Search Documents

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By Juan Manuel Candia Vargas

"El siguiente trabajo refiere los métodos de explotación empleados en la mina San Antonio de Esquilache por la Compañía de Minas del Perú, considerando previamente los métodos de preparación y desarrollo empleados. Para ello, se describen primero las labores de acceso, constituídas por los socavones de cortada, siendo el más utilizado el ""Farrallón"" que conduce el relleno a los parajes y la explotación de los minerales explotados, mientras que el ""Hardy"" se encarga de la extracción del mineral. Luego están las labores de desarrollo, comprendidas por las galerías y chimeneas sobre veta, donde las primeras son proyectadas a una diferencia de nivel que varía de 30 a 40 metros y a una distancia fija de 30 metros las segundas. La preparación de los tajeos se inicia con el ""desquinche"" de las galerías, al tiempo que se coloca la enmaderación. Por último, se da la explotación por corte y relleno en el que este último está completo antes del rajo."

Jul 20, 1955

By Woodcock J. T, Jackson N

Wattle Gully Gold Mines N.L. of Chewton, Victoria, has decided to replace its present battery plant by a new mill to treat a free milling gold ore, after fine grinding, by concentrating coarse gold in a jig concentrate for amalgamation, and fine free gold and auriferous sulphides in a flotation concentrate for cyanidation. This paper outlines the economic justification and advantages of this step. In a review of the present position at the mine, a history of the company is followed by a description of the ore and its occurrence.Present treatment practice in two separate battery plants is described. Treatment tailings assay 1 dwt/ton gold and a substantial part of this gold is finer than 200 mesh.Experimental work showing how recovery may be improved is discussed and alternative methods of concentrating coarse gold mentioned. It is decided that the most suitable method for recovering gold from the ore is by jig concentration plus flotation.The merits of various flowsheets incorporating these techniques in the existing plant and in a new plant are assessed. It is concluded that there is no advantage in extending or converting the existing two battery plants, and it would be more economical and satisfactory to build a new plant.An economic study shows that for a capital expenditure of £120,000 a new plant could be erected to treat 70,000 tons p.a., working a 5-day week, and return an additional 14.2/- per ton, or £50,000 p.a., in revenue over the existing plant. It is estimated the plant cost can therefore be recouped out of savings inside three years. Probable ore reserves are sufficient to cover this period and additional ore will certainly be developed.INTRODUCTIQNSince 1934, Wattle Gully Gold Mines N.L. has been mining a lode gold ore at Chewton, near Castleniaine, and treating it by stamp milling and plate amalgamation, plus table concentration of auriferous sulphides. In 1954, following two years of unprofitable operation, a rehabilitation programme of all sections of the mine and plant was commenced. In the treatment section, two, major prospects for improvement...

Jan 1, 1959

By P. Forbes

Mining and metallurgical processing companies that have adopted the principles of good environmental management often find it difficult to carry out an environmental assessment that yields meaningful opportunities for improved performance. This topic was investigated by means of a case study of a South African Base Metal Refinery (BMR) producing primarily nickel. A process-based Life Cycle Assessment (LCA) was carried out on the refining process, with the environmental impacts related to the production of reagents and utilities forming part of the assessment. The lifecycle inventory (LCI) was based on plant operating data spanning 31 months of production, from which a baseline environmental profile could be generated and interpreted to indicate the main sources of potential environmental impacts. Consequently, opportunities for improved environmental performance could be identified from the LCA model, which expressly related potential environ-mental liability to specific sub-processes in the assessed industrial operation. The on-site steam plant was found to be the primary source of potential environmental impacts in most of the impact categories considered. In closing, the paper discusses some of the limitations encountered in use of the LCA method. Keywords: life cycle assessment; LCA; life cycle inventory; LCI; base metal refinery; improved environmental performance; environ-mental management systems; nickel refining.

Jan 1, 2000

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By A. D. Schwope, L. R. Jackson, A. M. Hall

In the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of re-crystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. Materials Used in The Investigation Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table I. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871° C in air and hot rolled to % in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hr. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pet reduction) in 6 passes and annealing at 427'C for 4 hr. This annealed wire was then drawn to 0.081 in. wire, (37.1 pet reduction) in 2 passes. Square rod was made by hot rolling wire bars to Re in. rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 346 hr at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°Cf or 3 1/2 hr Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 x 0.268 in. square, annealing for 3 1/4 hr at 538°C and cold rolling to 0.257 x 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hr in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from o.o15+.oz5 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. Effect of Cold Drawing and Tensile Strain on Strength of Copper Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are 6

