Search Documents

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By Oliver M. W. Sprague

THIS gold problem is full of complications and can hardly be handled adequately or comprehensively in any short period of time. Perhaps I might begin by mentioning a few aspects of the subject about which I suppose there will be no disagreement. The first of these is that we already have a stock of monetary gold in the United States far in excess of what is needed to support any desirable increase in the present volume of currency and credit. The second is that this already superabundant gold stock is certain to be considerably enlarged during the course of the war, and presumably during the months of readjustment following its conclusion. Some billions of additional gold, we may reasonably presume, will come into the country during these next few years, thus increasing the aggregate monetary gold stock from the present eighteen billions to perhaps twenty- two or even twenty-five billion dollars.

Jan 1, 1940

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By T. Yameogo

Many ideas, tools, technologies, and methodologies are believed to have staked their claims on the future of mining. For example, automation is strongly positioned as the platform within which mining will be practiced. A subset of automation ? intelligent mining ? will add some smart interactions between machines, technologies, the rock, and the environment. The future also calls for an improved approach to sustainability and corporate social responsibility. Mines of the future are dreamed of to be more ethical and more balanced. They will boast optimized designs, integrated value and supply chains, produce less waste, recycle and reuse, and will require less energy to operate. Then, what about the people that will operate this optimized ecosystem? How is the education system teaching the operators of the mines of the future? What kind of a future should mining education foresee to prepare the workers appropriately? In recent years, the shortage of skilled labor for mines around the world has created a tough competition to attract, retain, and train the very people without whom mining will cease to exist. In Australia, Canada, and the United States in particular, the war for talent has resulted in higher-than-usual labour costs. Such costs have dented the unit costs of many mining businesses. Concomitantly, mining contractors? and consultants? prices have increased to reflect the escalation of labour costs across the value chain. From labourers to engineers, from juniors to seasoned professionals, the increase in compensation is unprecedented. Yet, the shortage is still hurting the industry, and the high calibre candidates continue to be rare gems. The industry has been implementing aggressive solutions that include the increased hiring of skilled immigrants, the training and recruitment of minorities, and the retaining of near-retirement experienced employees. Public relation campaigns about the benefits of embracing careers in mining are also common. The CIM has also devoted a ?M4S? section to its pan-Canada meetings to educate the public, especially the youth, about the importance of the mining industry for Canada. Moreover, mining associations and universities are enticing students? enrolment through scholarships and financial support. Still, the balance between quantity and quality of workers can be discussed. This paper intends to discuss the present state of mining education as an essential part of the future of mining. The authors brush the picture of the education of miners, technicians, and engineers, against the backdrop of the technology-advanced mines of the future.

Aug 1, 2013

As mines become deeper, the problems of heat in the workplacebecome more acute. An important response from the industry hasbeen the widespread adoption of microclimate cooling such asair-conditioned cabins. However, not all work in mines can becompleted from inside an air-conditioned cabin, and in any event,it is still important to keep the ambient air in the mine outside ofany microclimate to a safe temperature. An important method forbringing workplace temperatures under control is the appropriateuse of refrigeration. The application of refrigeration inmechanised mines has been recently described (Brake, 2001;Brake and Fulker, 2000). This paper provides an overview ofsome of the important engineering considerations in thespecification and selection of mine refrigeration plants. Thepurpose is to provide a basic understanding of refrigerationprinciples, practices, terminology, hazards and opportunities formining engineers or other personnel who may need to beinvolved in the introduction of refrigeration onto a mine site.

Jan 1, 2001

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By Augusto Díaz Rodríguez

Como parte de la campaña de seguridad y prevención de accidentes producidos en las minas de San Antonio de Esquilache, el autor del presente texto expone una serie de medidas que permitan reducir el índice de siniestros producidos durante las labores tales como: golpes con herramientas, carroneo, explosivos, lesiones, caídas de piedras por chimeneas, de trozo y minerales en los buzones, etc. Para ello, resalta la creación de organizaciones dedicadas a prevenir dichos incidentes, así como la aplicación de un programa de seguridad que incluya el uso de cinturones de seguridad, acuñado de los techos y galerías mediante barretillas, limpieza de caminos y carretillas, supervisión contínua de los caminos de las minas, equipo de seguridad del trabajador, et. Por último, la permanente charla de capacitación del personal de seguridad, como la cooperación de los trabajadores durante este proceso, disminuye la cantidad de 4o accidentes mensuales a 2 desarrollados en los últimos meses en la mina.

Jul 20, 1955

By P Cameron

MetPlant conferences have focused on ensuring mining projects are well designed then optimised to operate safely and effectively at the top end of world’s best practice to ensure shareholders are not just happy but delighted. This assumes the MetPlant was built right the first time. However, reality is, too often Plant Metallurgists (PlantMets) find after commissioning they are faced with the expensive task of correcting errors or modifying shortcomings to achieve product quality at name-plate capacity, i.e. get it right the second time. Why do companies spend good money to engineer an excellent feasibility study then allow “wise men” remote from the project team to impose cuts in budget and schedule, often under the guise of value engineering? Since mining is full of uncertainties, such actions can increase the risks of failure with the result that some MetPlants do not work well. Can PlantMets influence the remote wise men who often are also imposing the rules for lending and the required returns to appreciate the uncertainties of mining and their associated risks then let the project team get it right the first time? PlantMets can negotiate with the wise men from the outset of the project and bring them into an outer layer of the team where they can understand the risks then share responsibility and accountability to achieve the common goal of building a MetPlant which works well the first time and deliver the forecast profits. Since shareholders are not in the business to make losses they appoint a Board of Directors to deliver the best outcomes for the shareholders. Thus the Board should seek effective advice on the risk reward implications from the PlantMet before making their decisions.CITATION:Cameron, P, 2015. Do all metplants work well? PlantMets can ensure they do, in Proceedings MetPlant 2015, pp 2–9 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By Li-ming Qi

