Search Documents

By R. A. Cattell

Every finding of the year's work, obtained under stress to meet present objectives, contributed to postwar needs, because the very nature and constitution of petroleum and natural gas require that research be conducted along the same general lines whether the results are applied in peace or war. More than 40 reports were submitted to the Petroleum Administration for War and others concerned with (1) evaluation of crude oils to determine their content of aviation-gasoline base stock, (2) evaluation of base stocks for blending with high-octane, synthetically manufactured components, (3) analyses of naphthas to determine their content of various types of hydro-carbons, such as benzene and toluene, and (4) the improvement of quality of marginal base stocks to meet future requirements of aviation gasoline. This upgrading of marginal stocks is being attained by selective distillation and chemical and catalytic removal of sulfur compounds. Asphalts were studied with respect to the characteristics of their various constituents in order to compound them, in the same way that aviation fuels now are being "built" to meet exacting requirements. The work previously initiated to give the industry fundamental data on thermodynamics of hydrocarbons progressed satisfactorily, and the heats of combustion of 10 hydrocarbons in the lubricating oil -range of petroleum were determined. Thermodynamic data requiring highly specialized techniques are so broad in application that their commercial usefulness is not yet fully appreciated.

Jan 1, 1946

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By Mick Lownds, Ruilin Yang

The potential advantages of electronic detonators with accurate timing have been increasingly recognized by the blasting community. However, in comparative blasts the results with pyrotechnic timing are sometimes comparable to those from electronic timing. Statistical variation in blast results is a plausible cause of these observations.

Jan 1, 2011

By D. Harrington

Correct ventilation of underground workings whether in coal or in metal mines consists in establishing such control of air currents that the miners may work in safety, with maximum comfort and efficiency, and without impairment of health; also in controlling the air flow so that the mine workings may at ordinary times be kept reasonably free of harmful gases or dusts, and so that in time of emergency, as when a fire or an explosion occurs, there may with minimum delay be maintained as much or as little air flow as is desired throughout the mine in its entirety or in certain parts of the mine. Control of air flow is the essential point of any mine ventilating system, and is obtained only by the installation of mechanically operated fans, and other ventilating devices such as doors; overcasts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. Much has been written about natural ventilation, and many claims have been made that in specific mines or parts of mines there is sufficient natural air flow. As a matter of fact, there are actually very few if any mines, coal or metal, where natural ventilation creates atmospheres anything like adequately safe or healthful for underground workers even at ordinary times or under ordinary. conditions; and at the time of a fire or an explosion mines depending upon natural ventilation are practically helpless, and are decidedly dangerous for the unfortunates forced to be in them either at the time of the disaster or afterwards when trying to handle conditions arising from the emergency.

Jan 1, 1929

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By William F. Hahn

This project focused effort on three separate areas: demonstration of a low seam longwall illumination system, design of illumination systems for low coal auger miners, and an assessment of machine lighting systems for machinery used to mine low seam coal. Results indicated illumination systems can be purchased by the mine operators of low coal seams. These systems can be supplied with the equipment as a factory integrated system or can be retrofitted to the machine or longwall equipment.

Jan 1, 1982

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By N. L. Piret

In copper smelting minimization of solid waste generation is receiving increased attention with more stringent environmental legislation and lower disposal space availability. Copper smelting slags generally being valorizable, solid waste generation is attributed to the presence in the feed of unvalorizable impurities which do not report to the slag and to the unavoidable formation of contaminated dilute acid solutions which need neutralization. As to unvalorizable impurities, solid waste minimization is achieved by rejecting them in the highest possible concentration. Dilute acid is mainly due to the formation of SO3 in the smelter gases and to the discard of decopperized bleed-off electrolyte. Its generation is substantially lowered by preventing SO3 formation, by converting the dilute acid to a valorizable product, e.g., by thermal decomposition for H2S04 recovery or by precipitation as chemical gypsum, and by suitable treatment of the bleed-off electrolyte for impurity removal. Industrial processes are evaluated and alternatives are discussed.

Jan 1, 1994

By G. M. Hughes, R. W. Dunn

"AbstractCurrently installed an analogue instrumentation devices at Sherritt 's Ruttan Concentrator control. and/ or measure mill tonnages, grind, pH, density , some reagent and slurry flows, and cell levels. On-stream analysis is used to assay the main process streams. The history of development of process control is reviewed from startup to the present stage of selection of a process control computer. A pragmatic approach has been taken to process control to ensure compatibility with the needs and resources of Ruttan. Emphasis is made of the need to have the mill performing well from a mechanical and instrumentation point of view and to have opera tor acceptance of the computer through training. Plans for the computer phase to achieve these objectives are outlined.IntroductionTHE COPPER-ZINC OREBODY at Ruttan Lake was discovered by Sherritt exploration personnel in 1969 and by mid-1973 a 10,000-tpd mine and concentrator were in operation. After a typical startup period , the major mechanical problems in the crusher and concentrator have been resolved. Metallurgical performance is now up to standards forecast in the feasibility study.The cost of the original instrumentation installations, including an on- stream analyzer, was about one million dollars or 4% of the cost of the milling complex. Although there was no intention of using a process control computer until the plant was operating smoothly, it was understood that all instrumentation was compatible with .a computer, but this did not prove to be correct. This paper cover s the development of the instrumentation loops to date and the control strategies that will eventually be implemented through a process control computer."

