Search Documents

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By A. Moyano

The development of the traditional converting process performed in a PeirceSmith or Hoboken converter is limited by the investment magnitude associated to the fulfillment of the environmental regulations. Thus, the continuous converting process rather than a conceptual process alternative is becoming a necessity for a smelter facing limited converting capacity and/or lacking of fulfillment of the environmental regulation with its maximum converting capacity. The objective of this paper is to present the progress of the Codelco continuous converting process evaluated at pilot-scale level when converting solid mattes or white metal into blister copper. These tests allowed for gathering of relevant data to be considered for a new stage of evaluating the Codelco continuous converting at industrial-scale test. The pilot-scale tests were done in a Teniente Converter pilot scale unit at the Codelco Norte Smelter. The results of processing solid copper mattes (65-75% Cu) and producing low sulfur content blister copper with production of a constant S02 gas concentration, and the production of liquid slag with low copper solubility was achieved and is discussed in the present paper.

Jan 1, 2007

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By L. A. Cranson

WHEN I came out of Stanford University in 1922, the out-look for men trained in geology, petroleum engineering, and mining was indeed dismal; in fact, so much so that most of us looked upon our future in those fields as pretty hopeless. Neither our professors nor those men in industry with whom we came in contact gave us any enthusiastic encouragement as to the future of ourselves or the fields we had chosen for our labors. I believe that the attitude of pessimism which saturates everyone about graduation time is lament able and short-sighted, and may often start a young man on his way with an attitude of defeatism. Instead, he should be starting out knowing that he can expect hard work and keen competition, but that the fields of his labours are expanding at an accelerated rate, and that strong, energetic efforts will as always accomplish highly satisfactory results.

Jan 1, 1941

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By J. T. Matson

This paper describing the mining practice at the Pecos mine of the American Metal Co. of New Mexico, a subsidiary of the American Metal Co., Ltd., is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United States. The mine is producing about 18,000 tons per month of zinc-lead-copper ore, chiefly by the square-set and cut-and-fill methods. Costs are given for 1927, 1928, and 1929, the whole producing life of the mine to date.

Jan 1, 1930

By Edgar T. Gregory

A quiet revolution has taken place in the conveyor belt industry, Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry, It wasn't too many years ago that the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Then came the development of monofilament rayon. This material had desirable elongation and elastic properties and was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon. Initially, nylon was considered suitable only for the cross threads or filler threads of a belt carcass. Then technical advancements in heat setting and fabric weave created a major change in belt construction. As a result of these advances the industry was able to take advantage of the full tension strength of nylon cord. Another breakthrough in the use of synthetics was the tremendous increase in adhesion resulting from a chemical bond, rather than the limited physical bond available with cotton. But the advantages of nylon had a more Car-reaching effect, We were able to design a two-ply nylon belt that did the work of a four- or five-ply cotton or rayon belt. A six-ply nylon belt now replaces a twelve-ply cotton elevator belt. Arid nylon resists moisture, acid and mildew, It also has excellent resistance to impact and can be produced with controlled elongation and elastic properties that work to great advantage in reduced-ply belt constructions.

Jan 1, 1971

By Martin D. Larisch, Ronald Damen

The design and construction of temporary working platforms for cranes and piling rigs is a high-risk activity. It requires the careful selection of the appropriate input parameters to obtain the correct load cases, as well as the application of robust and reliable design methods to assess the required thickness and stiffness of the working platform. The document introduces some of the most common and most relevant guidelines for working platform design which are currently used in Australia and New Zealand. The authors will also discuss the basic assumptions and considerations about load transfer from construction plant, debate ground risk, compare the applicability of different design methods for various ground conditions and suggest some common verification methods for working platform certification.

May 1, 2022

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By C. A. Fisher

THE discovery of petroleum in Pennsylvania in 1859 marked the birth of an industry of paramount importance. Spreading from - Oil Creek, this remarkable industry may be said to have embraced the earth in a little more than half a century. Those who made the discovery little realized its deep significance or far reaching influence on our national life. For over sixty years, during which time this nation has created and developed the oil industry to a high state of efficiency and' carried its activities to all parts of the world, we have' at all times been the leaders in the production of crude oil and in the development of its technology. During the unprecedented growth and expanse of the oil industry there has been an increasing dependency of our basic industries on, petroleum, until at present it has become essential to our national existence. To meet the ever increasing demand for petroleum and its products, we have explored, at one time or another, for their oil possibilities, practically all parts of the sedimentary rock area in the United States. Furthermore, detailed surface and, in many places, subsurface studies have been made of all the promising regions; over 640,000 jewells have 'been drilled for. oil since the beginning of the industry; $12,000,000,000 have been spent in this work; seventeen major fields exceeding 100,000 bbl. daily production and more than a thousand minor pools have been opened up, and 8,000,000,000 bbl. 'of oil have been produced, or an amount nearly equal to the estimated future reserves of the United States made in 1921.

Jan 1, 1925

By Lincoln A. Stewart, P. S. Haury

"INTRODUCTION AND RESUME Arizona asbestos mines are the only sources on the American continents of iron-free chrysotile spinning fiber that meets the Navy specifications for asbestos fiber for use in covering electrical cables. Rhodesia normally supplies the bulk of this grade of asbestos at about half the Price of Ari zona spinning fiber. The acute submarine menace in 1942 focused attention on the danger that imports might be cut off and that a sudden demand for greatly expanded production might fall on the Arizona mines to supply the tonnage of this essential material needed for war production.A joint preliminary investigation of Arizona asbestos deposits was made in August 1941 by J. R. Thoenen, senior mining engineer of the Bureau of Mines and A. E. Granger, a geologist of the United States Geological Survey. A more extended investigation of the numerous asbestos mines and prospects, which are scattered over 25 townships of difficult terrain in Gila County, was begun by the senior author in August 1942.The Geological Survey assigned two geologists (Newton Chute and A. F. Shride) a few weeks later to study the geology as an aid in selecting the mines for the Bureau's exploration projects. Six mines were selected for exploratory work because it was desired to prove reserves of ore where production could be started quickly if urgent demand should arise. Acceleration of production is normally slow because of adverse operating conditions. First, the mines are at distances of 35 to 100 miles from Globe, the shipping and supply point, and the roads are few and poor. The mine openings start in steep canyon walls, so that mining supplies usually have to be packed in and the product packed out over 0.5 to 5 miles of burro trail. Second, most of the ore deposits are small, and the ratio of rock broken to spinning fiber recovered is very high, usually exceeding 200."

Aug 1, 1947

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the Purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of Procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937