Jan 1, 1949

By T. Qiu

"The purpose of this study is to investigate the effect of the dosage of sodium hypochlorite as activator on the flotations of depressed marmatite and depressed chalcopyrite, with a focus on activation-flotation kinetics. Four flotation kinetic models were applied to test data using 1stOpt statistical analysis software to estimate the relationships between the maximum flotation recovery rates for the depressed marmatite and depressed chalcopyrite, the flotation rate constants and the sodium hypochlorite dosages. Within the range investigated, the highest flotation performances of depressed marmatite and depressed chalcopyrite were obtained at 2.5 mL/L sodium hypochlorite with zinc recovery rate of 93.8 percent and 3 mL/L sodium hypochlorite with copper recovery rate of 94.6 percent, respectively, after four minutes of flotation. A second-order model with rectangular distribution of flotabilities gave the best fit to test data collected at various sodium hypochlorite dosages. For the highest flotation performances of depressed marmatite and depressed chalcopyrite, the respective equations of their flotation models were derived and presented.IntroductionCyanidation tailings are the solid residues generated by gold plants that use cyanide to extract gold (Lv, Ding and Qian, 2015; Zhang, Li and Yu, 2013). Because of increasing demand for gold, the Chinese gold industry has developed rapidly, with production amounting to 451.799 tons in 2014, an increase of 5.5 percent from 2013. Chinese gold production has been the highest in the world for eight consecutive years. As a result, more than 2.45 million tons of cyanidation tailings are estimated to be discharged into tailings ponds every year (Li et al., 2010; Lv, Ding and Qian et al., 2015; Wang et al., 2015; Zhang, Li and Yu, 2013; Zhang, Li and Yu, 2012), and approximately 300 million tons of cyanide tailings are stockpiled in China, with the potential to cause serious environmental pollution as well as death to wildlife (Adams and Lloyd, 2008; Donato et al., 2007; Hewitt, Breuer and Jeffery, 2012; Velasquez-Lopez et al., 2011; Stephen et al., 2009; Zagury, Oudjehani and Deschenes, 2004). Concerns over cyanidation tailings are not exclusively environmental but also economic, as tailings occupy considerable land area, and tailings storage facilities increase the production costs of gold enterprises (Donato et al., 2007). Tailings often contain other valuable metals such as zinc, lead and copper. For example, the cyanidation tailings of Gaoyao Hetai Gold Plant in Guangdong Province contain 2.5 percent copper (Cu), 0.31 percent lead (Pb), 0.23 percent zinc (Zn) and 15.36 percent iron (Fe) (Shi, 2008), and the tailings of Tianshui Gold Plant in Gansu Province contain 1.94 percent Cu, 5.96 percent Pb, 0.27 percent Zn and 24.62 percent Fe. Cyanidation tailings have therefore been increasingly viewed as a secondary resource rather than waste."

Jan 1, 2016

By J. J. Rutledge

I. DESCRIPTION OF THE CLINTON ORES AND ASSOCIATED POCKS. THE Clinton rocks in Stone Valley comprise (1) thick layers of deep-red shale, (2) layers of reddish-gray shale interspersed with beds of sandstone and thin beds of extremely fossiliferous limestone, and (3) yellowish-gray shales alternating with thin layers of olive-colored shales. These layers of shale are all very thin and are at no point massive.1 A bed of gray-white sandstone varying in thickness from 12 to 30 ft. occurs in the tipper portions of the Clinton shales. This is called the ore sandstone, a name given to it by Rogers and adopted also by the Second Pennsylvania Geological Survey. It is the surest guide to the presence of the iron-ore bed, which lies below its lower edges at distances varying from 10 to 20 ft. This ore sandstone, in the valley, lies generally at very low inclinations, but often is locally subjected to considerable changes in dip. At its outcrop this ore sandstone weathers very easily and yields a rather sparse crop of stone, Composed of dirty, iron-stained boulders. Upon the roads these boulders are quite well rounded, and bear fragments of crinoid stems and other fossil forms. The ore sandstone exhibits at many points evidences of former movements in this very great thickness of the shales, and as it is the only stratum in this series competent to transmit and record stresses due to structural movements, its evidence is of considerable importance in determining the occurrence of movements in times past.