Jan 1, 1977

By A. Golabchi

Building Information Modeling (BIM) is an increasingly popular method for generating and managing facility information during the life cycle of a building, ranging from facility conceptualization, through design, construction and its operational life. Organizations involved in Facility Management (FM) have the opportunity to use BIM as a knowledge repository to document evolving facility information and to support decisions made by the facility managers during the operational life of a facility. This paper demonstrates the potential of using BIM to develop algorithms that automate decision making for FM applications. The potential of utilizing BIM as an analysis tool is demonstrated through the scenario of HVAC (Heating, Ventilation, and Air Conditioning) system failure in an operating facility. In case of a typical HVAC malfunction today, facility occupants record complaints in a ticketing database maintained by the FM organization. Upon receiving notification of HVAC system failure, facility inspectors visit the location to confirm the reported failure. Upon confirmation, facility managers review building plans and specifications to develop a detailed plan of action to repair any HVAC components suspected of damage. Based on the plan of action, inspectors visit the facility to inspect and, in case of damage, repair the appropriate HVAC system components. These FM practices ? as currently implemented across the industry ? are labor intensive, time consuming, and often rely on unreliable and outdated information. To address these shortcomings, the authors propose an alternative methodology of HVAC fault detection in operational buildings. The authors implement an algorithm that leverages complaint ticket data and automates BIM to determine potentially damaged HVAC system components. Based on the list of HVAC components suspected of damage, the algorithm develops a plan of action for the facility inspectors. Finally, the authors discuss the advantages of the proposed method as well as the challenges of implementing automated BIM-enabled decision making processes in the FM industry.

Aug 1, 2013

By T. Feldmann, G. P. Demopoulos

The feasibility of chloride leaching processes depends on interfacing them with cost-effective HCl regeneration technologies. This paper summarizes the most important findings of research conducted in the past 3 years concerned with a novel process to regenerate high-strength HCl from concentrated CaCl2 solutions at temperatures below 100°C, via reaction of CaCl2 with H2SO4 resulting in the formation of calcium sulfate phases (gypsum, a-hemihydrate or anhydrite). From constant supersaturation semi-batch experiments in pure solution it was found that the crystal growth rate of hemihydrate, and hence the particle size, was influenced by the rate of reagent (Ca2+, SO4 2-) supply to the reactor. Additionally, growth studies of DH in presence of impurities (K+, Mg2+, Sr2+, Ba2+, Fe2+/3+, Al3+, La3+, Y3+, F- and PO4 3-) showed that specifically Sr2+ and PO4 3- are taken up during crystal growth. Furthermore, it was found that decreasing water activity (via different HCl/CaCl2 concentrations) and increasing temperature reduce the metastable life-time of DH and HH by increasing the phase transformation speed. The DH/HH transformation was identified to be dissolution-precipitation based, while HH to AH is a topochemical process. Finally, continuous experiments on bench scale are underway to confirm the feasibility of the process to obtain super-azeotropic strength HCl with up to 9 mol/L (~30wt.%) from 5 mol/L CaCl2 (~40wt.%) solution.

Jan 1, 2014

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By J. K. Whyatt

The Bureau of Mines, under a cooperative agreement with Callahan Mining Corp., measured rock displacement at the 4,7S0-ft level of the 5,100-ft-deep rectangular, timbered Caladay Shaft in northern Idaho. Displacements were measured with multiple-position borehole exten-someters (MPBX) installed 4 ft above the face and timber extensometers (TE) installed with the timber sets. This report presents the displacement data along with preliminary, qualitative observations of rock behavior. The measured displacements showed an instantaneous response to shaft sinking and significant time dependency. The relative magnitudes of displacement measured at the shaft walls were heavily influenced by local geologic structure and distance from the shaft bottom.

Jan 1, 1987

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90° and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1946

By D. K. Marjaniemi

The U.S. Bureau of Mines inventoried and characterized mineral sites and production plants within 200 km of the border in both the U.S. and Mexico. Sources of information included the USBM Minerals Availability System, the USBM Automated Mineral Information System, the USGS Mineral Resources Data System, the Mine Safety and Health Administration Address/Employment File, and the literature. Three hundred seventy-eight major construction material and industrial mineral properties were identified and characterized in the U.S. and Mexican parts of the Borderlands. Sixty-six major metallic mineral properties were identified and characterized in the Mexican part of the Borderlands.

Jan 1, 1996

After considerable input from the mining industry, the Canadian Securities Administrators (CSA) finalised National Instrument 43-101: Standards of Disclosure for Mineral Projects. This Instrument, which became law across Canada on 1 February 2001, applies to all technical public disclosure on mineral projects and requires all technical disclosure to be based on the work of a æqualified personÆ (QP). While the QP is quite similar to the Competent Person in Australia there are important differences when it comes to all disclosure. This paper will summarise the main areas in which the Instrument introduces major changes to Canadian disclosure standards on mineral projects including the role and responsibility of the qualified person; the increased requirements to file technical reports; the incorporation by reference of the October 2000 CIM definitions of resources and reserves and additional rules governing written disclosure of scientific and technical information. In October 2001, eight months after the implementation of NI 43-101, the CSA compiled a list of frequently asked questions (FAQs) and CSA responses to assist mining industry participants and their advisors in understanding and applying NI-43-101. This document has been well received by industry. The CSA plans to update the FAQs when further guidance is requested. Two industry committees have been established to provide the CSA with technical advice on the application of NI 43-101. As recommended by the Ontario Securities Commission/Toronto Stock Exchange Mining Standards Task Force, the CSA has established an external industry advisory committee û the Mining Technical Advisory and Monitoring Committee (MTAMC) û to monitor the application of NI 43-101 and advise the CSA on industry and professional developments. The role of the CSA-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Working Committee on Reserves and Resources is to ensure that the future changes and updates to the CIM Standards can be efficiently and effectively incorporated in NI 43-101. During this first year, the Canadian securities regulators have seen an improvement in the quality of disclosure on mineral projects, which will increase investor confidence in the industry.

Jan 1, 2002

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966