During mining, the stress in the coal face varies, and, at the same time, the gas flows from the coal body into the excavation, which will cause the gas pressure to change continuously. Assuming the coal gas content of the coal to be constant, and applying the law of energy conservation, the influence of stress concentration on the gas pressure was analysed. It was found that the stress is proportional to the gas pressure. Finally, as a result of analysis and the law of gas flow, the gas pressure dynamic distribution ahead of tunnelling was modelled, and the mechanism by which blasting induces outburst was explained by making use of the model. Keywords: gas pressure, stress concentration, excavation, tunnel.

Jan 1, 2007

By Rick Piovesan, Pramod Rao, Nihal Bohra, Mark Wahler

"This paper discusses the approach followed for the geotechnical design of 355 mm and 457 mm diameter driven open-ended steel pipe piles used for a gas plant at a green field site in Pilbara region in Australia. The principal bearing layer at the site comprises of calcareous Red Bed soils and weak rock, which is the typical geology along a significant length of the northern Western Australian coastline with carbonate content up to 70%. The uncertainty associated with the mechanical behavior of the calcareous soils and cemented soils (weak rocks) presented design challenges in the selection of appropriate pile design method and design parameters for pile capacity estimation during Front End Engineering Design (FEED). The American Petroleum Institute (API)-based design methodology was adopted. The representative design parameters for the Red Bed weak rock were established by treating the weak rock as clay with undrained shear strength as one-half of the characteristic unconfined compressive strength (UCS) value. Both statically load tested and CAPWAP (Case Pile Analysis Wave Program) estimated ultimate axial pile capacities on 25 early pre-production indicator piles demonstrated that the API design methodology for siliceous soils provides reasonable prediction of axial pile capacity in the red bed soils/weak rock and no reduction to API computed axial capacity due to carbonate content is warranted. The results also demonstrated that penalizing axial pile capacity solely based on carbonate content is not appropriate.IntroductionA gas processing facility was proposed to commercialize the gas reserves located 130 km offshore from the north-west coast of Western Australia (WA). The project site is a green field site located in the Pilbara region along the northwest coast of WA. Specific information regarding the site has been withheld due to confidentiality reasons. The site layout is shown in Figure 1.The site comprises low-lying tidal flats, clay pans and sand dunes covered with low scrub. The onshore site levels vary from elevation 1 m to 10 m AHD (Australian Height Datum), with the largest proportion of the area (excluding sand dunes) between elevations of 1 m and 3 m.The onshore facilities are to comprise a liquefied natural gas (LNG) plant site, a construction camp, the land-based portion of the materials offloading facility (MOF), roadways, and borrow pit areas.The existing ground levels within the process train area, where pile load testing was performed, vary from over 7 m AHD where the summits and peaks of the central dune exist to typically 1 m to 2 m AHD towards the east and west edges of the dune. The proposed finished grade for the process train is set at 7 m AHD."

Jan 1, 2015

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997

By Carlton H. Baab

In June, 1981 the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the U.S. coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent". Until recently, clean coal has had a low selling price and satisfying the purchasers' specifications required only minimum cleaning. However, it is becoming more apparent that the increases in coalfired utility power plants forced outage rates are relative to the deterioration in the quality of fired coal. Utility companies are becoming aware of the economic value of reducing the variability of ash, moisture and sulfur in steam coal purchase orders. New contracts are currently being negotiated between electric utilities and coal producers that include provisions for increased penalties if the product does not meet specifications. With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. This paper discusses the various types and applications of nuclear instrumentation currently in use in the coal preparation industry.

Jan 1, 1983

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A. Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30 000 tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors, in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400 m causing a major failure of the north-west wall involving close to 100 Mt of waste material.

Jan 1, 2006

By John B. Tieder

Arbitration is a legally recognized alternate litigation for the resolution of civil disputes. The parties agree, either before or after a dispute arises, to submit that dispute to an independent third party for resolution. The decision of that third party is binding on the parties. A decision of an arbitral tribunal, typically referred to as an "award," cannot be reviewed by a court except on very limited grounds, such as fraud. See, e.g., Va. Code 8.01-581.010. Indeed, an arbitral award is typically less subject to judicial review than the decision of a trial court, whose decisions are almost always subject to appellate review as a matter of right. Arbitration is typically the result of a contractual agreement between the parties to submit disputes to arbitration. On occasion, arbitration can be required by statute. For example, the California Department of Transportation requires the arbitration of all disputes arising under its contracts. Public Contract Code, Article 7.1 (§§10240-10240.13). There may be a question whether statutorily required arbitration is truly arbitration or an administrative law disputes resolution procedure. The significance of the difference is that the decisions of administrative law bodies are typically reviewable by a court of law as a matter of right while, as set forth above, arbitral awards are almost never reviewable.

Jan 1, 1988

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017