coal recovery and froth product ash content are illustrated with three-dimensional plots. The relationship between froth product ash and coal recovery is also clearly illustrated by the flotation data.

Jan 1, 1985