Nov 1, 1908

By J. E. Forciea, R. W. Salmi

Operating and research personnel at U.S. Steel's Pilotac concentrator have evolved specifications for magnetic separators suitable for use in beneficiation of Mesabi magnetic taconite. These specifications were developed as a result of investigations into the operating and metallurgical problems at the Pilotac concentrator over a period of some ten years. This paper discusses primary magnetic separator specifications, but much of the information is also pertinent to secondary and tertiary magnetic separators. Of particular significance is the proposal of a new basis for specifying the magnetic field which includes consideration of both field strength and field gradient. Other areas of discussion include flowsheet service, operating conditions such as drum speed and pulp level, tank configuration, magnet strength including field gradient, sleeve bearing design, designation of corrosion resistant materials and other details that result in a metallurgically efficient machine that has low repair and maintenance requirements. The mechanical and metallurgical design of magnetic separators at the Pilotac plant, Minnesota Ore Operations, United States Steel Corp. has progressed from the original single-stage, belt-type machines to the present multiple-stage, drum-type units, In ten years of operation, the plant operating and research personnel, in consultation with manufacturers, have made design changes to improve mechanical, electrical and magnetic features to meet process needs as flowsheet designs developed and to incorporate new permanent magnet materials as they became available. Separator specifications were an end result of this effort. The latest specifications which were developed for the Minnesota Ore Operations' plant were not all-inclusive listings; they covered only those points indicated by plant experience. For example, magnet pole piece design and dimensions were not stated. The manufacturers were given freedom to use any design as long as the field pattern was as specified. The selection of the items to be included in the specifications was undoubtedly influenced by particular conditions at Pilotac such as composition of plant water, concentration characteristics of the ore, repair and maintenance facilities available and the research programs that had been conducted. Only the developments leading to the specifications for a primary or "cobber" magnetic separator are presented in this paper. However, the same general concepts are used to specify secondary and tertiary separators. The areas of interest discussed include flowsheet service, tank configuration, magnet design, bearings, materials of construction, and some minor mechanical details. FLOWSHEET SERVICE The primary magnetic separators in the Pilotac Concentrator flowsheet are located after the first stage of grinding as shown in Fig. 1.

Jan 1, 1965

By P Stephenson, G Mosher, M Berry, C Arnold, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Globally, private minerals companies considering the transition to a public company and entrepreneurs looking to create a new public company through, for example, an initial public offering or by a reverse takeover have many options. For companies with assets around the Pacific Rim, there are arguably five key stock/securities exchanges that actively promote international minerals company listings, and these are located in Australia, Canada, Hong Kong, Singapore and the United Kingdom.Listing on any of these exchanges requires a range of technical, commercial, financial and legal documentation. Each exchange has specific rules and requirements for technical documentation to support the listing process. Once listed, each exchange also has specific rules for technical information to meet ongoing compliance requirements. The nature and detail of this documentation differs for the five exchanges.This paper presents statistics on the minerals company listings on each exchange and provides an overview of the technical documentation required to prepare for an initial listing and ongoing compliance.CITATION:Berry, M, Stoker, P, Stephenson, P, Arnold, C and Mosher, G, 2015. Technical considerations of public listing and ongoing compliance for minerals companies , in Proceedings PACRIM 2015 Congress, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. F. Sirianni

The Peace River iron ore deposit represents the sole source of raw material for an integrated steel industry in Alberta. The ore has proved refractory to beneficiation by a number of techniques. A selective oil-phase agglomeration technique is described. Medium-grade concentrates, analyzing 48-53% Fe and 10-14% SiO2 were obtained with recoveries of about 75% of the total iron. These results appear to represent the optimum possible for this ore body.

Jan 1, 1977

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By John D. Weibmer

A strong step towards acknowledgement of mining as a skilled trade has been taken by the Tintic Division of Kennecott Copper Corp. In May 2 ceremonies, a pilot program was signed into force which, possibly for the first time in US history, recognizes mining as an apprentice trade and grants journeyman status to those who complete the prescribed training sequence. The apprenticeship standards, hammered out after months of consultation between management, labor, and government, are presently limited only to underground hard-rock mining and only within Kennecott's Tintic Division, but the architects of the program are confident that the concept will spread-first to other underground operations where miners desire documented evidence of their special skills, then to open-pit and soft-rock operations.

Jan 6, 1977

By Z. H. Liu

We experimented with slurry which from one of coal preparation plant in Guizhou province and made researches on double hump gradation, one of critical factor of gradation technology, which can influence pulping character in the process of making coal water mixture (CWM). The purpose for it is to find the best particle gradation which can meet the requirements in concentration, viscosity, and stability for CWM. The final result is that the concentration, viscosity, stability of CWM can meet the requirement for industrial use while the rate of fine particle in the slurry is 70%~75% and the maximum concentration of 62%.

Jan 1, 2014